Wilson Electronics IoT 5-Band User manual

IoT 5-Band
Direct-Connect Cell Signal Amplifier
Installation Guide

Index
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IoT Retail Application Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
IoT Security Application Steps ..........................................7-10
Status Light Patterns ....................................................11
Safety Guidelines ......................................................12
Specifications .........................................................16
Warranty .............................................................17

1
IoT 5-Band
Direct-Connect Cell Signal Amplifier
The WilsonPro IoT 5-Band is a “Direct-Connect” solution for amplifying cellular
network capable equipment and devices, including vending machines, ATMs,
security panels, and cellular “hotspots”. The IoT 5-Band is “carrier agnostic” and pre-
approved by all major cell carriers under FCC “part 20” rules. No additional carrier
or FCC approvals are required.
The IoT 5-band is available in three dierent kit options: 460119: basic kit with
traditional a/c power supply, 460219: with “hard-wired” DC power supply (for
supplying power from a vehicle or similar power source), and the 461119 Security Kit
which includes MMCX cables for interfacing with security control panel cell modems,
and an outside antenna.

2
Package Contents
IoT 5-Band
Cell Signal Amplifier
(460019)
Kit Options (IoT 5-Band Cell Signal Amplifier included)
IoT 5-Band Kit
460119
■6 ft. RG-174 w/SMA
■5V / 4A A/C Power
Supply
■4 in. Mini Magnetic
Antenna
IoT DC Hardwire Kit
460219
■6 ft. RG-174 w/SMA
■6V / 2A Hardwired
Power Supply
■4 in. Mini Magnetic
Antenna
■12 in. RG-316
w/MMcx
■12 in. Adapter
w/MMcx
■10ft. RG-58
w/SMA
■30ft. RG-58
w/SMA
■5V / 4A
A/C Power Supply
■Omni Antenna
IoT Security Kit
461119
Any Kit Option
Below
+

3
STEP 1 Outside Antenna
Placement
Mount the Outside Antenna on top
of a metal structure that is free of
obstructions and 12 in. away from any
other antennas.
Select a location to install the Signal
Amplifier that is away from excessive
heat, direct sunlight, moisture and that
has proper ventilation.
STEP 2 Amplifier Placement
Outside Antenna
5-Band Amplifier
IoT Retail Application Example

4
Run the Outside Antenna Cable to
the Signal Amplifier and attach it
to the connector labeled Outside
Antenna. Finger tighten only.
STEP 3 Route & Connect
Antenna to Amplifier
Outside Antenna
IoT 5-Band
Signal Amplifier
Connect the provided cable to
the cellular device (adapter may
be needed) then to the connector
labeled Data Device on the Signal
Amplifier. Finger tighten only.
STEP 4 Connect Device
to Amplifier
Outside Antenna
IoT 5-Band
Signal Amplifier
Data
Device

5
Plug the Power Supply into an outlet
(or connect to hardwired 12V DC
source if kit 460219 is used) then
connect to end of amplifier
labeled POWER.
STEP 5 Power Up the
Amplifier
Outside Antenna
IoT 5-Band
Signal Amplifier
Power Supply
■If the amplifier loses power, internal circuitry will
bypass the amplifier switch so that a connection
is made directly to the antenna.
■Safeguard your devices. Using a surge
protector is always recommended for these
applications.
Important
Modem
IoT 5-Band
Amplifier Antenna
IoT 5-Band
Signal Amplifier
Data
Device

6
Outside Antenna
Diagram
Cellular Modem
IoT 5-Band
Amplifier
Power Supply
Surge Protector

7
STEP 1 Outside Antenna
Placement
Mount the Outside Antenna on top
of a metal structure that is free of
obstructions and 12 in. away from
any other antennas.
Select a location to install the Signal
Amplifier that is away from excessive
heat, direct sunlight, moisture and that
has proper ventilation.
STEP 2 Amplifier Placement 5-Band
Amplifier
IoT Security Application Example Omni Outside
Antenna

8
When using the Omni Outside
Antenna, connect the N-Type
connector to the antenna, then
the SMA end to the amplifier.
Finger tighten only.
STEP 3 Route & Connect
Antenna to Amplifier
IoT 5-Band
Signal Amplifier
Connect the provided MMCX
cable to the Security Control Panel
(adapter may be needed) then to
the connector labeled Data Device
on the Signal Amplifier.
STEP 4 Connect Device
to Amplifier
Omni Outside
Antenna
Omni Outside
Antenna
IoT 5-Band
Signal Amplifier Security
Control Panel

9
Connect the provided cable to the
Security Control Panel (adapter may
be needed) then to the connector
labeled Data Device on the
Signal Amplifier.
STEP 5 Power Up
the Amplifier Omni Outside
Antenna
IoT 5-Band
Signal Amplifier
Security
Control Panel
■If the amplifier loses power, internal circuitry will
bypass the amplifier switch so that a connection
is made directly to the antenna.
■Safeguard your devices. Using a surge
protector is always recommended for these
applications.
Important
Modem
IoT 5-Band
Amplifier Antenna

10
Diagram
Omni Outside
Antenna
IoT 5-Band
Amplifier
to AC power
Security
Control Panel
10 ft. RG58
30 ft. RG58

11
GREEN
This indicates that your amplifier is functioning properly and there are no issues
with installation.
SOLID RED
Band has shuto. This is due to a feedback loop condition called oscillation. This is
a built in safety feature that causes a band to shut o to prevent harmful interference
with a nearby cell tower. Refer to Troubleshooting section.
BLINKING GREEN, RED
This indicates that the amplifier is operating at a reduced gain to prevent
oscillation (feedback).
LIGHTS OFF
If the Signal Amplifier’s light is o, verify your power supply has power.
Status Light Patterns

12
FIXING RED LIGHT ISSUES
This involves Solid Red & Blinking Green/Red lights.
■ Make sure all connections are tight. Un-plug and re-plug in power supply.
■ Increase the distance (horizontally or vertically) between the Outside Antenna and
the amplifier. Un-plug and re-plug in power supply.
LIGHTS OFF
■ Check connections on the power supply to see that it is firmly plugged into both
the amplifier and the power source.
Troubleshooting
866.294.1660 www.wilsonelectronics.com [e-mail]

13
Safety Guidelines
Verify that both the Outside Antenna and the adapter extension cable are connected to the Signal Amplifier
before powering up the Signal Amplifier.
Use only the power supply provided in this package. Use of a non-Wilson Electronics products may damage
your equipment.
RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons.
AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”) above ground
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most
wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on
their network. If you are unsure, contact your provider.
In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.
You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be
installed at least 20 cm (8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC (or ISED in Canada) or licensed wireless
service provider.
WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.
This device may be operated ONLY in a fixed location (i.e..may operate in a fixed location only) for in-building use.

14
Safety Guidelines (cont.)
FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS
PROVIDER, PLEASE SEE BELOW:
Sprint: http://www.sprint.com/en/legal/signal-boosters.html?=search:booster
T-Mobile/MetroPCS: https://support.t-mobile.com/docs/DOC-9827
Verizon Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05, SEE BELOW:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html

15
Antenna Info
ΩAntenna TypeCoax Type# Ln(ft)
50Omni PlusRG-58304422 30
OUTSIDE ANTENNA INFO
Outside antenna maximum permissible
antenna gain (dBi) 50Ω 4.743.714.464.24.5
BAND 25/2BAND 4BAND 5BAND 13BAND 12/17
The following accessories are certified by the FCC to be used with the IoT 5-Band Direct-Connect
Cell Signal Amplifier.
This radio transmitter 4726A-460019 has been approved by Innovation, Science and Economic Development
Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna
types not included in this list that have a gain greater than the maximum gain indicated for any type listed are
strictly prohibited for use with this device.
50Mini-MagLMR-100301126 10

16
460019
PWO460019
4726A-460019
SMA
50 Ohms
4 dB (nominal)
> 40 dB
5V, 4A
700 MHz B12/17
24.6
-6.3 -6.1 -6.5 -6.8 -6.7
700 MHz B13
24.9
800 MHz B5
23.9
1700 MHz B4
23.9
1900 MHz B2
23.5
698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz
Model
FCC
IC
Connectors
Antenna Impedance
Frequency
Noise Figure
Isolation
Power Requirements
Power output for single cell
phone (Uplink) dBm
Power output for single cell
phone (Downlink) dBm
IoT 5-Band Direct-Connect Cell Signal Amplifier
Specifications
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Each Signal Amplifier is individually tested and
factory set to ensure FCC compliance. The Amplifier cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Amplifier will amplify, but not
alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Amplifier is not in use for five minutes, it will reduce
gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Amplifier detects an oscillation, the Signal Amplifier will automatically
turn the power off on that band. For a detected oscillation the Signal Amplifier will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such
automatic restarts, any problematic bands are permanently shut off until the Signal Amplifier has been manually restarted by momentarily removing power from the Signal
Amplifier. Noise power, gain, and linearity are maintained by the Signal Amplifier’s microprocessor. This device complies with Part 15 of FCC rules. Operation is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation. Changes or modifications not expressly approved by Wilson Electronics LLC could void the authority to operate this equipment. This device contains license-
exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the
device. Changes or modifications not expressly approved by Wilson Electronics LLC could void the authority to operate this equipment.

17
DISCLAIMER: The information provided by Wilson Electronics, LLC is believed to be complete and accurate. However,
no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from its use, or for any
infringements of patents or other rights of third parties that may result from its use.
MARKETING APPROVAL: Installer and end customer hereby grants to Wilson Electronics the express right to use
installers or end customers company logo in marketing, sales, financial, and public relations materials and other
communications solely to identify Customer as a Wilson Electronics customer.
30 DAY MONEY-BACK GUARANTEE
All WilsonPro products are protected by WilsonPro 30-day money-back guarantee. If for any reason the
performance of any product is not acceptable, simply return the product directly to the reseller with a dated
proof of purchase.
3 YEAR WARRANTY
WilsonPro Amplifiers are warranted for three (3) years against defects in workmanship and/or materials. Warranty
cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
Signal Amplifiers may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of
purchase and a Returned Material Authorization (RMA) number supplied by WilsonPro. WilsonPro shall, at its option,
either repair or replace the product.
This warranty does not apply to any Signal Amplifiers determined by WilsonPro to have been subjected to misuse,
abuse, neglect, or mishandling that alters or damages physical or electronic properties.
Replacement products may include refurbished WilsonPro products that have been recertified to conform with
product specifications.
RMA numbers may be obtained by contacting Customer Support.

NOT AFFILIATED WITH WILSON ANTENNA GDE000209_Rev03_12.11.19
3301 East Deseret Drive, St. George, UT
866.294.1660 www.wilsonelectronics.com [e-mail]
Copyright © 2019 Wilson Electronics. All rights reserved. Wilson Electronics products covered by U.S. patent(s) and pending
application(s) For patents go to: weboost.com/us/patents