WilTec 61947 User manual
Operation Manual
Automatic Pool Cleaning Robot
61947
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
© by WilTec Wildanger Technik GmbH Item 61947 Page 2
http://www.WilTec.de
http://www.aoyue.eu 12 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: service@wiltec.info
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
© by WilTec Wildanger Technik GmbH Item 61947 Page 3
http://www.WilTec.de
http://www.aoyue.eu 12 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
Safety precautions
•This device is not intended to be used by persons (or children) with reduced physical, sensory,
or mental capabilities or persons not having the necessary experience or knowledge, unless
they are supervised by a person responsible for their safety or have previously been instructed
in the use of the device.
•The floor cleaner must not be used when there are people in the pool.
•The floor cleaner must be removed from the pool after use.
•Remove the connection to the filter pump before cleaning the floor cleaner.
•Do not play with the device – risk of drowning!
•Make sure that the floor around the pool is dry – risk of slipping!
Parts list
№
Name
№
Name
1
Pedestal
6
Suction manometer
2
Border
7
Flow rate regulator
3
Main body
8
Universal adaptor
4
Guide wheel
9
Hose weight
5
Hose segments
10
Membrane
© by WilTec Wildanger Technik GmbH Item 61947 Page 4
http://www.WilTec.de
http://www.aoyue.eu 12 2021-1
http://www.teichtip.de
Exploded view and parts list
№
Name
№
Name
1–5, 9
(see above)
306
Bushing
301
Clamp
307
Washer
302
Membrane
308
External tube
303
O-ring
309
C-ring
304
Housing
310
Nut
305
Inner tube
Assembly and replacement of membranes
Important note! Before the pool cleaner is connected to the filtration system, the product must be sub-
merged to avoid air suction. The hoses must be filled with water. Adjust the flow regulator to get the best
performance from the cleaner.
© by WilTec Wildanger Technik GmbH Item 61947 Page 7
http://www.WilTec.de
http://www.aoyue.eu 12 2021-1
http://www.teichtip.de
Troubleshooting
Problem
Proposal for solution
The cleaner starts and stops or does not
move.
Make sure that filter is clean and pump is switched on.
Switch off safety suction; make sure that main drain is closed.
Make sure that vacuum plate is properly installed.
Check if cleaner and hose are free from air pockets.
Check membrane for damage or blockages.
The cleaner misses spots in the pool.
Make sure that correct amount of hose has been installed; try
adding or removing a length of tubing or two.
Make sure that all returns direct flow of water to pool floor;
adjust balls or use water distributor.
Make sure that hose is straight and not tangled.
The cleaner does not rise.
Make sure that pool water is properly balanced; a high pH
and/or lack of chlorine make walls very slippery.
Increase suction with flow regulator.
Check that float arm is in correct position. Note: Cleaner can-
not climb up in pools with sharp 90-degree angle between
wall and floor.
The cleaner is taking too long to climb
walls or get out of the water.
Reduce suction power using flow control.
Adjust supplied hose weight towards cleaning head.
Presence of cleaning sticks in the cor-
ners, under the ladders, under the lights
or on the steps of the pool.
Make sure that correct amount of hose has been installed, try
adding or removing a length of tubing or two.
Make sure that all returns direct flow of water to pool floor;
adjust balls or use water distributor.
Add optional hose motors and/or replace wheel deflector with
a larger one.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.
Table of contents
