Winterhalter Gastronom RoMatik 150 User manual

89005234-02
05/06 sch
Winterhalter Gastronom GmbH
Tettnanger Str. 72
D-88070 Meckenbeuren 1
Installation Instructions
Winterhalter Gastronom RoMatik 150
In order to guarantee many years of trouble-free
service, we recommend that you sign a mainte-
nance contract with your local Winterhalter ser-
vice centre.
Contents:
1. Safety information.................................................................................................................... Page 1
2. Unpacking................................................................................................................................. Page 2
3. Installation................................................................................................................................ Page 2
4. Connection............................................................................................................................... Page 3
1. Safety information
• The appliance must be connected to the water supply and drainage system by a trained fitter in
accordance with the locally applicable regulations.
• The data in the connection diagram must be observed.
• Only corrosion-resistant materials such as stainless steel, plastic or food-safe, compression-proof rub-
ber may be used at the purified-water end.
• The RoMatik 150 must be installed in the upright position.
• The RoMatik 150 may only be connected to one consumer (dishwasher).
• The appliance may only be connected to the cold water supply (max. 30°C).

2
Winterhalter Gastronom GmbH
Tettnanger Str. 72
D-88070 Meckenbeuren
89005234-02
05/06 sch
2. Unpacking
• Pull off tear strip at the centre of the cardboard box.
• Remove upper half of cardboard box.
• Lift appliance out of box in its polystyrene shell.
• Check to make sure appliance is undamaged.
• Take appliance to installation site.
3. Installation
When installing the appliance, observe the enclosed
connection diagrams as well as the following instruc-
tions:
• Assemble the appliance in an upright position in
the vicinity of the dishwasher.
• Make sure the cold water, reject water and
power connections are close to the appliance.
• Make sure the monitoring indicators of the appli-
ance remain visible.
• Make sure the front door can be opened in order to
change the filters.
• Ensure adequate ventilation: leave a 2 cm gap
between the sides of the appliance and any adja-
cent fitments or walls to allow air circulation.
• Take care to avoid crushing any connections
during assembly.
• The appliance is not splash-proof. Do not clean
the outside with a wet cloth or with a high-pressure
or steam-jet cleaning device. Do not use detergents. Only wipe the outside of the appliance with a
damp cloth.
If the appliance cannot be protected against splash water for structural reasons, an additional substruc-
ture should be provided.

89005234-02
05/06 sch
Winterhalter Gastronom GmbH
Tettnanger Str. 72
D-88070 Meckenbeuren 3
4. Connection
First check whether the dishwasher to which the RoMatik 150 is to be connected has a pressurised boiler
(subject to water-pipe pressure) or a non-pressurised boiler (pump installed downstream of boiler).
Refer to connection diagram 890053104 for machines with pressurised boilers and connection diagram
890052364 for other machines.
For further information, contact your local Winterhalter service centre.
Removing the shipping seals:
The feed water (cold water), reject water and purified water connections are located at the rear of the
appliance, and are sealed with plugs.
Do not use pliers to remove the plug from the purified water outlet!
The plug can be easily removed by pushing the grey retaining ring towards the rear of the appliance and
then pulling it out (see also the instructions at the bottom of this page).
Remove the other seals.
The seal for the cold water connection will be needed again.
Cold water connection:
Connect the on-site shut-off valve (cold water) to the RoMatik 150 with the supplied parts according to
the connection diagram. For this purpose, choose a water valve which can never be shut off inadvertently.
The dirt trap of the dishwasher must be used.
If connecting to a new drinking water pipe, or to one which has not been used for some time, allow the water
to run for a while before connecting the hose. This serves to prevent sand or rust from collecting in the intake
filter of the appliance.
Note: Once the appliance is fully assembled, both the on-site shut-off valve and the water dial must be
easily accessible for maintenance work.
Check the hose connections for leaks. Make sure the mains plug is removed before doing so, as oth-
erwise a flushing cycle will be instantly activated.
Purified water connection:
Now connect the RoMatik 150 to the dishwasher with the supplied parts according to the connection dia-
gram.
The supplied service tap must not be mounted until the appliance is put into operation by your
authorised Winterhalter service technician.
The hose between the RoMatik 150 and dishwasher / expansion tank must not be shortened.
Information on plastic hose and quick connectors:
Connecting the hose:
Insert the hose approx. 20mm into the quick
connectors at the rear of the appliance or ser-
vice tap.
Disconnecting the hose:
The hose can be disconnected from the quick
connectors by pulling back the grey ring.

4
Winterhalter Gastronom GmbH
Tettnanger Str. 72
D-88070 Meckenbeuren
89005234-02
05/06 sch
Reject water connections:
Mount the drain hose on the RoMatik 150 with hose clips and route it to a drain funnel.
Note: Once the appliance is fully assembled, the reject water connection must be easily accessible for main-
tenance work.
Once all the connections have been completed, the RoMatik 150 is ready for operation.
The start-up procedure must be performed by a service technician trained at the Winterhalter works in
accordance with the "Start-up instructions for Winterhalter Gastronom RoMatik 150".
At the same time, the customer is briefed on the operation of the appliance.
Electrical connection:
Do not insert the mains plug: this must be done by your authorised Winterhalter service technician.
The electrical connection must be permanently guaranteed (including at night). There must be a constant
power supply to the appliance in order to avoid internal damage to the membrane.