WilTec 62557 User manual

Operation Manual
Styrofoam Cutter
62557, 62564
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

© by WilTec Wildanger Technik GmbH Item 62557 Page 2
http://www.WilTec.de
http://www.aoyue.eu 05 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: [e-mail]
Tel:[phone]
Fax: [phone]
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [email protected]o
Tel:[phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 62557 Page 3
http://www.WilTec.de
http://www.aoyue.eu 05 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
•Easy cutting of expanded polystyrene (EPS) foam, expanded polyethylene (EPE) foam and
similar materials without chipping.
•Capable of cutting grooves that are ideal for placing pipes, when used with the smaller grooving
plate (G01).
•When used in combination with the grooving plate (G02), the polystyrene cutter is capable of
performing a wide variety of different cutting methods, such as effortlessly creating grooves.

© by WilTec Wildanger Technik GmbH Item 62557 Page 4
http://www.WilTec.de
http://www.aoyue.eu 05 2021-1
http://www.teichtip.de
Optional Accessories
Accessory
Image
Purpose
30 cm flexible blade (B05)
Used for EPS and EPE foams,
sponges and similar material.
Grooving plate (G01)
Used for cutting grooves into
EPS and EPE foams, sponges
and similar materials.
Grooving plate (G02)
Used for cutting grooves into
EPS and EPE foams, sponges
and similar materials.
Cutting guide (G04)
A cutting guide allowing for easy
and precise cuts and bevelling.
Cutting procedure
1. Set the device temperature to a middle temperature, attach the accessory that you wish to use
and turn on the power switch. Laymen should perform a few test cuts on spare material in order
to get used to the handling of the tool.
Beware! The blade of the polystyrene cutter heats up very quickly.
2. The device temperature controller offers 16 different temperature settings that can be checked
due to a visible line; the longer this line, the higher the output voltage.
3. Always make sure that the temperature is adjusted to the cutting speed. An excessive emission
of smoke may be caused by overheating or a low cutting speed and may lead to irregular cuts.
Adjust the operating temperature or take breaks between cuts.
4. Use the copper brush to remove residue from the blade after every use of the device.
Safety instructions
•Always make sure that the working area is ventilated before using the device.
•Do not burn off residue located on the blade as this might deform the same.
•Do not touch the blade after it has heated up and do not place a device with a hot blade in the
vicinity of flammable objects or substances.

© by WilTec Wildanger Technik GmbH Item 62557 Page 5
http://www.WilTec.de
http://www.aoyue.eu 05 2021-1
http://www.teichtip.de
•Allow the blade to cool down before touching it after use in order to avoid burns.
•When using the device make sure to maintain an adequate cutting speed and operating tem-
perature as overheating might cause damage to the device and its accessories.
•Release the trigger for 1 s after 30 s of operation time.
Technical specifications
Output (W)*
100
150
200
250
Voltage (V)
230
Frequency (㎐)
50
Blade temperature (℃)
up to 600 (after 5–8 s)
Cable length (m)
3
Blade length (㎜)*
100
150
200
250
Additional accessories
Hex key / copper brush
* Both the output and the blade length depend on the model and type of your device.
Blade installation
1. Use the hex key included in the scope of delivery in order to loosen the screw of the copper
fastener.
2. Insert the blade into the fastener and fasten the screw. Make thereby sure that there is enough
contact for the blade to function properly.
3. Reverse the process in order to remove the blade. It is thereby essential to allow the device to
cool down properly before removing or exchanging the blade in order to avoid burns.

© by WilTec Wildanger Technik GmbH Item 62557 Page 6
http://www.WilTec.de
http://www.aoyue.eu 05 2021-1
http://www.teichtip.de
Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were imple-
mented in the law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.
The company WilTec Technik GmbH has been registrated in the German registry EAR under the WEEE-
registration number DE45283704.
Disposal of used electrical and electronic appliances
(intended for use in the countries of the European Un-
ion and other European countries with a separate col-
lection system for these appliances).
The logo on the article or on its packaging points out
that this article must not be treated as normal house-
hold waste but must be disposed to a recycling collec-
tion point for electronic and electrical waste equipment.
By contributing to the correct disposal of this article you
protect the environment and the health of your fellow
men. Environment and health are threatened by inap-
propriate disposal.
Material recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal waste
disposal facilities or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.