Wisi WA 8000C User manual

User’s Manual WA 8000C

CONTENTS
Safety use..........................................................
Danger warning................................................
Note................................................
Chapter 1 Overview................................
1.1 Features................................................................
1.2 Accessories...........................................................
Chapter 2 Introduction of panel function.....
2.1 Remote Control........................................................
2.2 Front panel introduction..........................................
2.3 Top panel introduction.....................................
2.4 Rear panel introduction.....................................
Chapter 3 Detail operation guide............
3.1 DVBS.............................................
3.1.1 Satellite Finding.............................
3.1.2 Dish Setup........
3.1.3 Angle Calculation...............
3.1.4 Constellation Analyzer..........
3.2 DVBT.........................................
3.3 DVBC..............................................
3.4 Compass..............................................
3.5 Spectrum..............................................
3.6 Multimedia............................................
3.7 Setting.........................................................
3.7.1 Program.............................
3.7.2 EPG........
3.7.3 Device Setup.............................
3.7.4 System.............................
3.7.5 Picture.............................
3.7.6 Option.............................
3.7.7 Time.............................
3.7.8 USB Upgrade.............................
Chapter 4 Technical Specifications.............

Safety use:
①. Consumers who using the product for the first time should read this manual carefully.
②. Don not touch the LCD screen.
③. Don not place heavy items on the device.
④. Don not lay the device closes to heating source, in the sunshine, in place with strong mechanical
vibration or full of dust.
⑤. Please place the device in ventilated surroundings.
⑥. The device should be fully charged before using for the first time (recommend 6 hours for the first
charging).
⑦. Contact the provider when malfunction of the device happen.
⑧. Damaging the device on operation without following the guideline would not be warranted.
⑨. Do not use the other cables like headphone,only using the AV cable in the package.
Danger warning:
(1). Prohibition of decomposition of batteries.
(2). Prohibition of battery short circuit.
(3). To reverse the positive and negative pole terminal.
(4). No heating and burning batteries.
(5). Avoid using batteries near heat sources.
(6). Do not get wet.
(7). To avoid charging in the vicinity of fire or direct sunlight.
(8). Use a dedicated charger and proper charge.
(9). Prohibit the destruction of batteries.
(10). No direct welding on battery.
(11). Do not connect the battery charging in the power outlet or car cigarette lighter.
(12). Do not use batteries for other devices.
(13). Do not direct contact with the battery.
(14). When the battery and the electric equipment are connected or charge, we must pay attention to the
polarity of the battery.
(15). Please take personal protection when using the voltage measurement function. The measured voltage
must not exceed 110V
(16). Use the antenna for power supply. Please ensure the power supply requirements of the external device.
The maximum current is 350mA. The maximum power is 8.5W.
Note：
(1). In the strong sunlight, use the battery, please do not use the battery in the strong sunlight exposure, so as
not to heat, deformation, smoke. At least to avoid battery performance degradation, reducing life.
(2). Anti static:The battery is equipped with protective circuit to avoid the occurrence of various accidents. Do
not use the battery in the generation of static electricity, because the static electricity (100V above) is
easy to damage the protection board, and lead to battery work is not normal, heat, deformation, smoke or
fire.

(3). Charge temperature range:Recommended charge temperature range is 0~45. Charging in the environment
beyond this range may cause a decrease in battery performance and reduce the life span.
(4). Charging mode:Please use the special charger and the use of the recommended charging mode, in the
recommended environment to the battery charge. After the discharge of the battery, please charge the
battery in time.
★Due to the special characteristics of the car, the battery can not reach the saturation state when the
vehicle is used to charge the battery.
(5). First use:In the first use of the battery, if the battery is not clean or abnormal smell and other abnormal
phenomenon, can not continue to use the battery for its equipment, should be returned to the seller.
(6). When is not a long time, to remove the battery from the device and put them in the low temperature and
humidity environment preservation. Battery has a life, if the use of the battery when the work of the
device is less than usual, to replace the battery.
(7).Children's use:Children use the battery, should be subject to parental guidance, and in the use of the right
to be monitored.
(8). To avoid contact with children:The battery should be placed in a position where the child can't get.
Children should be avoided to take the battery from the charger or use the device to play.
(9). Pay attention to leakage:If the battery leakage to the skin or clothing, please rinse immediately with water,
so as to avoid skin discomfort, etc.
(10). Consultation:When buying batteries, please pay attention to the vendor contact method. In order to get
in contact with the seller when needed and get advice.
(11). Period of guarantee:The warranty period is 6 months from the date of shipment. However, if the problem
is not due to the failure of the company's manufacturing process, but due to improper use, even in the
warranty period, manufacturers will not be free to replace the new battery.
(12). Safe use:In order to ensure the safety, please consider whether the electric type, system and lithium ion
battery protection circuit is matched in advance. In addition, it is also to consider the high rate current,
fast charge and the feasibility of specific applications.
◆Any loss caused by the improper use of the above shall not be responsible for
the company!

Chapter 1 Overview
The is a HD digital signal meter and portable device for installation and adjustment of satellite and
terrestrial receiving antenna.
1.1 Features:
■Combo of DVB-S2 and DVB-T2 DVB-C
■High resolution 5’’TFT LCD
■Multi-lingual OSD and use-friendly UI
■Support Spectrum function
■Real time constellation display
■Support TP search and blindly search
■USB 2.0 for software update/media play back
■Support time shift
■Support TP PVR
■Support program edit (move/skip/lock/delete/rename)
■Support electronic program guide (EPG)
■Support HDTV video/audio output
■Support AV input for monitor installing
■Support DC+12V out for monitor installing
■Very easy to use with shortcut key
■Support RCU
■Build in loudspeaker for audio play
■Visual and audible signal when signal received
■Build in highlight LED light
■Large lithium battery capacity(4000mAh)
■Support HD TV input
■Support 8MP camera input, supported formats are AHD TVI CVI CVBS
1.2 Accessories:
■Manual x1
■Power Adapter x1
■Power Line x1
■Car Adaptor x1
■Connector F to F type x1
■Connector F to IEC type x1
■Connector BNC to AV x1
■AV Cable x2
■Remote Control Unit (RCU) x1
■Device Bag x1

Chapter 2 Introduction of panel function
2.1 Remote Control
1.Power
2.Show the teletext content if
teletext is transmitted
3.Subtitle Language
4.Sleep
5.Find
6.Play Stop and Pause
7.Main Menu
8.Confirm the highlighted menu item. Open the channel list
9.Left and Right
10.EPG
11.Fast Backward and Fast Forward
12.Numeric Key(0-9)
13.Favorite channel
14.Mute
15.Multi-colored buttons
16.Zoom
17. PVR
18.GOTO TP or Satellite
19.Recall
20.Start Recording
21.Exit
22.Up and Down
23.Display information
24.TV/Radio
25.Play previous item and Play next item
26.Satellite list
27.Audio Language

2.2 Front panel introduction
1. Power switch: press it for 3~4 seconds to switch the device power on/off
2.Power indicator
3.Battery indicator(Red light for charging, green light for fully charged)
4.13V indicator
5.18V indicator
6.22KHz indicator
7.Signal Locked indicator
8.F1~F4: shortcut keys
9.Numeric keys
10. GOTO: Select satellite or transponder
11. LIGHT: use for input data,Long press 3~4seconds to turn on LED floodlight
12.SCREEN: Signal source switching
13.MUTE: turn on or turn off the voice
14.SPEC: shortcut key for spectrum analyzer
15.CONS: shortcut key for constellation analyzer
16.FIND: shortcut key for satellite finding
17.ANGLE: Shortcut key for Angle calculation
18.Arrow keys:The keys offer the movement of cursor to a specified direction.
19. OK: confirm key
20.MENU: Show main menu
21.EXIT: exit menu (main menu or sub menu)
22.Digitron : Show the current signal quality

23.LCD screen
24.Remote Control Input
2.3 Top panel introduction
1. F connector male for LNB IN
2. F connector male for ANT IN
3.USB connector
4.HDTV OUT connector
5.AV OUT connector(3.5 PHONE JACK)
6.AV IN connector(3.5 PHONE JACK)
7.Reset key
8.DC jack(for charger)
9. HD IN connector
2.4 Rear panel introduction
1.LED floodlight
2.Holder
3.Loudspeaker
4.Battery
5.Handle sleeve

Chapter 3 Detail operation guide
When you turn on the device, you can see the main menu
which consists of DVB-S2, DVB-T2, DVB-C, Compass,
Spectrum, Multimedia and Setting.
3.1 DVB-S2
3.1.1 Satellite Finding
Move cursor to“Satellite Finding ’’and press“OK’’, then
you can enter the“Satellite Finding’’ interface.
■Press“OK’’ on the Satellite option, then you can see the
following window. Press[▲/▼] to select the existed
satellite and you can press“OK’’ to confirm.

■Press“OK’’ on the LNB Type option, then you can see
the following window. Press[▲/▼]to select the LNB
Type and you can press“OK’’ to confirm.
■Press“OK’’ on the Freq、Symbol Rate、Polarity option,
then you can see the following window.
■Use the digital button to input the Frequency, Symbol
Rate and Polarity manually, then you can press“OK’’ to
confirm.
■When the signal is locked, the buzzer will sound with the
fastest repetition. The signal quality bar will also be
displayed on the LCD. Meanwhile, the LOCK LED will light
up.
■Press“OK ’’on the Search option, and the satellite finder
will begin to search the channel according to the TP you
select or input manually. It will switch to the Program page

after the search (if there is a program on the Transponder).
3.1.2 Dish Setting
Move cursor to“Dish Setup’’ and press“OK’’, then
you can enter the“Dish Setup’’ interface.
■Under the Satellite list page, you can press[▲/▼]to
select the satellite.
■Press [F1] to add a new satellite through setting Satellite
Name, Longitude Direction, Longitude Angle or Band.
■Press [F2] to edit existed satellite, which is including
Satellite Name, Longitude Direction, Longitude Angle
and Band.

■Press [F3] to delete existed satellite. If you press OK , the
satellite will be deleted or you can press“EXIT’’ to exit.
■Press[F4]to Begin Scan, with Default, Blind Scan,
Network these three scan modes.
■Press [GOTO] to get into the TP list, you can also use
[F1] [F2] [F3] [F4] to add, edit, delete or begin to scan the
selected TP, and Press [GOTO] to return to the satellite
list.

■Selete one of the satellites and press[◀/ ▶]to get into
the LNB Type setting.
■LNB Type: Press[▲/▼]to choose LNB Type between
9750/10600, 9750/10750, 05150, 05750, 09750, 10600,
10750, 11300 and 11475.
■LNB Power: Press[◀/ ▶]to choose between
Off/13V/ (13V/18V)/18V.
■22K: Choose AUTO/ON/OFF.
■Toneburst: Press[◀/ ▶]to choose between
None/BurstA/BurstB.
■DiSEqC1.0: Press[◀/ ▶]to choose between
None/LNB1/ LNB2/ LNB3/ LNB4.
■DiSEqC1.1: Press[◀/ ▶]to choose between
None/LNB1~LNB16.
■Motor: Press[◀/ ▶]to choose between
None/DiSEqC1.2/DiSEqC1.3.
3.1.3 Angle Calculation
Move cursor to“Angle Calculation ’’and press“OK’’ , then you can
enter the“Angle Calculation’’ interface.
■Press[◀/ ▶]on Satellite option to select the existed
satellite, the longitude of the satellite will be changed
correspondingly.

■Press[▲/▼]on Sat Longitude option, then you can use the
digital button to input the satellite longitude you want.
■If you select Manual, then you can move cursor to the
Local Longitude and the Local Latitude and use the
digital button to input the number you want.
( Press[◀/ ▶]to select east or west local longitude, south
or north Hemisphere).
■When a parameter has changed, the system will
calculate the result and will show the picture on the
screen automatically.
3.1.4 Constellation Analyzer
Move cursor to“Constellation Analyzer ’’ and press“OK’’ , then
you can enter the“Constellation Analyzer ’’ interface.
■Press [◀/ ▶]to select satellite and you can see the
Transponder changes correspondingly.
■Press [◀/ ▶]to select Transponder and you can see TP
frequency, Symbol Rate and Polarity change
correspondingly.
■Press“OK ’’, then you can see the quality bar and the
strength bar.
■Under Constellation Analyzer interface (by Frequency),
press [▲/▼]to switch between other Frequency of selected
satellite

3.2 DVB-T2
Move cursor to“DVB-T2’’and press“OK’’, then you
can enter the“DVB-T2’’interface.
■Press[▲/▼]on Manual Search and press“OK’’ , then you
can see the following menu.
3.3 DVB-C
Move cursor to“DVB-C’’and press“OK’’, then you
can enter the“DVB-C’’interface.
■Press[▲/▼]on Manual Search and press“OK’’ , then you
can see the following menu.

3.4 Spectrum
Move cursor to“Spectrum’’ and press“OK’’ , then
you can enter the“Parameter Setting’’ interface.
■Press [F1] to switch SPAN of spectrum frequency, FULL as default,
The smaller span will show clearer signal status of frequencies.
■Press [F4] to pause current status.
■Press [▲/▼] to move vertical coordinate's position.
■Press[◀/▶]to move cursor to select frequency, the signal strength
of the selected frequency will be displayed on the left-top corner.
■DVB-S/DVB-T/DVB-C all support spectrum sub-board function
3.5 Multimedia
Plug USB and move cursor to“Multimedia’’ and press“OK’’ , then you can
enter the“USB’’ interface.

■Press[▲/▼]on Multimedia and press“OK’’ , then you
can see the following menu.
■Press[◀/ ▶] to select the item you want to get into and
press“OK ’’to select the file you want to play Music, Photo, Movie and PVR.
■Press[◀/ ▶]to select PVR and press“OK’’ , press[▲/▼] to select the [HBPVR] file and press“OK’’ , then
you can see the program you have recorded.
■The next time if you want to restore the factory default
and keep the satellites' information, you can press Backup to USB.
After all, you can see the satellites you have added.
3.6 Setting
Move cursor to“Setting ’’and press“OK’’ , then you
can enter the“System Setting’’ interface.

3.6.1 Program
Move cursor to“Program” and press“OK”, then you
can enter the“program”interface.
■Press [▲/▼] on Program Edit option and press“OK ’’, enter password: 000000
then you can see all the TV list.
■Move
1.Press [▲/▼] on channel list, select the channels which you want to edit in channel list by press [Red/F1]
Key.
2.Press [▲/▼] move the cursor to the position you want and press the [OK] key.
3.Press [EXIT] Key to save the settings.

■Lock (Password: 000000)
1.Press [▲/▼] on channel list, select the channel which you want to edit in channel list by press [Yellow/F3]
Key.
2.Press [Yellow/F3] Key to lock or unlock the channel.
3.Press [EXIT] Key to save the settings.
■Delete
1.Press [▲/▼] on channel list, select the channels which you want to edit in channel list by press [Blue/F4]
Key.
2.Press the [OK] key to sure delete the channel.
3.Press [EXIT] Key to save the settings.
■FAV
1.Press [▲/▼] on channel list, select the channels which you want to edit in channel list by press [FAV] Key.
2.Press [▲/▼] choose what you want “Favorite Type”and press the [OK] key.