Winners Only T1-VG4260-O User manual

SOLID TOP BUTTERFLY LEAF PEDESTAL TABLE
PART NO FIGURE DESCRIPTION Q'TY
Table Top
Leg
PARTS LIST
4 Pcs
1 Pc
1 Pc
Hardware Bag
DV14260-13
Pedestal 1 Pc DV14260-08
DV14260-13
DV14260-08
DV14260-07
Apron Hinge 4 Pcs DV14260-02
Leaf Hinge 3 Pcs DV14260-09
Glides 2 Pcs DV14260-05
Support Leaf 1 Pcs DV14260-17
Mounting Plate 1 Pc DV14260-18
Side Mounting Plate 2 Pcs DV14260-19
Hook Lock 4 Pcs DV14260-10
Support Leaf Hinge 2 Pcs DV14260-12
Apron Leaf 2 Pcs DV14260-20
DV14260-07
DV14260-20
DV14260-01
TBSR-10369BC-CNGN MADE IN MALAYSIA
PAGE 1 OF 3
T1-VG4260-O & -C

SOLID TOP BUTTERFLY LEAF PEDESTAL TABLE
TBSR-10369BC-CNGN MADE IN MALAYSIA
PAGE 2 OF 3
STEP 2
NOTE : THE UNIT SHOULD BE ASSEMBLED BY 2 OR MORE PEOPLE.
ASSEMBLY
STEP 1
Hex Nut
Hex Nut(5/16")
12 pcs Lock Washer
Lock Washer(5/16")
5/16"5/16"
12 pcs Flat Washer
Flat Washer(5/16")
Pedestal
Leg Level Glide
5/16"
12 pcs Lock Washer
M6x13mm
10 pcs Flat Washer
M6.5x16.5mm
10 pcs
Wrench
Wrench
1 pce Allen Key 1 pce
M6x50mm
JCBC Bolt
10 pcs
HARDWARE PART :
Turn the pedestal upside down. Attach legs by inserting
hanger bolts through pre-drilled holes on pedestal.
Put a Flat Washers(5/16"), Lock Washers(5/16") and
Hex Nut(5/16") onto the hanger bolts then tighten with
the provided Wrench.
Position the table top upside down on a smooth, protective
surface such as carpet. Remove and discard the temporary
Wood Strip. Install the side panel and secure with
Flat Washers(M6.5x16.5mm), Lock Washers(M6x13mm) and
JCBC Bolt. Attach Mounting Plate as shown. Secure with
Flat Washers(M6.5x16.5mm), Lock Washers(M6x13mm) and
JCBC Bolt(M6x50mm), then tighten all JCBC bolts with Allen Key
provided.
STEP 3
Unlock the hooks underneath the table and pull the table top wide
open equally from both ends. Align and attach the table top to the
pedestal. Insert a Flat Washers(5/16"), Lock Washers(5/16") and
Hex Nuts(5/16") onto the hanger bolts. Tighten all Hex Nuts with the
provided Wrench.
Lock Washer(M6x13mm)
Lock Washer
(M6x13mm)
Allen Key
Allen Key
JCBC Bolt(M6x50mm)
JCBC Bolt
(M6x50mm)
Flat Washer(M6.5x16.5mm)
Flat Washer
(M6.5x16.5mm)
Mounting Plate
Side Panel
Lock Washer(5/16")
Flat Washer(5/16")
Wrench
Hex Nut(5/16")
Unlock Hook
Remove wood strip
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children. Two or more people are needed for
assembly.
IMPORTANT NOTE :
1. Use only the hardware supplied.
2. Do not over-tighten bolts.
3. This item may require periodic tightening.
T1-VG4260-O & -C

SOLID TOP BUTTERFLY LEAF PEDESTAL TABLE
TBSR-10369BC-CNGN MADE IN MALAYSIA
PAGE 3 OF 3
STEP 4
Lift both leaves from the compartment and flip up the aprons then unfold table leaf and place the leaf on the top surface carefully.
Flip down apron
Lock Hook
Unlock Hook
STEP 5
Push table top from both ends to close gap and lock the hooks underneath the table. Adjust the level glides until the table sits firmly.
TO STORE THE CENTRE LEAF WHEN NOT IN USE
Unlock the hooks underneath the table and pull the table top wide open equally from both ends. Flip down the aprons and fold the
centre leaf to store within the compartment. Push table top from both ends to close. Lock the hooks underneath the table.
Lock Hook
Level Glide
Flip up apron
IMPORTANT NOTE:
Storing and opening the leaf
requires 2 people.
~
T1-VG4260-O & -C