WilTec toboli 61183 User manual

Operation Manual
Sausage stuffing machine
61183
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

© by WilTec Wildanger Technik GmbH Artikel 61183 Seite 2
http://www.toboli.com 05 2022-1
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
To return orders for exchange, repair, or other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Artikel 61183 Seite 3
http://www.toboli.com 05 2022-1
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
Safety instructions
•Improper operation may result in damage to the unit or injury. No responsibility is accepted for
damage caused by improper operation.
•Only use the sausage machine as intended. The machine is intended exclusively for the prep-
aration of sausage. Any improper use may result in property damage and injury.
•Do not use the sausage machine if it is damaged or its functionality is restricted. In this case,
have the machine checked by qualified personnel.
•Never open the casing of the machine.
•Do not insert any objects into the machine housing.
•Only use approved spare parts. The use of unsuitable spare parts can cause damage to prop-
erty and injuries.
•Never leave the machine unattended during operation.
•Keep children away from the machine.
•The machine must not be used by persons, including children, with reduced physical or mental
capabilities or persons without appropriate knowledge and experience.
Operation
1. Rinse the parts that come into contact with the food well.
2. Place the sausage machine on a flat and stable surface.
3. Attach the hand crank to the fast gear shaft (see fig. 1) and turn the crank clockwise to raise the
piston.
1. Place the nozzle on the spout and secure it with a lock nut.
2. It is recommended to apply food grade grease (not supplied) before filling. Then fill the cylinder
with meat and place the sausage pellet on the nozzle.
3. Attach the hand crank to the slow gear shaft (see fig. 1) and turn it slowly clockwise to lower the
piston. The meat is now fed through the nozzle into the sausage pellet and the sausage is
formed.
Caution! If the meat does not come out of the nozzle, make sure that there is no blockage. Remove
possible blockages and make sure that the degree of mincing of the meat is sufficient for the selected
nozzle.
(1) Fast gear shaft; (2) Slow gear shaft
Figure 1

© by WilTec Wildanger Technik GmbH Artikel 61183 Seite 4
http://www.toboli.com 05 2022-1
Cleaning and care
•Clean all parts in contact with food (e.g., cylinder, nozzle, piston, etc.) with a soft brush or cloth.
Use a cleaning agent approved for use with meat processing equipment.
•Clean the outside with a damp cloth and a mild detergent.
•Do not use aggressive cleaning agents, solvents or scouring agents and do not attempt to clean
the appliance with sharp or pointed objects.
•Make sure that all parts are dry before reassembling the sausage machine.
Storage and maintenance
•Store the sausage machine in a clean, dry, and well-ventilated place without direct sunlight.
•Do not expose the machine to rain.
•Apply some food grade grease to the gear system about every 6 months.
•Replace the piston seal as necessary (about every 6 months).
Exploded view and parts list
№
Name
Qty
№
Name
Qty
1
Left panel
1
15
Gear
1
2
Nut
4
16
Axle of small gear
1
3
Inner hexangular nut
4
17
Hand crank
1
4
Stainless steel screw
4
18
Axle of big gear
1
5
Nozzle
4
19
Gear base
1
6
Front ring nut
1
20
Base plate
1
7
Base plate
1
21
Stainless steel cross screw
4

© by WilTec Wildanger Technik GmbH Artikel 61183 Seite 5
http://www.toboli.com 05 2022-1
8
Stainless steel screw
4
22
Stainless steel cross screw
1
9
Right panel
1
23
Piston
1
10
Stainless steel cylinder
1
24
Piston seal
1
11
Piston rod
1
25
Spring
1
12
Gearbox cover
1
26
Vent pin
1
13
Hexangular bolt
4
27
Elastic pin
2
14
Stainless steel cross screw
8
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.