Wirata SF-160A User manual

MODEL NO.
SF-160A
POWER
50W
VOLTAGE
220-240V
FAN SIZE
18” (400mm)
FREQUENCY
50-60Hz
FAN SPEED
3
NO. OF BLADE
5
INSTRUCTION MANUAL
Model No.:
SF-160A
Please read Instruction Manual before use
& follow ALL the instructions carefully.

WHAT’S IN THE BOX
PARTS DESCRIPTION
1. Wall Fan –1set
2. Instruction Manual–1 set
MAIN COMPONENT：
(Product may vary slightly from
what is illustrated)
1: Front Guard
2: Guard ring
3: Blade cap
4: Blade
5: Blade lock
6: Rear Guard
7: Motor
8: Leg
9: Control panel
10: Base
11: Washer
12: L type screw
13: Oscillation knob
14: Power line
15: Screw fixer for fan body
16: Adjustable pole

When using the electrical appliance, the following basic
safety precautions should always be followed.
Please read these instructions carefully. Pay your special
attention to important safety instructions. Keep this
“Instructions for use” for future reference.
WARNING - To reduce the risk of fire, electric shock or injury to persons
or property:
1. Before use, check if the voltage supply with the
specifications marked on the voltage label attached to
the appliance bottom.
2. Before use, you should check if the power cord and
plug is not damaged. To avoid poor contact, please do
not bend or twist the power cord with force.
3. Before unplugging the power plug, turn off the power.
Do not use wet hands to pull the plug to avoid electric
shock.
4. Please do not hang any clothes on the fan guards.
5. Do not use it before assembling.
6. Please do not use it at the place where there is curtain.
Otherwise, the motor will stall and operate abnormally.
7. Please do not use the fan at high temperature (above
30°C) and high humidity area (shower rooms), and
dusty areas. Otherwise, deformation or failure will be
resulted.
8. Please do not insert the figure or any object into the
guards when the fan is running. It will cause injury to
person especially children.
9. Please do not spray insecticide on the fan. Otherwise,
the resin and painted parts will be affected.
GENERAL INSTRUCTION
SAFETY INSTRUCTIONS

10. Please do not blow the baby, elder and patient directly
for long time.
11. Do not use it in an uneven or unstable place where
drop or damage might be caused.
1. Assembly of leg:
a) Insert the front part of leg into the hole to the
base.
b) Push down the leg in place so as to make the two
matches perfectly.
c) Screw or fasten leg and base.
2. Rear guard assembly:
a) Clockwise draw out the blade cap, and take out the
guard lock anticlockwise, and then install the rear
guard aligning it with the three struts on the front
motor cover.
b) Lock and fix it clockwise with the guard lock.
3. Fan blade assembly:
a) Insert the fan blade into the motor shaft to the
uttermost with the back of the leaf completely
aligning with the motor pin.
b) Anticlockwise clock the blade cap into the motor
shaft and fix it tightly.
4. Front guard assembly:
a) Hang the hanger at the front guard on the right top
of the rear guard, and fasten the guard ring tightly
around the rear guard.
WARNING: Do not use the device near water, over the bath tub,
pool or other water basin.
*Observe the above-mentioned rules in order to avoid burning,
electric shock or fire hazard. Make sure you understand the
instructions.
ASSEMBLY INSTRUCTION

b) Be sure to make the front and rear guards
completed aligned.
c) Press into the fixing guard clip under the front
guard ring and lock the guard clip screw.
1. Press the buttons speed to control fan:
0-stop,1-low,2-medium,3-high.
2. Oscillation: To control the oscillation, switch up the
oscillation knob oscillation OFF, switch down the
oscillation knob oscillation ON.
3. Loosen the nut of adjustable pole to adjust the height,
then tighten the nut when got the height needed.
4. Routing the timer to select the time, do not routing
back the timer (only if it has a timer).
1. Clean and maintain the fan according to the illustration
on the right.
2. Be sure to clean the fan body and fan blade to avoid
color change or damage.
3. After maintenance, please follow the original packing
orders to keep the fan properly stored.
4. Properly store the fan at a dry place.
5. The fan only needs some general external
maintenance.
6. Before cleaning, please turn off all power supply.
7. Firstly, clean with kitchen detergent. Then, wipe it
clean with soft cloth.
8. Never wash with water.
9. To avoid discoloring or deterioration, do not wipe with
thinner, toluene, acid detergent, kerosene, alcohol or
chemical cloth.
HOW TO OPERATE
CLEANING INSTRUCTION

1. Surrounding air maximum temperature: +40°C
2. The surrounding air is highest the relative
temperature: 90% (+25°C)
3. Elevation: <1000m
ENVIRONMENT PROTECTION
Dispose the appliance according to the local garbage
regulations. Never throw it away to the rubbish, so you will
help to the improvement of the environment.
USE ENVIRONMENT