Wireless Pacific X10DR ELITE Operating instructions

Secure Wireless Microphone
Programming Feature
Comparison
WIRELESS PACIFIC
...WHEN IT MATTERS
TM
ELITE PRO CLASSIC

How to use Programmer:
Start Programming application
Runs On PC or Mac running Windows 7/8.
To put Handset into programming mode, attach
programming cable between device hirose port and
PC then start handset while holding PTT. LED will light
pink.
To put Gateway into programming mode, attach
programming cable to device Mini-USB port and PC
USB port before holding the Gateway ON/OFF button.
LED will light pink. (The gateway’s RJ45 socket should
not be connected.)
Always READ device first.
Read Device
Press to load current programming parameters from
device to screen.
Program Device
Press to load current screen programming
parameters to device.
Load File
Press to load a previously saved programming parameters
to device from its saved PC location.
Save File
Press to load a programming parameters from screen to desired PC
location saved location.
Defaults
Press to load screen with default device parameters.
Exit
Press to exit program.
Restart (important)
Press to restart programmed device before removing programming cable
WIRELESS PACIFIC
...WHEN IT MATTERS
TM

Handset Parameters
WIRELESS PACIFIC
...WHEN IT MATTERS
TM
ELITE PRO CLASSIC

Programming Feature:
Basic functions - Handset
Radio PTT key beep
Sounds talk permit tone sequence whenever PTT is pressed and handset
is in range of its gateway. Default - OFF
Emergency key beep
Sounds single tone whenever Emergency button is pressed and handset
is in range of its gateway. Default - ON
Talkaround PTT key beep
Sounds talkaround tone sequence whenever Talkaround button is
pressed and handset is in range of its gateway. Default - ON
Stealth mode always active
Disables all alert tones and LED status light. User can manually enable
stealth mode if programmed off. Default - ON
Mute speaker on PTT
Disables all speaker audio whenever PTT is pressed. Default - OFF
Mute speaker on charge
Disables all speaker audio whenever handset is placed in gateway of
charger. Default - OFF
LED charge indicate
Disables “momentary blink” charge indicate on handset when device is
charging whenever handset is placed in gateway or a charger.
Default - ON
Auto turn on when charging
Causes handset to automatically turn on whenever it is placed in gateway
or a charger. Default - ON
Out of range turn off time
Sets time in hours that a handset that is not actively connected to a
gateway will remain powered on before turning itself off. Default - 8 hours
Low battery beep voltage
Sets the remaining battery voltage that will cause the low battery alert tones to be
generated. (for longer shift life you may set voltage lower but you may get less warning
before device automatically shuts off. Default 3.5V
Low battery beep interval timer
Sets the interval that the low battery alert tones are sounded in the handset.
Default 5 minutes
WIRELESS PACIFIC
...WHEN IT MATTERS
TM

Programming Feature:
Audio Levels - Handset
WIRELESS PACIFIC
...WHEN IT MATTERS
TM
Internal Mic Gain
Sets the internal microphone’s transmit audio level. Default 0
Internal Mic High Gain Boost
Sets the internal microphone’s sensitivity when “Live Mic” is active
External Mic Gain
Sets the external microphone’s transmit audio level. Default 0
External Mic High Gain Boost
Sets the external microphone’s sensitivity when the X10DR’s “Live
Mic” is active or when user manually selects high gain by powering up
microphone with blue volume up button pressed. Default 6
Remote PTT Gain Boost
Remote PTT gain Boost
Increases sensitivity of internal microphone when remote/handlebar PTT
is pressed. Default 9
Fixed Alert Tone Volume
Limits all user monitored alert tones to level set below rather than being
controlled by handset volume controls . Default OFF
Alert Tone Volume
Sets the value of the “Fixed Alert Tone” a user will hear from their
handset. Default 5

Programming Feature:
Emergency - Handset
WIRELESS PACIFIC
...WHEN IT MATTERS
TM
Audio link active time
- Applicable when handset is configured for press & hold emergency
Sets the time the internal ( or external if accessory is detected) that
transmit audio is active after Emergency button is released. Feature is
intended for those mobiles that activate their own internal “Live Mic”
function whenever emergency is triggered. This allows the microphone’s
Tx audio to be broadcast over the radio’s transmit channel, (assuming
mobile can source “Live Mic” from its external mic input). Default - 0
Advanced Emergency - Elite Models only
- Applicable when Elite handset is configured for short/long press
emergency
Transmit Time
Sets the time duration that X10DR “Live Mic” handset Tx audio is active
when Advanced Emergency activated. Default - 0
Receive Time
Sets the time duration that X10DR “Live Mic” handset Rx audio is active
when Advanced Emergency activated. Default - 0
Emergency repeat cycles
Sets the number of “Live Mic”, Tx and Rx cycles when Advanced
Emergency is triggered. Default - 1
Transmit audible emergency tone
Causes an audible emergency warble tone to be transmitted over the host mobile
radio channel. Default Off

WIRELESS PACIFIC
...WHEN IT MATTERS
TM
Programming Feature:
Hardware - Handset
Acc PTT
Sets whether Hirose PTT input generates Talkaround or radio PTT. Default - Radio PTT
PTT
Sets function of main large PTT button. Choices Radio PTT, Talkaround PTT or disabled.
Default - Radio PTT
Top 1
Sets function of top left button. Choices Emergency, Radio PTT, Talkaround PTT or disabled.
Default - Emergency
Top 2
Sets function of top right button. Choices Emergency, Radio PTT, Talkaround PTT or
disabled. Default - Talkaround PTT
Left 1
Sets function of top left button.
Press & Hold choices Emergency, Radio PTT, Talkaround PTT or disabled.
Short or Long Press choices Vol Up, Vol down, Aux 1, Aux 2, Emergency or disabled.
Short or Long Press - Default - short press Volume up
Left 2
Sets function of bottom left button.
Press & Hold choices Emergency, Radio PTT, Talkaround PTT, ON/OFF or disabled.
Short or Long Press choices Vol Up, Vol down, Aux 1, Aux 2, Emergency or disabled.
Short or Long Press Default- short press Volume down
Right 1
Sets the function of right side button. Long Press Default - OFF/ON
Hirose Pin 2 function - Elite models only
Sets Hirose pin 2 to be either BAT+ (~3.8VDC) to power external accessories or bridged
output speaker audio when pin 2 is set for speaker negative. Default - Speaker VE-
Long Press Duration
Sets time button must be pressed to detect a Long Press. Default - 1000mSec

WIRELESS PACIFIC
...WHEN IT MATTERS
TM
Gateway Parameters
ELITE PRO CLASSIC

WIRELESS PACIFIC
...WHEN IT MATTERS
TM
Programming Feature:
Audio Levels - Gateway
Receiver Input Gain From Radio
Sets the receive input sensitivity. Default - 6
Transmit Output Gain To Radio
Sets the audio output level to radio when “Live Mic” is active or when
local/remote /handlebar PTT is pressed. Default - 0
Talk Around Output Gain to other X10DRs
Sets the “intercom” microphone audio level. Default - 6
Monitor Emergency Input Alert Tone - Elite Models Only
Causes Emergency warble alert tone to sound in other cross connected
X10DR handsets when emergency input is triggered. (Maybe from another
X10DR or externally supplied input). Default - OFF
Find Me™ Function
Enables Find Me function in gateway. User double presses gateway On/Off
button to trigger Find Me alert tones. Default - OFF
Dual Operational Mics - Elite Models Only
Allows two Elite Mics to be simultaneously operational through the one Elite
gateway unit. Default - OFF
Public Address Mode - Elite Models Only
Sets the gateway so only handset Talkaround audio is amplified to the 8 watt
audio amplifier. When unchecked both Radio PTT and Talkaround audio is
amplified for in-car monitor use. Default - OFF
Radio Receive VOX/COR
Enables VOX derived COR. Default - ON
VOX Trigger Level
Sets the gateway’s audio detect sensitivity for VOX derived COR. Default - 50

WIRELESS PACIFIC
...WHEN IT MATTERS
TM
Programming Feature:
Hardware - Gateway
I/O
Defines whether the specific gateway interface pin is assigned as an input or an output.
Active
Sets whether the interface pin needs to be held low or pulled up high to activate assigned
functionality.
Choices for Output are:
Emergency, Radio PTT, Talkaround PTT and disabled.
Elite gateways also allow Aux 1, Aux 2, Handset in Cradle indicate, Handset out of range
indicate to be selected.
Choices for inputs:
Radio COR, Remote PTT, Find Me™ external trigger and disabled
Functions
Assigns desired functionality to Interface pin
Pulse
Defines the length of time an input must be activated before the function is triggered or
alternatively how long an output is activated when the assigned function has been triggered. A
value of zero means an input triggers instantly.