Wildview Xtreme 3 User manual

STC-TGL3M
User’s Manual
Toll Free Customer Support 1-888-304-6125
www.wildviewcam.com
Version 1.1 08/06

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
2
For Customer Service or Warranty Information Call
Toll Free
888-304-6125
WILDVIEW
P.O. Box 535189
Grand Prairie, Texas 75053-5189
www.wildviewcam.com
Wildview Scouting Camera Limited Warranty
Your Wildview Scouting Camera is covered by a One Year
Limited Warranty on parts & labor from the date of purchase.
The warranty covers defects in workmanship & materials.
The warranty does not apply to units, which have been
damaged or abused intentionally or unintentionally.
Tampering with or altering the unit will void the warranty. Any
unauthorized service will void warranty. Original sales receipt
must be produced for any warranty service.
Questions call 888-304-6125.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
3
Manual Contents
Camera overview 4
Camera kit contents 7
Battery and memory Installation 8
Definition 11
Programming 13
Mounting the camera 16
Viewing images 20
Saving and Deleting images 23
Memory compatibility chart 26
Technical Specs 27
General Information 30

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
4
Camera overview
Front view Side view

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
5
Open view image with major parts indication

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
6
Image Capacity Chart
SD card High Low AVI
Built In 32MB
SDRAM
12 33 10
16MB 10 26 8
32MB 20 52 16
64MB 40 104 32
128MB 80 208 64
256MB 160 416 128
512MB 320 832 256
1GB* 640 1664 512
2GB* 1280 3328 1024
* Subject to card compatibility under different brand
NOTE: Picture / Image Capacity Chart provides approximate

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
7
number of images or AVI movies based on resolution setting
and the size of memory card. These figures may vary
depending on the amount of detail in the image.
Camera kit contents
• Model STC-TGL3M Digital Scouting Camera
• Camera driver
• User Manual
• USB cable
• Strap

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
8
Battery & memory installation
The Wildview STC-TGL3M Digital Scouting Camera is
designed to operate using alkaline batteries for optimum
performance.
NOTE: Always have camera in OFF position when
installing or removing batteries.
Batteries “C” cell
The internal battery compartment accepts 4 “C” cell
batteries. Be sure to use high quality brand name
alkaline batteries. Install batteries in correct polarity (+/-)
as noted inside battery compartment.
Warning: Do not use different Voltage lead
acid battery other than the one specified in
this section. Doing so will damage the camera
and will void the warranty.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
9
12V Lead Acid external battery
The STC-TGL3M is equipped with an external power jack
designed to accept a barrel plug cable to attach to a
sealed lead acid battery. (sold separately). Battery cable
and complete 12V Lead Acid battery kits are available
wherever Wildview scouting cameras are sold or call toll
free 888-304-6125. Only Wildview external battery
accessories are recommended.
• Insert the battery pack plug into the DC 12V jack at
the bottom of camera housing
• Turn on the camera by sliding the power switch to
PIR position
Please make sure the voltage and polarity (+/-) are
correct before connection. Incorrect voltage or
polarity (+/-) will damage the camera.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
10
Memory Options
Your Wildview scouting camera is equipped with 32MB
built in SDRAM memory. The camera is also equipped
with an expandable media card slot capable accepting up
to 2GB* SD card (sold separately). With no memory card
inserted into the slot, the camera will use the built in
32MB SDRAM memory. If a SD card is inserted into the
slot then the camera will bypass the built in memory and
utilize the SD memory. The front counter display will
show the number of images on the built in memory
unless the expansion card is inserted at which point the
counter will only show the number of images in the
expansion card.
Inserting SD card
Make sure camera is in the OFF position whenever
adding or removing memory.
• Insert SD memory card in to the SD card slot
completely and in the correct direction as shown on
the inside of the housing.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
11
• To remove the SD memory card, depress the SD
card and pull out the card gently.
 SD cards must be clean (no images from other
sources.)
Definition
• Time out: To set the amount of preset time in
minutes the camera will sleep between PIR triggering
• Resolution: The resolution selection that you have
selected.
o High: Select this option to capture a 3.1M pixel
image quality
o Low: Select this option to capture a 1.3M pixel
image quality
• Date/Time: To set date and time stamp in the picture
• Flash: Auto / On / Off mode

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
12
• Burst: To set number of picture the camera will take
per PIR triggering
o 1P: Single image capturing per PIR triggering
o 2P: Two images continuous capturing per PIR
triggering
o 3P: Three images continuous capturing per PIR
triggering
o AVI: 10 seconds video clip per PIR triggering
• FULL: When memory capacity is full, this front LCD
screen will show “FULL”

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
13
Programming your Wildview Camera
The following setting must be performed before you
turn on the camera.
1. Select the time out interval by sliding the time out
toggle switch to the desire preset time interval in
minutes. 1 / 5 / 10 / 20 minutes.
2. Select the resolution setting by sliding the resolution
toggle switch to the desire resolution setting. Hi / Lo
resolution.
3. Select the Flash mode: Slide the switch to either
Auto / On / Off position.
a. Auto – Flash on based on surround lighting
condition
b. On – Flash on for every image captured
c. Off – No Flash will go off.
4. Select Burst mode: Slide the switch to 1 / 2 / 3 / AVI
position. If you choose AVI mode, the camera will
automatically switch to 1 picture mode if it detect low
light source.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
14
5. Turn on the Camera to set the Date / Time stamp
a. Slide the power switch to PIR position
b. Press and hold [SET] button for 2 seconds to
enter date & time setting mode.
c. Time and HH will blink. Press [UP] or [DN] to
adjust hour
d. Press [SET] button to enter minute setting. Time
and MM will blink. Press [UP] or [DN] to adjust
minute.
e. Press [SET] button to enter month setting. Date
& MM will blink. Press [UP] or [DN] to adjust
month.
f. Press [SET] button to enter date setting. Date &
DD will blink. Press [UP] or [DN] to adjust date.
g. Press [SET] button to enter year setting. Date &
YY will blink. Press [UP] or [DN] to adjust year.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
15
h. Press and hold [SET] button for 2 seconds to exit
the setting mode and into PIR count down mode.
Display will show date and number of picture
taken.
Once the program setting has been completed, slide
the power switch to OFF position until you are ready
for field use.
NOTE: Date & Time setting will be lost whenever battery
is removed from camera. Don’t forget to re-set the Date
& Time stamp after you replace the battery.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
16
Mounting the camera
It is recommended to mount the camera 4-5 ft off the
ground with the camera pointed at a slight downward
angle. Be sure to avoid mounting the camera facing
east or west as the rising and setting of the sun could
produce false triggers and overexposed images. Clear
branches and other debris away from the front of the
camera so as not to block the camera lens or PIR
sensor.
PIR Coverage Area Diagram

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
17
Mounting the camera with the supplied strap
• Insert the strap through the strap slots on the rear
housing.
• Wrap the strap around the mounting surface. Secure
the strap and tighten the buckle in order to secure the
camera.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
18
 In order to obtain proper weather resistance,
please make sure that both door latches are
securely locked in place.
Testing the camera coverage area
One of Wildview Scouting Camera’s features is the ability
to test the coverage area.
• After mounting the camera, open front housing and
slide the power switch to Test position. The front
LCD will display the word “tESt”.
• Close the front housing.
• Walk around in the front of the camera to see if you
have mounted camera in the proper position. A green
indicator light on the front will blink on when you have
intruded the coverage area.
• Adjust the camera position as needed and repeat
testing until the desired coverage area is achieved.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
19
• When you have completed the testing the coverage
area open the front housing and slide the power
switch from Test position to PIR position. Front LCD
counter will show “0000”. The camera will enter
count down mode for 1 minute and front green
indicator will start blinking giving you one minute to
leave the coverage area. Then camera will enter PIR
detection mode.
NOTE: Make sure you slide the power switch from TEST
mode to PIR mode before you leave the field. Otherwise
the Camera will not take any pictures.
Switch use: Do not move the switch from TEST directly
to PIR. Doing so will cause the camera to not operate.
Slide the switch to OFF. Wait for the front LCD screen to
turn off then continue to slide the switch to PIR.

STC-TGL3M
www.wildviewcam.com Toll Free 888-304-6125
20
Viewing images
Viewing images by computer download
The Wildview Scouting Camera is a plug and play USB
storage device. This means users of Windows 2000 /ME
/ and XP operating system need not install the camera
driver. This camera is not MAC compatible. The CD-ROM
included in this package contains the camera driver for
older operating system only.
Attention
The software CD-ROM packaged with the camera is
designed for PC’s only (not MAC compatible). Playing
this CD-ROM on a stereo or CD player may cause
damage to it.
Driver installation
• Unplug the USB cable from PC.
• Insert the CDROM in CD driver of your PC.
• The auto-run program will execute.