Wholesale Interiors BBT 6572 User manual

ASSEMBLY INSTRUCTIONS
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
PLEASE USE THE ABOVE CHECK LIST TO ENSURE ALL HARDWARE IS
INCLUDED.
Tool needed : Screwdriver (not provider).
MODEL : BBT 6572 QUEEN STORAGE BED
PART LIST
ITEM DESCRIPTION QTY
AHEADBOARD 1 PC
BFOOTBOARD 1 PC
CSIDE RAIL 2 PCS
DBED LEG 4 PCS
EHANDLE 2 PCS
FMETAL FRAME 1 SET
GBED SLAT 26 PCS
HPP TAPE 1 PC
IGAS SPRING 2 PCS
JMETAL SUPPORT LEG 1 PC
K2 SMALL ANGLE 2 PCS
LCENTER SUPPORT 1 PC
MHORIZONTAL SUPPORT WOOD 5 PCS
NCENTER SUPPORT LEG 5 PCS
OHEADBOARD SUPPORT WOOD 1 PC
PFOOTBOARD SUPPORT WOOD 2 PCS
QBOTTOM SUPPORT BOARD 4 PCS
PAGE 1 OF 5
HARDWARE LIST
ITEM DESCRIPTION QTY
1JCBB BOLT M8 x 30mm 16 PCS
2BED SLAT SIDE FITTER 26 PCS
3BED SLAT CENTER FITTER 13 PCS
4201 LEG BRACKET 2 PCS
5Wood Screw M3.5 x 16mm 4 PCS
6Wood Screw M4 x 20mm 8 PCS
7PVC BLACK WASHER 2 PCS
8M4 ALLEN KEY (BALL SHAPE) 1 PC
9M5 ALLEN KEY (BALL SHAPE) 1 PC
10 JCBC Bolt M6 x 40mm 6 PCS
11 JCBB Bolt M8 x 40mm 4 PCS
12 JCBB Bolt M8 x 70mm 8 PCS
13 M6 FLAT WASHER 8 PCS
14 M6 SPRING WASHER 8 PCS
15 M8 FLAT WASHER 20 PCS
16 M8 SPRING WASHER 22 PCS
17 M6 HEX NUT 6 PCS
18 M8 HEX NUT 18 PCS
19 SPANNER (10mm) 1 PC
20 SPANNER (13mm) 1 PC
21 SPECIAL HEX NUT 6 PCS
22 JCBC BOLT M8 x 20mm 4 PCS
23 HANDLE SCREW M8 x 70mm 2 PCS
24 JCBC Bolt M6 x 20mm 4 PCS
25 JCBC Bolt M6 x 35mm 5 PCS
26 JCBC Bolt M6 x 60mm 4 PCS
27 JCBC Bolt M6 x 70mm 2 PCS
28 JCBB Bolt M8 x 50mm 4 PCS
x4
STEP B
BACK VIEW
STEP A
FRONT VIEW
STEP 1
A
9
28
16
15
D(R)
D(L)
4
18
20
16

STEP 2 ASSEMBLY INSTRUCTIONS
Loosely fit bolt (1) into Headboard (A) & Footboard (B) as
picture shown.
A
8
27
7
D
P
8
26
8
25 M
N
B
1
A
1
B
O
PAGE 2 OF 5
x5
x2
9
1
C
D(R)
D(L)
STEP 3
STEP 4
x2
13
14
24
8
C
x2

STEP B STEP D STEP ESTEP C
ASSEMBLY INSTRUCTIONS
A
1
9
C
20
18
16
15 E
8
10
13
17
14
K
19
18
12
15
16
18
15
11
9
16 H
9
F
PAGE 3 OF 5
STEP A
B
C
9
124
13
14
866
STEP 5
STEP 6 STEP 7
STEP A
STEP B
STEP B
STEP A

Palm
G
2
ASSEMBLY INSTRUCTIONS
19 17
J10 8
Palm
G
G
3
STEP C
STEP B
Attention :
A person need to hold up the metal frame from
footboard side,and the other person assemble the gas
spring (Item I).
STEP A
20
21
23
22
M
C
PAGE 4 OF 5
21
21
20
I
STEP 8 STEP 9
STEP 10 STEP 11
x5

Attention :
To ensure your bed frame remains in optimum condition,
please periodically check all the screw and re-thightening if
necessary.
ASSEMBLY INSTRUCTIONS
5
Q
L
PAGE 5 OF 5
STEP 12 STEP 13
STEP 14 STEP 15
Note : Follow the line drawing to assemble the center support.
Attention :
1. Place your mattress onto the bed
frame BEFORE closing or this could
results in damage to the bed
(MATTRESS NOT INCLUDED) .
2. It is imperative that the bed is
aligned squarely to prevent the frame
from catching on and damaging the
upholstered side rails
Please use extra caution when
opening and closing the bed for the
first few times.
Ensure a similar spacing on each side
of the frame.
Ensure open and close the bed frame
thru center of bed by using PP tape
on center of metal frame.