SAFETY
The following symbols are used throughout this
guideas indicatedintheir descriptions:
HAZARD
INTENSITY LEVEL
Therearethree levelsof hazardintensityidentified
by signalwords
-
WARNING,CAUTION and
FOR
SAFETY.
The level of hazard intensity is deter
-
minedby thefollowingdefinitions:
WARNING
-
Hazards or unsafe practices which
COULDresult insevere personal injuryor death.
CAUTION
-
Hazardsor unsafe practiceswhich could
result
in
minor personal injury or product or property
damaae.
FOR SAFETY:
To Identify actions which must be
followedfor safe operationof equipment.
The following information signals indicate potentially
dangerous conditions to the operator or equipment.
Readthis guidecarefully. Knowwhen these conditions
can exist. Locate all safety devices on the machine.
Reportmachinedamageorfaultyoperationimmediate
-
ly. Do not usethe machine
if
it is not proper operating
condition.
For SAFETY:
DO
NOT OPERATEMACHINE:
0
UnlessTrainedand Authorized
0
Unless Operation Guide is Readand
In
Flammableor Explosiveareas.
Go slow on grades and slippery
Usecare when backingmachine.
Do not carry riderson machine.
Alwaysfollow basicsafety and
traffic rules.
understood.
WHEN USINGMACHINE:
surfaces
.
0
0
0
0
0
BEFORE LEAVING OR SERVICING
MACHINE:
0
Stopon level surfaces.
0
Turn off machine.
WHENSERVICING MACHINE:
0
Avoid movingparts. Do notwear loose
jackets, shirts, or sleeves when workingon
machine.
Block machinewheels beforejacking
machineup.
Use hoistor jack of adequate capacity
to
liftmachine.
UseWindsor approved replacement parts.
0
0
0
WHENTRANSPORTINGMACHINE
INA TRAILER:
0
Make sure the rampangle
is
no more than
Make sure ramp
is
cleanand dry.
Remove squeegeeassembly
&
brushes
before loading.
Align the machineon a levelsurface ten
(10)
feet behindthe ramp.
Push machine up ramp carefully.
Securelvfastenthe machineto the trailer.
lo",
andthe ramp isstrong enoughto
support the machine.
0
0
Put ramp into position.
0
0
0
0
~
THISPRODUCT IS FOR COMMERCIAL
USE
ONLY.
EL
ECTRICA
L:
Inthe USAthisscrubber operatesonastandard15amp
11
5
voltA.C. powercircuit(120V nominal). Specialvoltage mod
-
els are available for international applications. The amp,
hertz, and voltageare listedonthe datalabelfound oneach
machine. Usingvoltagesabove
or
belowthose indicatedon
the data labelwill causeseriousdamageto the motors.
GROUNDINGINSTRUCTIONS:
This appliancemust begrounded.
If
itshouldmalfunctionor
breakdown, groundingprovidesapathofleastresistance
for
electric currentto reducethe risk of electric shock. This ap
-
plianceisequippedwithacordhavinganequipment-ground-
ingconductorandgroundingplug.The plugmustbeinserted
into an appropriate outlet that is properly installed and
grounded
in
accordancewithalllocalcodesandordinances.
Improper connectionof the equipment
-
grounding con
-
ductor can result in a risk of electricshock. Check with
a qualified electrician or service person if you are in
doubt asto whether the outlet is properly grounded.
Do
notmodifythe plugprovidedwiththeappliance
-
ifitwill
notfit the outlet,have
a
properoutlet installedby a qual
-
ifiedelectrician.
This appliance is for use on a nominal 120
-
voltcircuit, and
hasagroundedplugthat lookslikethe plugin
"
Fig.
A
"
below.
A temporary adaptor that looks like the adaptor in
"
Fig.
C
belowmaybeusedtoconnectthisplugtoa2
-
polereceptacle
as shown in
"
Fig. B" below. The temporary adaptor should
be usedonly untila properlygrounded outlet (Fig.A) canbe
installed by a qualified electrician. The green colored rigid
ear, lug,or the likeextendingfrom the adaptor must becon
-
nectedto a permanent ground such as a properly grounded
outlet box cover. Whenever the adaptor is used, it must be
held
in
placeby a metalscrew.
NOTE: Check local electrical codes before using an
adaptor. Adaptors are not allowed in Canada.
4
TCPOE
98447 7/1/97
