Winegard TRAV'LER RP-SK01 Series Guide

Automatic Multi-Satellite TV Antenna
LNB Replacement Instructions
Models RP-SK01, RP-SK05, RP-SK09,
RP-SK73, RPSK01H
For help, email [email protected]
or call 1-800-788-4417
www.winegard.com/mobile
2452261
Rev2 9/18
NOTE: RPSK01H LNB Replacement is only
compatible with SK-1000 built after 1/1/2018.

RAISING THE ANTENNA
1. Press and hold “POWER” for two seconds to turn on the interface box. Wait until
the interface box finishes “connecting to antenna.” The TRAV’LER®antenna may
enter the search routine after ten seconds.
Pay attention to the pinch points as the antenna raises!
2. Wait until the antenna has at least raised to a position in which the feed arm is
parallel to the roof. Then, press “POWER” and “SELECT” at the same time. The
antenna should stop moving.
3. Unplug the interface box. Continue with instructions for your model of
replacement LNB.
RP-SK01 DISH®1000 / RPSK01H HYBRID
LNB REPLACEMENT
1. Remove and set aside the two screws
from the wider end of the underside of
the integrated adapter.
2. Carefully slide the LNB out from
the integrated adapter. Disconnect
the three cables from the LNB using
a 7/16” wrench.
3. RP-SK01- Connect the three cables
running through the integrated adapter
to ports 1–3 (in any order) on the
replacement LNB. Tighten each cable until fingertight, and then use a 7/16”
wrench to tighten a quarter turn more.
RPSK01H – Using the supplied dual coax cable, connect the ends with red heat
shrink wrapping to Port 1 on LNB and Port C on TRAV’LER turret. Connect the
black coax cables to Port 2 on LNB and Port A on TRAV’LER turret.
THE HOPPER 3 AND ALL COMPONENTS MUST CONNECT TO PORT C
ON TRAV’LER BASE. PORT A AND B WILL NOT BE USED FOR REGULAR
CONFIGURATIONS.
Tighten each cable until fingertight, and then use a 7/16” wrench to tighten a
quarter turn more.
4. Slide the LNB into the integrated adapter, and re-install the two screws (removed
earlier) through the integrated adapter and LNB.
Screws removed
from integrated adapter
LNB slid out from
integrated adapter
Integrated
adapter

RP-SK05 DIRECTV®SLIMLINE LNB REPLACEMENT
1. Remove and set aside the four nuts and
bolts holding the LNB guard to the feed
arm. Then, slide the LNB guard down the
feed arm and toward the reflector.
2. Remove and set aside the two screws
holding the LNB to the feed arm.
3. Carefully slide the LNB out from the feed
arm. Disconnect the four coax cables from
the LNB using a 7/16” wrench.
4. Connect the four coax cables running
through the feed arm to the replacement
LNB. The coax cables can be connected in any order. Tighten the cables until
fingertight, and then use a 7/16” wrench to tighten a quarter turn more.
5. Slide the LNB into the feed arm, and re-install the two screws (removed earlier)
through the underside of the feed arm and replacement LNB. Tighten.
6. Slide the LNB guard up the feed arm and over the LNB. The front of the LNB
guard should be ~½” in front of the LNB and should not be touching the LNB.
Install the four bolts through the four holes in the LNB guard. Thread a nut onto
each bolt, and tighten.
RP-SK09 DIRECTV®SWM SLIMLINE
LNB REPLACEMENT
1. Remove and set aside the four nuts
and bolts holding the LNB guard to
the feed arm. Then, slide the LNB
guard down the feed arm and toward
the reflector.
2. Remove and set aside the two screws holding
the LNB to the feed arm.
3. Carefully slide the LNB out from the feed arm.
Disconnect the coax cable from the LNB using
a 7/16” wrench.
4. Connect the coax cable running through the feed arm to the replacement LNB.
Tighten the cable until fingertight, and then use a 7/16” wrench to tighten a
quarter turn more.
5. Slide the LNB into the feed arm, and re-install the two screws (removed earlier)
through the underside of the feed arm and replacement LNB. Tighten.
Screws holding
LNB to feed arm
Bolts holding
LNB guard
to feed arm
LNB guard
Bolts holding
LNB guard
to feed arm
Feed arm
Screws holding
LNB to feed arm
Front of
LNB guard

6. Slide the LNB guard up the feed arm and over the LNB. The front of the LNB
guard should be ~½” in front of the LNB and should not be touching the LNB.
Install the four bolts through the four holes in the LNB guard. Thread a nut onto
each bolt, and tighten.
RP-SK73 SHAW DIRECT
LNB REPLACEMENT
1. Remove and set aside the four nuts and bolts
holding the LNB guard to the feed arm. Then,
remove the LNB guard from the feed arm.
2. Remove and set aside the screw holding the
LNB to the feed arm.
3. Disconnect the four coax cables from the LNB
using a 7/16” wrench, and carefully remove the
LNB from the feed arm.
4. Connect the four cables running through the
feed arm to the four ports on the replacement LNB. The cables can be connected
in any order. Tighten each cable until fingertight, and then use a 7/16” wrench to
tighten a quarter turn more.
5. Slide the LNB into the feed arm, and re-install the screw (removed earlier) through
the underside of the feed arm and replacement LNB. Tighten.
6. Slide the LNB guard onto the feed arm and over the LNB. The front of the LNB
guard should be ~½” in front of the LNB.
7. Install the four bolts through the four holes in the LNB guard. Thread a nut onto
each bolt, and tighten.
STOWING THE ANTENNA
1. Plug in the interface box.
2. Press and hold “POWER” for two seconds to turn on the interface box. Then,
press the Power button again to stow the antenna.
Four coax cables
connected to LNB
Bolts holding LNB
guard to feed arm
Screw holding
LNB to feed arm
Disclaimer: Although every effort has been made to ensure that the information in this manual is correct and complete, no company
shall be held liable for any errors or omissions in this manual. Information provided in this manual was accurate at time of printing.
DISH is a registered trademark of DISH Network L.L.C. DIRECTV is a trademark of AT&T Intellectual Property and/or AT&T affiliated
companies. Shaw Direct is a trademark of Shaw Satellite G.P. TRAV’LER, and Winegard are registered trademarks of Winegard Company.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
1-800/788-4417 • FAX [phone] • www.winegard.com • Printed in U.S.A. • ©2012 Winegard Co
Rev2 9/18 2452261