Whittier Wood 3452AFCAFa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/14
Model #
3452AFCAFa
Stayton End Table
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Unload items before you move this unit.
Do not overload the drawer or shelf.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

3452AFCAFa Stayton End Table
Parts List
3452AFCAFa —Page 2 —03/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top Assembly (attached)
1
B
Side Assembly
2
C
Shelf Assembly
1
D
Drawer Box (inserted)
1
E
Drawer Face (installed)
1
F
Drawer Slides (pre-installed sets)
1
G
#6 x 3/4" Philtruss Screw (inserted)
6
H
#6 x 1/2" Philtruss Screw (inserted)
6
J
#8 x 1-1/4" Pan Head Screw
20
(6 inserted)
Ka
#8 x 1-1/2" Machine Screw Tuscan (installed)
2
L
#8 Washer (inserted)
12
M
Insert Nut (inserted)
4
N
Pull (installed)
1
O
Wood Dowel (inserted)
4
P
#8 x 20mm Pan Head Screw (inserted)
6
Q
Adjustable Angle Bracket (attached)
2
R
Adjustable Glide (installed)
4
S
#8 x 7/8" Black Lo-Profile Screw (inserted)
4

3452AFCAFa Stayton End Table
Assembly Instructions
3452AFCAFa —Page 3 —03/14
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (D) from the Top Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a.
2. Turn the Top Assembly (A) face down on a clean protected surface. Place a Side Assembly (B)
against one side of the Top Assembly as shown. Insert four #8 x 1-1/4” Pan Head Screws (J)
through the holes in the Side Apron into the Side Assembly. Insert one #8 x 1-1/4” Pan Head
Screw (J) through the pocket hole in the Back Apron into the Side Assembly. See Figure 2.
Fig. 1
Drawer Release Lever
Fig. 1a
Fig. 2
B
A
J
x 5
J
J

3452AFCAFa Stayton End Table
Assembly Instructions
3452AFCAFa —Page 4 —03/14
3. Turn the Top/Side Assembly leg side down. With the bottom side of the Shelf Assembly (C)
facing down place the dowels of the Shelf Assembly (C) into the dowel holes in the legs. See
Fig. 3. Place the remaining Side Assembly (B) over the remaining dowels in the Shelf
Assembly. See Figure 3.
4. Rotate the Top/Side/Shelf Assembly back onto its Top. Insert four #8 x 1-1/4” Pan Head Screws
(J) through the holes in the Side Apron into the Side Assembly. Insert one #8 x 1-1/4” Pan Head
Screw (J) through the pocket hole in the Back Apron into the Side Assembly. See Figure 4.
Fig. 4
B
J
x 5
J
J
Fig. 3
B
C

3452AFCAFa Stayton End Table
Assembly Instructions
3452AFCAFa —Page 5 —03/14
5. Using the pocket holes as guides, secure the Shelf Assembly (C) to the Side Assemblies (B)
with four #8 x 1-1/4" Pan Head Screws (J). See Figures 5 and 5a.
6. Turn the table upright and insert the Drawer.
7. Place the table at its final destination. To level the table, rotate the Adjustable Glides (R) found
on the bottoms of the legs. See Figure 6.
Fig. 5
J
x 4
J
Fig. 5a
Fig. 6
R
R