Wholesale Interiors BBT 6628 User manual

ASSEMBLY INSTRUCTIONS
FURNITURE PART LIST
ITEM DESCRIPTION QTY
AHEADBOARD 1 PC
BSUPPORT BOARD 2 PCS
CHEADBOARD WINGS (L&R) 2 PCS
HARDWARE PART LIST
ITEM DESCRIPTION QTY
1JCBB BOLT M8 x 50mm 4 PCS
2JCBC BOLT M6 x 45mm 4 PCS
3M8 FLAT WASHER 4 PCS
4M8 SPRING WASHER 4 PCS
5M6 FLAT WASHER 4 PCS
6WOOD DOWEL M8 x 30mm 4 PCS
7M4 ALLEN KEY (BALL SHAPE) 1 PC
8M5 ALLEN KEY (BALL SHAPE) 1 PC
Read instructions carefully. See furniture and hardware part
list on the right for guidance.
Have all parts ready before assembly. Place all wooden furniture
parts on a clean and flat soft surface to prevent scratching.
Before you start, here are some words of caution:
1. Do not FULLY - TIGHTEN nuts and bolts until all nuts and bolts are partially tightened.
2. Do not FULLY - TIGHTEN nuts and bolts to avoid causing damage to the threading.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Hammer (not provider).
MODEL : BBT 6628 KING HB
STEP 1 STEP 2
A
B
34
1
8
x 2
1 OF 2
Secure each support stand by using 2x JCBB Bolt [1] , 2x M8 Flat Washer [3] and
M8 Spring Washer [4].
Tighten with supplied Allen Key [8].
Repeat the same procedure to secure the other side
1.1 Open the zip at the headboard backing and take out all the parts.
1.2 Insert the support board from the bottom, align pre-drilled
support board holes over the pre-drilled headboard holes.

ASSEMBLY INSTRUCTIONS
STEP 3 STEP 4
STEP 5
2
C5
7
2 OF 2
C
6
x 2
Fit wood dowels [6] into headboard wing [C].
Your headboard assembly is complete.
Note: Hardware may loosen over time. Periodically
check that all connections are tight.
Assemble headboard wing [C] to headboard [A] using the JCBC Bolts [2]
and M6 flat washer [5] using Allen key [7].

FURNITURE PART LIST
ITEM DESCRIPTION QTY
AHEADBOARD 1 PC
BBED FRAME
(DOES NOT INCLUDE
WITH THE PURCHASE) -
HARDWARE PART LIST
ITEM DESCRIPTION QTY
1JCBB BOLT M6 x 60mm 4 PCS
2JCBB BOLT M6 x 35mm 4 PCS
3M6 FLAT WASHER 8 PCS
4M6 SPRING WASHER 4 PCS
5M6 HEX NUT 4 PCS
6M4 ALLEN KEY (BALL SHAPE) 1 PC
STEP 1 STEP 2
B
A
A
B
5
3
3
4
1
6
Note: Extra screws were provided
for attaching the headboard to your
bed frame (use is optional).
1. Line up the bed frame board's pre-drilled holes
to match those of the headboard.
2. Secure the headboard to the bed frame by
using 2x JCBB bolt 60mm (1) for the thicker bed
frame, and 2x JCBB bolt 35mm (2) for the thinner
bed frame. Before inserting each bolt, place a M6
spring washer (4) and M6 flat washer (3) on each
bolt. Then fit a M6 flat washer (3) on the screw as
it protrudes through the other side of the bed
frame.
3. Place a M6 Hex Nut (5) after the M6 flat washer
(3) at the end of each screw. Then tighten by using
the M4 Allen key (6).
4) Repeat the same procedure for each screw and
each side of the bed frame.
Read instructions carefully. See furniture and hardware part
list on the right for guidance.
Have all parts ready before assembly. Place all wooden furniture
parts on a clean and flat soft surface to prevent scratching.
Before you start, here are some words of caution:
1. Do not FULLY - TIGHTEN nuts and bolts until all nuts and bolts are partially tightened.
2. Do not FULLY - TIGHTEN nuts and bolts to avoid causing damage to the threading.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
ASSEMBLY INSTRUCTIONS (BED FRAME)
MODEL : BBT 6628 HB (W2075 x H1290 x T100mm)