Whittier Wood Furniture McKenzie 2346AFGAC User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 05/14
McKenzie Mantel Beds
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Model #
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
2346AFGAC;
2346AFCAF
McKenzie Queen
Mantel Bed
2349AFGAC;
2349AFCAF
McKenzie King
Mantel Bed

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Parts List
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 2 —05/14
Please identify the parts and check that the quantities received match those on this list. If you need
to replace a part, refer to the model number, part letter and name.
2347AFGAC; 2347AFCAF
Q. Mantel Headboard/Footboard Kit (x1)
Part
Description
Quantity
A
Headboard Assembly
1
B
Footboard Assembly
1
C
Assembled Foot
4
D
Queen Slat (60-5/8")
5
E
#8 x 1-1/4" Black Screw
10
F
Adjustable Glide with Hex Nut (installed)
4
G
5/16" x 3/4" Insert Nut (inserted)
4
H
1/4" x 80mm Hex Bolt
2
I
1/4" x 45mm Hanger Bolt (inserted)
4
J
Hex Wrench
1
T
#8 x 2" Black Screw (inserted)
2
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bed Bracket (attached)
2
ZR
Right Bed Bracket (attached)
2
ZU
1/4" T-Nut (inserted)
5
ZX
#8 x 1-5/8" Black Screw (inserted)
8
Please note this Assembly Instruction is for McKenzie Queen Mantel Bed (#2346) and
McKenzie King Mantel Bed (#2349). The Parts Lists for each component follow.

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Parts List
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 3 —05/14
2350AFGAC; 2350AFCAF
K. Mantel Headboard/Footboard Kit (x1)
Part
Description
Quantity
A
Headboard Assembly
1
B
Footboard Assembly
1
C
Assembled Foot
4
D
King Slat (76-9/16")
5
E
#8 x 1-1/4" Black Screw
10
F
Adjustable Glide with Hex Nut (installed)
4
G
5/16" x 3/4" Insert Nut (inserted)
4
H
1/4" x 80mm Hex Bolt
2
I
1/4" x 45mm Hanger Bolt (inserted)
4
J
Hex Wrench
1
T
#8 x 2" Black Screw (inserted)
2
YH
Top Assembly
1
YI
#8 x 1-1/4" Pan Head Screw
2
YJ
Cam Connector (inserted)
2
YK
Cam Housing
2
ZP
#8 x 1" Black Screw (inserted)
16
ZQ
Left Bed Bracket (attached)
2
ZR
Right Bed Bracket (attached)
2
ZU
1/4" T-Nut (inserted)
5
ZX
#8 x 1-5/8" Black Screw (inserted)
4

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Parts List
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 4 —05/14
2348AFGAC; 2348AFCAF Queen/King Rail Kit (x1)
Part
Description
Quantity
K
Side Rail
2
L
#8 x 5/8" Flat Head Screw (inserted)
16
T
#8 x 2" Black Screw (inserted)
22
ZQ
Left Bed Bracket (attached)
2
ZR
Right Bed Bracket (attached)
2
ZU
1/4" T-Nut (inserted)
4

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Assembly Instructions
This assembly requires two people.
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 5 —05/14
Tools Required: 4mm Hex Wrench (provided), Phillips screwdriver
1. Remove the Slats (D) from the back of the Headboard (A) and place them off to the side. See
Figures 1 and 1a.
Notes:
Step 2 & 3 are for the McKenzie King Mantel Bed (#2349) only.
2. NOTE: READ CAM INSTRUCTIONS NOW BEFORE YOU BEGIN THE FOLLOWING STEP.
Insert Cam Housings (YK) into the two pre-drilled holes on the Headboard Assembly (A) as
shown in Figure 2. Lower Top Assembly (YH) so that the Cam Connectors (YJ) fit into the
housings (YK) tighten the cam housings as indicated in the Cam-lock System instructions.
See Figures 2 and 2a.
Fig. 1
Shipping Straps
D
A
Fig. 1a
A
D
Shipping Straps
(For 2346)
(For 2349)
Fig. 2
A
YH
YK
x 2
YK
Fig. 2a
YK
YJ
YK

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Assembly Instructions
This assembly requires two people.
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 6 —05/14
3. Attach the Top Assembly (YH) to the Headboard Assembly (A) by inserting two #8x1-1/4" Pan
Head Screws (YI) into the predrilled holes in the block that is attached to the Headboard
Assembly (A). See Figures 3 and 3a.
4. To attach the Footboard (B) to the Side Rail (K), align the Brackets and slide the Side Rail down
on to the Footboard (B). See Figures 4 and 4a.
Fig. 3
YI
x 2
Fig. 3a
YI
Fig. 4
K
B
Fig. 4a

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Assembly Instructions
This assembly requires two people.
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 7 —05/14
5. Repeat step four for the other side. See Figures 5 and 5a.
6. Align the Brackets on both sides and slide the Side Rail/Footboard assembly down on to the
Headboard (A). See Figure 6.
Fig. 5
K
Fig. 5a
Fig. 6
A

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Assembly Instructions
This assembly requires two people.
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 8 —05/14
7. Using the Hex Wrench (J), attach the Headboard to the Side Rails with two 1/4" x 80mm Hex
Bolts (H). See Figure 7.
8. Attach an Assembled Foot (C) to four of the five Slats (D) as shown in Figure 8.
Fig. 7
H
H
x 2
J
x 1
D
Fig. 8
X 4
C

2346AFGAC; 2346AFCAF McKenzie Queen Mantel Bed;
2349AFGAC; 2349AFCAF McKenzie King Mantel Bed
Assembly Instructions
This assembly requires two people.
2346AFGAC_2346AFCAF_2349AFGAC_2349AFCAF_Page 9 —05/14
9. Move the bed assembly to its final position. Position the Slats (D) on the bottom edges of the
rails and place the slat without the Assembled Foot nearest to the Footboard. Attach with
#8 x 1-1/4" Black Screws (E). See Figure 9.
10. Adjust the Adjustable Glides with Hex Nut (F) on the Assembled Feet (C) so the Glides just
touch the floor, making sure the Assembled Feet bear weight.
E
x 10
Fig. 9
E
Slat without
an
Assembled
Foot.
D
F
Fig. 10
C

CAM - LOCK SYSTEM INSTRUCTIONS
P.O. Box 2827
Eugene, OR 97402 USA
Toll Free: 800-653-3336
Ph: 541-687-0213
Fax: [phone]
www.whittierwood.com
Page 1 of 1
Rev. 01/13
NOTE: To avoid scratching the surface of the
wood, assemble the unit and place face-down
on a clean, protected surface.
12 1
2
3
4
5
6
7
8
9
10
11
Optimum
tightness
Face of
Cam Housing
Correct way to tighten
your Cam-Lock system.
Cam Connector
Shoulder must be
flush with the surface
of the wood.
DO NOT embed
the shoulder into the wood!
1. Insert the Cam Housing so the arrow faces the Cam
Connector. To achieve tension and holding power,
you MUST TURN the Cam Housing clockwise at
LEAST 1/4 turn to the 9:00 position. Turning the
Cam Housing between 1/4 and 1/2 turn should be
enough to ensure rigid tension. Tension should be
initiated as soon as 10:00. You should receive
optimum tightness at 11:00. IF this does not occur,
tighten or loosen the Cam Connector to achieve
proper tension.
2. You may need extra tension if:
A. The Cam Connector was screwed in deeper or
not as deep as if should.
B. If the furniture is repeatedly assembled and
disassembled.
C. If you place a heavy load in the unit.
To achieve extra tension,tighten the Cam
Connector between the 11:00 and 12:00
positions.
Shelf
Side Panel
Cam
Connector
Cam
Housing
Install the Cam
Housing so the
arrow is directly
over the bolt.
Lock the Cam
Housing with:
Phillips
Screwdriver
Slotted
Screwdriver