Winner Cardio Concept magnetic User manual

2
EXPLODE PICTURE
12
35
34
31
36
30
37

3
PARTS LISTS
NO
DESCRIPTION
QUANTITY
1
COMPUER
1PC
2
PULSE SENSOR
1SET
3
FOAM GRIP FOR HANDLEBAR
1SET
4
HANDLEBAR
1PC
5
T-KNOB FOR HANDLEBAR
1PC
6
BOLT FOR FIXING HANDLEBAR
1PC
7
CARRIAGE SCREW
1PC
8
ROUND-HEADED SCREW
6PCS
9
SPRING WASHER
2PCS
10
FLAT WASHER
2PCS
11
METAL COVER FOR HANDLEBAR
1PC
12
REAR COVER FOR COMPUTER
1PC
13
HANDLEBAR POST
1PC
14
SCREW FOR FIXING HANDLEBAR POST
4PCS
15
WASHER FOR FIXING HANLEBAR POST
4PCS
16
SADDLE
1PC
17
SEAT SLIP SET
1PC
18
FLAT WASHER
1PC
19
KNOB FOR SADDLE
1PC
20
SEAT POST
1PC
21
KNOB FOR SEAT POST
1PC
22
NUT FOR REAR&FRONT STABILIZER
4PCS
23
WASHER FOR REAR&FRONT STABILIZER
4PCS
24
PEDAL
1SET
25
FOOT CAP FOR REAR STABILIZER
1SET
26
BOLT FOR FRONT&REAR STABILIZER
4PCS
27
REAR STABILIZER
1PC
28
FRONT STABILIZER
1PC
29
TRANSPORT WHEEL
1SET
30
RIGHT COVER
1PC
31
COMPUTER CABLE (DOWN)
1PC
32
COVER FOR HANDLEBAR POST
1PC
33
CRANK ARM
2PCS
34
COMPUTER CABLE (UP)
1PCS
35
FRONT COVER FOR COMPUTER
1PCS
36
LEFT COVER
1PCS
37
COVER FOR CRANK ARM
2PCS

4
STEP I.
1. Assemble the front (28) and rear (27) stabilizer to the base
post with 4 bolts (26) wave washers (23) and 4 nuts (22).
2. Assemble the left (24) pedal onto left crank and assemble right
pedal (24) onto right crank.
30
37
36

5
STEP 2.
1. Assemble the seat (16) to the seat slip set (17) and use the
knob for saddle (19) and one flat washer (18) , tighten it.
2. Put the plastic sleeve (36) for seat upright into the base post.
3. Put the seat post (20) into the base post.
4. Put the knob for seat post (21) into the hole of base post and
tighten it.
21

6
STEP 3.
1. Assemble the cable of the exercise computer 1 (34) and the
cable 2 (31) between the main frame and handlebar post as
shown in the right picture. Make sure the assemble is tightness.
2. Assemble the handlebar post (13) to the main frame after the
above one step. Fasten those 4 screws(14) and 4 bend washers
(15) .
3. Assemble the cover (32)for handlebar post (13) onto the
handlebar post and main frame.

7
STEP 4.
1. Assemble the handlebar (4) on the handlebar fixture and put
the metal cover (11) on the top of handlebar, just put all
together with flat washer (10) spring washer (9) and two
screw (6&7) and fix it a little bit.
2. Please do not screw too tight at this moment. And then put
the T-knob (5) into handlebar.
3. Assemble the computer (1) to the computer board with four
screws .

8
STEP 5.
1. Assemble the bracket for front cover for computer (12) & rear
cover for computer with 6 round-headed screws. Tighten the
T-KNOB.
35

9
Training Computer
Button Function
MODE : press this button to select function.
RESET :To reset the value of “Tome”,”Distance”, “Calories”,
“Pulse”and “Watt”.
Keep pressing this button for 3 seconds,all the
value on display will reset to zero and LCD display will go
vack to the original face with word “U1” keeping flashing.
ST/STOP : To start or stop the exercise program.
UP : To select the functions upwards for display or
preseting by using this
button.
DOWN : To select the functions downwards for display or
preseting by use this
button.
RECOVERY: To display your heart rate status after exercise with
grade from F1 to F6. F1 is the best and F6 is the
worst.
Function Description:
SPEED : To display current speed with range from 0.0 to 99.9
km/h.
RPM : To display current Rpm(Repetition per minute) with
range from 20 to 999 rpm.
TIME : Count-Up : To accumulate total working time from
zero up to 99.59 min:sec
Count-Down: To count time backwards from preset
value down to zero.
DISTANCE : Count-Up : To accumulate total working distance

10
from zero up to 99.59km
Count-Down: To count the distance backwards from
preset value down to zero.
WATT : To display the power value which the user is working
on.
Rangeis from 0 to 999 watts.
CALORIES: Count-Up : To accumulate total calorie
consumption from zero up to 9999 cal.
Count-Down : To count the calorie backwards from
preset valdown to zero.
PULSE : To display current heart rate figures.with preset heart
rate value,as soon as the actual heart
rate reaches the preset value,the
computer will beep to remind you to
stop exercise.
Functions
Display Range
Preset Range
SPEED
0.0 ~ 99.9 km/h
None
RPM
20 ~ 999 rpm
None
TIME
00.00 ~ 99.59
min:sec
01:00 ~ 99:00
min:sec
DISTANCE
0.00 ~ 99.99 km
0.50 ~ 99.50 km
WATT
0 ~ 999 watts
0 ~ 350 watts
CALORIES
0 ~ 9999 cal
0 ~ 9990 cal
PULSE
30 ~ 240 bpm
30 ~ 240 bpm
RECOVERY
F1 ~ F6
None

11
Step 1
1. Lnstall the batteries into the battery box on back side of the
computer.
2. The LCD will show first the figure “78.0”,then switch to the main
display with the word “U1” flashing. “78.0” is the wheel
circumference for this ergometer preset in the software. “U1”
means user 1. Altogether,this computer allows 4 users to have
memory feature for preset function value in last exercise
program. For the second and later users,you may use “UP”
button to select “U2”, “U3” and “U4”. Press the “MODE” button to
finalize this function.
Step 2
1. On the main display,the words “P”, “MANUAL”, “PROGRAM”,
“USER” and “TARGET H.R.” is flashing.( “P” means pause)
2. Use “Up” and “Down” buttons to select one of them for your
program.press “MODE” button to finalize this function.
Step 3
1. If you select “MANUAL”,use “UP” and “DOWN” button to select
the load level.there are altogether 16 level for the brake system
in this computer.press “MODE” button to finalize this function.
2. “TIME” is flashing.use “UP” and “DOWN” buttons to set your
taget exercise time. If do not intend to set distance, just press
the “MODE” button again.
3. “DISTANCE” is flashing.use “UP” and “DOWN” buttons toset
your taget distance.if you do not intend to set distance,just press
the “MODE” button again.
4. “CALORIES”is flashing. Use “UP” and “DOWN” buttons to set
your taget calorie consumption.if you do not intend to set
calories,just press the “MODE” button again.
5. “WATT” is flashing. Use “UP” and “DOWN” buttons to set your
taget watt. Only in the “MANUAL” mode,you are able to set the
taget “WATT”.if you do not intend to set watt,just press “MODE”
button again.
6. “PULSE” is flashing. Use “UP” and”DOWN” buttons to set your
max.heart rate you may refer to your personal physician for such
information.if you do not intend to set pulse,just press “MODE”
again. So,the monitor will display yours heart rate value only.
7. Now,you may start your exercise program by press the
“ST/STOP” button.

12
STEP 4
1. If you select “PROGRAM”, use “UP” and “DOWN” buttons to
select the program from profile 1 to profile 12. press “MODE”
button to finalize the program profile.
2. Press AGAIN THE “mode” BUTTON”. Then, you are now able to
set your target value for function “ TIME”, “DISTANCE”,
“CALORIES” and “PULSE”. Follow the
Procedure of point(2) to(6) in step 3,you are able to finalize this
program. But in this “PROGRAM” mode,the “WATT” value can
not be preset. Please take notice of this difference.
3. If you do not intend to preset any taget value as illustrated in
point (2),after point (1),do not press “MODE” button.
Instead,press directly the “ST/STOP” button to start your
exercise program.
Step 5
1. If you select “USER” ,use “UP” AND”DOWN” buttons to set up
your own program profile. There are altogether 16 load levels
and 16 load segments in the program.
2. In each segment,after setting the load level,remember to press
again the button of “MODE”. When you have finalized the
program profile,you may decide either go directly for exercise
program by pressing the “ST/STOP” button only onr time
without setting your taget value of the functions. If you intend to
set such target value,press “ST/STOP” button for onr
time,then,press again the same button the second time. In this
moment,the “P” and”TIME” are lashing. You may follow the
same procedure of step 3 to set your target value.
3. Press the “ST/STOP” button to start your exercise program.
Step 6
1. If you select “TARGET H.R.”,use “UP” and “DOWN”buttons to
enter your age first.
2. Press “MODE” button. The “55%” is flashing. Use “UP”
and ”DOWN” buttons to select “55%’,”75%”or “90%” or “THR”.
Press “MODE” button again to finalize it.
3. If you select “55%’,”75%”or “90%”,after pressing “MODE”
button, ”TIME” is flashing. Follow the procedure of step 3,you
may set your taget value of the functions. Press the “ST/STOP”

13
button to start your exercise program.
4. If you select “THR”,after pressing the “MODE” button,the figure
“100” on the LCD of “PULSE” is flashing. Use “UP” and “DOWN”
buttons to set your target heart rate. Press “MODE” again to
finalize it. Press “ST/STOP” button to start your exercise
program.
To go back to the main programs of “MANUAL”, “PROGRAM”,
“USER” or “TARGET H.R.”,you need to stay in “STOP” mode
(Top left area of the LCD shows “P”) and press one time the
“RESET” button. Then, you may use “UP” and” DOWN”
buttons to select the above program modes.
Specia
l Instructions:
1. In “MANUAL” mode,when you have set the “WATT” value,it
becomes a speed independent ergometer. The “WATT” value
which you have preset will be kept the same whatever you
pedaling speed is. That means the tension load will
automatically adjusted according to your pedaling speed to keep
always the same “WATT” value on the monitor.
2. In “TARGET H.R.” mode,when you are pedaling the
ergometer,keep holding the hand-pulse sensor with your 2
hands on the handlebar. The load tension will keep always the
same direction to adjust automatically to let heart rate display
keep up with your actual heart rate. The load level will jump one
step in each 30 seconds, if you actual heart rate is less than the
value shown on the monitor until they are the
Same. then the load level will stay there. If your actual heart rate
is higher than your monitor heart rate ,the load level will drop
one step each time in every 15 seconds until the heart rate are in
the same level. If the load level is already down to the 1st level
and your actual heart rate is still higher than the monitor value,

14
the computer will beep 6 times, after 30 seconds, the computer
function will stop automatically.
3. For a new exerciser to use this ergometer, to reset all the value
which the former user kept in the computer,keep pressing the
“RESET” button for 3 seconds and release. You may start the
program from the beginning.
4. Battery specifications required: 4 pcs of 1.5V SUM 2 battery
5. Without any signal transmitted to the computer for 4 to 5 minutes,
the computer will switch of automatically to conserve the battery
power.