Winners Only DST545024 User manual

WINNERS ONLY
®
ASSEMBLY INSTRUCTIONS
PROD. NO: DST545024
Thank you for purchasing this quality product. Please read instructions thoroughly before unpacking
the assembly parts.
1 OF 2
Caution : Sharp exposed staple tips can cause injury, therefore for your protection, please remove any exposed
staples used in packing.
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with assistance of another person; this will
make the assembly easier, and will help to prevent personal injury and to insure parts are not damaged during
the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come
loose inside the carton during shipping. Please do not discard any packing material until all parts have been
located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residues and rough surfaces and also check for staples or nails left after removing the packing materials.
The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden
plugs may loosen up. They should be periodically inspected and re-tightened to prevent damage to the furniture
and (or) peronal property or cause injury. Always check to be sure all hardware on this list and the below
mentioned components are attached to the furniture properly and kept tightened.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly.
Hardware List:
2
QTYSKETCHDESCRIPTION
NO
1
SIZE
516
"
X 50mm 4 PCS
This product will take 15-20
minutes to assemble
3
Screw driver is require for assembly (not included)
TIP: store the Allen key and or Wrench used in assembly in
this product's drawer or use masking or painter's tape to
affix it to the underside of the product. This will make it
easier to find if you want to periodically tighten bolts or
disassemble the product.
Components List:
B
QTYSKETCHDESCRIPTION
NO
ACUSHION SEAT
1 PC
FRONT LEG
（ RIGHT ）
C1 PC
FRONT LEG
（ LEFT ）
D1 PC
BACK LEG
（ RIGHT ）
E1 PC
BACK LEG
（ LEFT ）
F1 PC
BACK STRETCHER
（ SHORT ）
G2 PCS
SIDE STRETCHER
（ MEDIUM ）
1 PC
H1 PC
FRONT STRETCHER
（ LONG ）
I1 PC
CROSS BAR
（ UPPER ）
5
4
JCBC BOLT
WITH WASHER
M6 X 70mm 4
PCS
8 PCS
WOODEN SCREW
1 PCALLEN KEY
M5 X 32mm
M4
J1 PC
CROSS BAR
（ LOWER)
K3 PCS
CORNER BLOCK
MADE IN MALAYSIA
JCBC BOLT
WITH WASHER
6 PCSWOODEN SCREW M4
X 20mm

Step.3 Turn the chair to a standing position.
Step.4 Check the chairs balance and tighten
all the screws and bolts to complete the
assembly.
A
Screwdriver
(Not included)
Step 1.1 Attach Cross bar upper (I) to Cross bar
lower (J) as shown on FIG 1.1
Step 1.2 Attach all legs (B,C,D,E), insert the
JCBC Bolt with washer (1) into the pre-drilled
holes on the Cross bar (I, J
） into the Leg,
tighten the JCBC Bolt with washer with
Allen Key provided as shown on FIG 1.2
Step 1.3 Secure all Stretchers (F,G,H) to Legs,
using Wooden screw (3), tighten them with
Screwdriver as shown on FIG 1.3
Step 2.1 Insert the JCBC Bolt with washer (2)
into the pre-drilled holes on the Cross bar (I, J)
into the Cushion seat (A), tighten the JCBC Bolt
with washer with Allen Key provided
as shown on FIG 2.1
Step 2.2 Attach Corner block (K) on front and
both sides of the Cushion seat (A) using
Wooden screws (4), tighten them with
Screwdriver as shown on FIG 2.2
K
4
Assembly is now complete.
5
2
Screwdriver
(Not included)
1
J
I
3
C
B
D
E
G
G
H
F
Leveler
FIG 1.1
FIG 1.2
FIG 1.3
FIG 2.1
FIG 2.2
2 OF 2
WINNERS ONLY
®
ASSEMBLY INSTRUCTIONS
PROD. NO: DST545024
5
I
J
I
J