Whittier Wood Furniture McKenzie Twin Headboard User manual

Production Code:
11/09
VN
P.O. Box 2827
Eugene, OR 97402 USA
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions and Finishing Hints before
you begin your project.
Service Policy: We will replace any part that is
defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly by phone, fax, mail or
email for a replacement part.
To Order: Provide the furniture model number (upper
left corner of this page), the part letter, production
code, quantity needed, reason for replacement, your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one
or two business days from the time we receive your
request. Please allow five to ten business days for delivery.
CALL US FIRST! Do not return this item to the store.
800-653-3336 • Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Hours: Our friendly customer service staff can be
reached Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific
Time). You may leave a message 24 hours a day,
seven days a week.
Before you load or move this item, check to make
sure all screws and supports are tight.
.
Before you begin your project, completely read the
Assembly Instructions and Finishing Hints.
For normal household use only. Not recommended
for commercial use.
Store this item: 1- in its box; 2- in a dry place; 3- in
temperatures that range from 40° to 90° (not on a
cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your furniture. Tighten or
repair as needed.
IMPORTANT NOTES:
Model #
AUF McKenzie Headboard
1356AUF McKenzie Twin Headboard
1357AUF McKenzie Full/Queen Headboard
1358AUF McKenzie King/Cal-King Headboard
Assembly Instructions
1357AUF shown

1356AUF McKenzie Twin Headboard
1357AUF McKenzie Full/Queen Headboard
1358AUF McKenzie King/Cal-King Headboard — Parts List
A — Headboard Assembly — Qty.1
(for 1357AUF & 1358AUF)
1357AFUF shown above.
F — Headboard Assembly
— Qty.1
(for 1356AUF)
B — Block 1
— Qty. 2 (attached)
(for 1357AUF & 1358AUF)
G — Block 2
— Qty. 2 (attached)
(for 1356AUF)
C — #12 x 2½" Pan Head
Screw — Qty. 8 (inserted)
Page 2 — 1356AUF_1357AUF_1358AUF — 11/09
H — #8 x 1-5/8" Black Screw
— Qty. 4 (inserted)
I — #8 x 20mm Pan Head Screw
— Qty. 17 (inserted) (1356AUF)
— Qty. 22 (inserted) (1357AUF)
— Qty. 26 (inserted) (1358AUF)
D — #12 x 1¼" Pan
Head Screw — Qty. 6
E — Washer
— Qty. 6
Before you begin this assembly, identify each part and make sure quantities received match what is on this list.
If you need to replace a part, please refer to following list for its name and letter code.
Assembly Instructions
Tools Required: Drill, 1/8" bit, Phillips screwdriver
1.
IF YOU ARE USING A HOLLYWOOD BED FRAME:
Adjust the Hollywood frame to fit your matress and box spring.
2. Place the Headboard (A) against the end brackets of the frame and mark the locations for
the screws. Drill pilot holes approximately 1¼" deep. (To make sure you don’t drill deeper,
measure 1¼" up from the end of the drill bit and wrap a piece of tape around the bit. Stop drilling
when the edge of the tape meets the wood.)
3. Position the Headboard (A) against the frame and attach using #12 x 1¼" Pan Head Screws (D)
and Washers (E).

Rubber
gloves
Rags
Paper towels
Q-tips
Tack cloth
Drop cloth
Paint brushes
(bristle and
foam)
#220 & #320
sandpaper
Mineral spirits
Masking Tape
Rev. 8/07
Finishing Hints
Choosing the Finish:
Getting Started
1. Choose a finish that will meet your expectations for
the product you are finishing. Are you matching
existing furniture or do you want a “natural” finish?
Is the piece to be functional, decorative or both?
The answers to these questions may affect the
type of finish you choose.
1. Assembly Instructions may contain special
finishing information for that item. Read both
the Assembly Instructions and these Finishing
Hints completely before beginning.
2. Sand the entire piece, using #220 grit sandpaper.
Sand with the grain of the wood on flat surfaces
and opposite the grain on turnings. Some parts
are plywood. Be careful not to sand through the
veneer. End grain (table top ends, seat edges,
grooves on turnings, etc.) accepts more stain.
Extra sanding in these areas with a #320 grit sand-
paper will reduce stain absorption, creating a more
evenly stained piece.
3. When sanding is completed, wipe the surface of
your furniture with a cloth or tack rag. Make sure
the item is free of dust before proceeding.
2.
Use products of the same brand to ensure compat-
ibility of products.
4. We recommend using a wood conditioner under oil
base stains.
5. Work in a well ventilated and well lit area.
3.
ALWAYS follow the stain manufacturer’s instruc-
tions. Alder is a porous hardwood
and often
looks best when following the finishing directions
for softwoods
1. Read and follow label directions. Stir stain well
before starting.
4. Q-tips are ideal for hard to reach areas.
5. Allow to dry thoroughly before proceeding.
2.
Test stain on an inconspicuous spot on your proj-
ect, or use the sample chip if one is provided. The
sample chip must be sanded in the same way as
your furniture kit to ensure the piece will accept the
stain similarly. Put at least one coat of your top coat
over the stain sample, as it also affects the look of
the stain. Test every type of wood that is in your
kit. Some of our products include more than one
type of wood, which may react differently to the
stain color. Sample chips for the different woods
may be included. It may be necessary to add a
second coat of stain to lighter woods to match the
darker woods in your kit.
3. Apply stain with a poly brush or lint-free cloth. Apply
stain over a small area and wipe off excess. Work-
ing in small areas will make the color easier to con-
trol.
1. Always read and follow all label directions. Stir
your finish coat gently, do not shake. It will create
bubbles that are hard to remove.
2. All surfaces (including the underside of table tops
and inside drawers) must be sealed with at least
one layer of a top coat. This will help minimize
wood swelling, shrinkage, warping and cupping
due to changes in moisture content or temperature.
3. We recommend that you apply a minimum of two
coats when using polyurethane or varnish
(especially on all table top and work surfaces).
Sand lightly between coats using a #320 grit sand-
paper or 00 steel wool for the smoothest possible
finish.
4.
Some water-based finishes tend to raise the grain
slightly. This can be easily controlled with this sand-
ing step. However, do not use steel wool when using
water-based finishes. Strands of steel fiber caught
in the wood can cause rust spots when coated with
any water-based product.
1. For best results when painting, first coat the wood
with a primer. An oil based primer would be best for
a smooth finish. If you do not wish to use a solvent
based primer, a water based primer would work
almost as well.
2. Buy a quality brand paint. You may use a satin,
semi-gloss, or gloss sheen. Apply a second coat
for a smooth finish. Lightly sand between coats
using a #320 grit sandpaper, so that the second
coat will bond well. Repeat as desired.
3. Since there is such a variation between paint
manufacturers, refer to your paint supplier for spe-
cific advice on using the paint that you purchase.
Staining
Applying the Top Coat:
Painting:
No top coat is required if using paint.