Wohler eAMP1-8M User manual

eAMP1-8M
eAMP1-16M
1RU Dual Input 3G/HD/SD SDI Audio Monitor
User Guide
Part Number 821843, Revision A

eAMP1-8M/16M
Page 2
© 2023 Wohler Technologies, Inc. All rights reserved.
This publication is protected by federal copyright law. No part of this publication may be copied or
distributed, stored in a retrieval system, or translated into any human or computer language in any
form or by any means electronic, mechanical, manual, magnetic, or otherwise, or disclosed to third
parties without the express written permission of Wohler Technologies.
Reproduction
Licensed users and authorized distributors of Wohler Technologies, Inc. products may copy this
document for use with Wohler Technologies., Inc. products provided that the copyright notice above
is included in all reproductions.
Customer Support
Wohler Technologies, Inc.
1280 San Luis Obispo Ave
Hayward, CA, 94544
Phone: [phone]
Web: www.wohler.com
Sales: [e-mail]
Support: [email protected]
Disclaimers
Even though Wohler Technologies, Inc. has tested its equipment and software, and reviewed the
documentation, Wohler Technologies, Inc. makes no warranty or representation, either express or
implied, with respect to software, documentation, their quality, performance, merchantability, or
fitness for a particular purpose.
In no event will Wohler Technologies, Inc. be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect in the hardware, software, or its documentation,
even if advised of the possibility of such damages.
Some states do not allow the exclusion or limitation for incidental or consequential damages, so the
above exclusion or limitation may not apply to you.
PDF
All text strings appearing in this shade of blue are hyperlinks.
Other Technologies and Products
Google Chrome is a registered trademark of Alphabet Inc.
Microsoft Windows and Internet Explorer are registered trademarks of Microsoft Corporation.
Dolby is a registered trademark of Dolby Laboratories, Inc.
All product names, logos, and brands are property of their respective owners. All company, product
and service names used in this document are for identification purposes only. Use of these names,
logos, and brands does not imply endorsement.
Last Update
November 9, 2023

eAMP1-8M/16M
Page 3
TA LE OF CONTENTS
Table of Contents
User Guide ........................................................................................ 1
TABLE F C NTENTS .......................................................................... 3
Table of Contents ........................................................................................... 3
CHAPTER 1: Installation....................................................................... 6
Introduction .................................................................................................. 6
verview ............................................................................................ 6
Safety .......................................................................................................... 6
Instructions ......................................................................................... 6
Safety Symbols.................................................................................... 7
Mounting............................................................................................. 7
Heat Dissipation ................................................................................... 7
Sympathetic Vibration........................................................................... 8
Mechanical Bracing ............................................................................... 8
Electrical Interference ........................................................................... 8
Power ................................................................................................. 8
Compliance ................................................................................................... 8
FCC.................................................................................................... 8
ICES-003 ............................................................................................ 8
CHAPTER 2: Local peration................................................................. 9
peration...................................................................................................... 9
PTe Package Upgrade ................................................................................... 9
Dolby Package Upgrade ................................................................................ 10
Startup....................................................................................................... 10
Front Panel.................................................................................................. 10
Model Differences.......................................................................................... 11
Rear Panel................................................................................................... 12
Channel Meters and Touch perations............................................................. 13
Menu / ption Touchscreen ........................................................................... 15
Main Menu ........................................................................................ 16
Loudness Menu .................................................................................. 16
Loudness Meter.................................................................................. 16
Loudness Settings .............................................................................. 18
Source Select .................................................................................... 20
Presets ............................................................................................. 21
All Presets ......................................................................................... 21
Preset Favorites ................................................................................. 22
Unit Settings ..................................................................................... 23
Speaker ptions................................................................................. 24
Unit Configuration .............................................................................. 25
Phase Configuration............................................................................ 26
Analog Configuration .......................................................................... 27
Meter Scales...................................................................................... 28

eAMP1-8M/16M
Page 4
System ptions Menu ......................................................................... 30
Network Settings................................................................................ 30
System Reboot .................................................................................. 32
System Update .................................................................................. 33
Factory Reset .................................................................................... 34
System Information............................................................................ 35
Passcode Settings .............................................................................. 36
Forgotten Passcode ............................................................................ 38
CHAPTER 3: Technical Info ............................................................... 39
CHAPTER 4: The eAMP1-8M/16M Web GUI ........................................... 43
Web Browser / Control Device........................................................................ 43
First Time IP Assignments ............................................................................. 43
Peer-to-Peer Connection...................................................................... 43
Network Connection............................................................................ 44
Network Setup............................................................................................. 45
Dashboard .................................................................................................. 46
Audio Meters ............................................................................................... 50
System Preferences...................................................................................... 51
System Audio Clock Reference ............................................................. 51
Loudness Configuration Tab ................................................................. 52
Phase Indicator Configuration Tab......................................................... 53
Front Panel Configuration Tab .............................................................. 54
Preset Management...................................................................................... 57
Global utput Routing................................................................................... 61
Destination utputs............................................................................ 61
Source Inputs .................................................................................... 62
utput ptions .................................................................................. 62
Typical Questions Regarding Global utput Routing........................................... 63
What signal outputs can be controlled using the Global utput Routing
feature? ............................................................................................ 63
How do I route whatever is being monitored to the XLR?.......................... 63
How do I have a downmixed pre-fade output on the Analog XLRs combined
with a post-fade output on the Speaker/Headphone?............................... 63
How do I make the XLR outputs follow the Audio Meter screen solos & mutes
while the Speaker/Headphone does not?................................................ 64
How do I route only specific monitored channels to the Analog XLR outputs?
....................................................................................................... 64
How do I keep the internal speakers muted and have audio only on the
analog XLR outputs? ........................................................................... 64
How do I ensure that the outputs are automatically muted when the
Headphone jack is inserted?................................................................. 65
How do I ensure that my outputs are pre-faded but follow the solo-mutes on
the web interface? This will allow us to monitor only the unmuted/solo Audio
Meter channels on amplified stereo speakers connected to the Analog XLR’s.
....................................................................................................... 65
Preset Replication......................................................................................... 66
Import/Export Presets................................................................................... 68
Export Configuration........................................................................... 68
Import Configuration .......................................................................... 69
System Setup.............................................................................................. 70
System Information............................................................................ 70
Licenses............................................................................................ 71

eAMP1-8M/16M
Page 5
Factory Reset .............................................................................................. 72
Reboot System ............................................................................................ 73
APPENDIX A: Software Upgrades......................................................... 74
Introduction ................................................................................................ 74
Download the Software ................................................................................. 74
Update Methods........................................................................................... 74
Local Update from the Front Panel .................................................................. 75
Updating via the Web GUI using a Flash Drive .................................................. 77
Updating an eAMP1-8M/16M Remotely ............................................................ 79
Updating Multiple Units Remotely ................................................................... 81
APPENDIX E: API Documentation ........................................................ 84
Introduction ................................................................................................ 84
API: Presets ................................................................................................ 84

eAMP1-8M/16M
Page 6
CHAPTER 1: Installation
Introduction
verview
The eAMP1-8M and eAMP1-16M Audio Monitors are 1RU multichannel multi-source
audio monitors, each with two switched 3G-SDI inputs. These and the associated
other eAMP1-Series monitors allow the customer to select a model with the exact
channel and input source capabilities needed for an economical cost.
The eAMP1-8M/16M is compact and simple to operate, with straightforward
controls. It has a wide touch screen LCD display providing high resolution level
meters. Any audio channels (or channel pairs) from the selected 3G/HD/SD SDI
audio/video source stream may be monitored. Either 8 or 16 channel meters can be
displayed, depending upon the model.
With the purchase of the PTe Package option, monitoring setups are created and
configured using local menus and a web browser over a network connection to the
integral web server of the eAMP1-8M/16M. The web server will also allow you to
view the audio meters remotely. Purchase of the PTe Package, also enables
purchase of the PT-D LBY Package option for Dolby® D, DD+, and E bitstreams
monitoring. In other words, PTe Package purchase is required prior to purchase of
the PT-D LBY Package.
Safety
Instructions
1. Read, keep, and follow all of these instructions; heed all warnings.
2. Do not use this equipment near water.
3. Use only a dry cloth to clean the equipment.
4. Do not block any ventilation openings.
5. Do not install near any heat source such as a radiator, heat register, amplifier, or
stove.
6. Do not attempt to plug the unit into a two-blade outlet (with only two prongs of
equal width).
7. Protect the power cord from being walked on or pinched, particularly at plug
connection on the equipment and at the socket.
8. Use only the attachments/accessories specified by the manufacturer.
9. Unplug the equipment during lightning storms or when unused for long periods
Important:
By design, the supplied AC mains power cord will only plug into a
three-prong grounded outlet for your safety. If the plug does not fit
into the outlet, contact an electrician to replace the obsolete outlet.

eAMP1-8M/16M
Page 7
of time.
10. Refer all servicing to qualified service personnel. Servicing will be required
under all of the following conditions:
a. The equipment has been damaged in any way, such as when the power-
supply cord or plug is damaged.
b. Liquid had been spilled or objects have fallen onto the equipment.
c. The equipment has been exposed to rain or moisture.
d. The equipment does not operate normally.
e. The equipment has been dropped.
Safety Symbols
Mounting
The unit is designed for a standard 19" rack. Install it at ear/eye level for best high
frequency response and visual observation of the display screen. Please adhere to
the following clearances:
Table 1-1: Clearance Recommendations
Clearance Surface
24” Front
3” Rear
2” Sides
1.75” Top and Bottom (if either radiates heat)
0” Top and Bottom (if no heat)
Heat Dissipation
The ambient temperature inside the mounting enclosure should not exceed 40°
Celsius (104° Fahrenheit). Adjacent devices can be rack mounted (or stacked) in
proximity to the unit if this temperature is not exceeded. therwise, allow a 1RU
(1.75”/44.45mm) space above and below the unit for air circulation.
Important
:
Heat generated by the class D power amplifiers, power supplies,
and other components is vented by slots in the sides and back of
the unit. Therefore, as a safety precaution, you must allow proper
ventilation on these surfaces.
WARNING:
The symbol to the left warns of electric shock hazard inside the unit.
Disconnect the power cord before removing access panels when
installing upgrades. nly qualified service personnel are to operate
the equipment with covers removed, and are to exercise caution to
avoid personal injury.

eAMP1-8M/16M
Page 8
Sympathetic Vibration
Sympathetic vibration from other equipment (cables, etc.) in the rack may be
serious enough to interfere with the unit’s sound quality. If you experience
sympathetic vibrations, use thin card stock, felt, foam, or weather-stripping
between the vibrating surfaces. Tie loose cables securely with cable ties.
Mechanical Bracing
The 1RU chassis is securely attached to the front panel. In addition, the chassis has
mounting tabs through which you attach it to the rack rail. This feature will reduce
or eliminate rear bracing requirements in many mobile/portable applications. The
weight of internal components is distributed fairly evenly around the unit.
Electrical Interference
Be careful to avoid mismatched cable types and other similar causes of undesired
reflections in digital signal systems. If severe enough, such reflections can result in
corruption of the digital data stream. As with any audio equipment, maximum
immunity from electrical interference requires the use of shielded cable; however,
satisfactory results can sometimes be obtained without it. The internal circuitry
ground is connected to the chassis.
Power
The unit connects to an AC mains power source (100 to 240 VAC, 65W, 50/60Hz)
using an IEC power cord.
When the mains plug or appliance coupler is used as the disconnect device, the
disconnect device should remain operable.
Compliance
FCC
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
peration of this equipment in a residential area is likely to cause harmful
interference, in which case users will be required to correct the interference at their
own expense.
ICES-003
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.

eAMP1-8M/16M
Page 9
CHAPTER 2: Local Operation
Operation
The eAMP1-8M/16M can be operated easily and simply from controls on its front
panel, as described in this chapter. With the addition of the optional PTe Package,
it may also be accessed remotely in two ways, via the Wohler Web GUI for
administrative purposes or by third party equipment via Application Programming
Interface (API) commands. The Wohler Web GUI is described in Chapter 4 of this
manual. The API commands are described in Appendix E of this manual.
OPTe Package Upgrade
The optional licensed PTe Package Upgrade provides a number of powerful
features beyond basic audio monitoring. The additional features are as follows:
•Loudness Monitoring: Parameters relating to the setup of loudness
measurement can be set up and adjusted. The loudness of an input signal
can then be measured and displayed along with the input signal levels. Refer
to sections further in this chapter and to the System Preferences section of
Chapter 4.
•Preset Management and Preset Replication: Presets are setups that
allow you to set up which channels of the various inputs are displayed on the
meters and in which order. Presets can then be quickly selected as needed.
These presets can be copied to other eAMP1-8M/16M units to simplify
multiple system setups. Refer to the Preset Management and Preset
Replication sections in Chapter 4.
•Remote Meter Monitoring and Configuration: Related meter channels
may be grouped together and named for ease of monitoring. The meters may
be monitored via the Wohler Web GUI. Refer to the Dashboard section in
Chapter 4.
•Passcode Protection: The settings of the eAMP1-8M/16M may be protected
from tampering or accidental changes. This is done using a Passcode. Refer
to the Passcode Settings section of this chapter or the Front Panel
Configuration Tab section in Chapter 4.
•Application Programming Interface: The eAMP1-8M/16M may be
controlled by third party equipment via Application Programming Interface
(API) commands. These API commands are described in Appendix E.
An optional license key must be purchased to add the PTe Package. Refer to the
System Setup section in Chapter 4 to install licenses.

eAMP1-8M/16M
Page 10
Dolby Package Upgrade
The optional licensed Dolby Package Upgrade allows decoding and monitoring of
Dolby
®
D, DD+ & E. It includes Wohler Zoom & metadata. This option requires
prior purchase of the OPT-e Package Upgrade.
An optional license key must be purchased to add the Dolby Package. Refer to the
System Setup section in Chapter 4 to install licenses.
Startup
The eAMP1-8M/16M will begin its startup process when it is connected to power.
There is no power switch. It is normal for the product to require about 45 seconds
to start up and be ready to use.
When the eAMP1-8M/16M completes its startup, the Status indicator will turn
green. Depending upon optional settings, all channel pairs will either be in the
muted condition or set in a predetermined way. You may then use the Channel
control to enable only the program channels you want to hear.
Front Panel
Each model in the eAMP1-8M/16M series shares the same front panel, differentiated
only by the total number of monitoring meters that can be displayed, either 8 or
16. The front panel is as shown in Figure 2-1.
Figure 2–1: Typical eAMP1-8M/16M Front Panel
1. Interactive LCD Metering Display: A 7" LCD screen allows monitoring of audio
with high resolution bar graph meters of up to 8 or 16 channels, depending upon
model. Also displayed are stereo phase indicators.
2. Speakers: Local near field audio monitoring is achieved through the use of class D
amplifiers. There are two (left/right) speakers. The speaker response may be
adjusted with tone controls in the Speaker Options menu. Refer to the Menu /
Option Touchscreen section of Chapter 2.
3. Headphone Jack: A 1/4" jack for an optional headphone is provided on the front
panel. Speaker audio will be muted when headphones are plugged in. The speaker
audio may optionally be set to not mute, using the Wohler Web GUI. Refer to the
Global Output Options section of Chapter 4. If the speaker audio is set to mute

eAMP1-8M/16M
Page 11
with headphone insertion, and a headphone is plugged into the Headphone Jack,
the following icon will appear at the top of the Audio Meter Display:
4. Volume: This controls the speakers, the headphone, and the analog outputs. As
the Volume control is turned, a graphic appears at the top of the Audio Meter
Display screen, as follows:
Pressing the Volume control mutes the audio and a speaker muted icon appears at
the top the Audio Meter Display: This icon also displays whenever the
Volume control is turned all the way counterclockwise.
5. alance: This controls the relative left/right levels for the monitored stereo mix.
Pressing the knob will bring the balance back to center. It controls the speakers,
the headphone, and the analog outputs. As the alance control is turned, a
graphic appears at the top of the Audio Meter Display as follows:
6. Channel: Turning this control moves a white selection box from channel to channel
on the metering screen. Press the control to solo the highlighted channel. The box
will turn blue and any other boxes will disappear. To remove the solo and return to
the previous monitoring configuration, press the Channel control once again.
7. US : This USB 2.0 Type A connector allows you to use a flash drive (not supplied)
to perform software updates and copy system configurations to another eAMP1-
8M/16M or to a PC. Refer to Appendix A of this manual to learn about performing
a software update.
8. Status: This indicator lights green when the system is powered and ready for use.
A solid or blinking yellow color indicates that the product is starting up. A red color
indicates that a system update is taking place. Refer to Appendix A for procedures
to update software.
Model Differences
Each eAMP1-8M/16M model is differentiated by the monitoring interfaces that it can
support. The function of each connector on the rear panels is described in the next
section. The following is a summary of the monitoring capabilities of each model:
•eAMP1-8M: The eAMP1-8M can monitor up to 8 channels selected from its
input sources. It contains two 3G/HD/SD SDI inputs and outputs, along with
a selected output for the chosen SDI input. As with all models, it contains a
pair of Analog XLR outputs for the program being monitored or for your
choice of any input channels.
•eAMP1-16M: The eAMP1-16M can monitor up to 16 channels selected from
its input sources. It contains two 3G/HD/SD SDI inputs and outputs, along
with a selected output for the chosen SDI input. As with all models, it
contains a pair of Analog XLR outputs for the program being monitored or for
your choice of any input channels.

eAMP1-8M/16M
Page 12
Rear Panel
The Rear Panel is shown in Figure 2-2.
Figure 2-2: Rear Panel Connectors
Balanced XLR
Analog Outputs
Power
Connection
Selected
SDI
Output
SDI Input /
Output
Network
Port
SDI Input /
Output
Power Connection: The eAMP1-8M/16M receives power from an AC inlet, which is a
standard IEC receptacle for 100 to 240 VAC ±10%, 50/60 Hz power connection. Four
regional AC power cords, supplied according to shipping region, are available.
1. SDI Input/Output: These two BNC connectors accept and pass through
the 3G/HD/SD-SDI input signals. nly one may be selected at a time for
monitoring. They incorporate automatic frame rate detection and
selection.
2. Selected SDI Output: This BNC connector outputs the 3G/HD/SD-SDI
input signal that is selected for monitoring.
3. Network Port: This Ethernet port can connect to either a LAN or to a PC
to let you perform metering, monitoring, and configuration remotely. The
Wohler Web GUI is described in Chapter 4 of this manual. Third party
equipment, which can use API commands to view and change product options,
can also be plugged into this port. However, use of the API commands requires
that the PTe Package be purchased. The API is described in Appendix E of
this manual.
4. alanced Analog Outputs: These male XLR connectors provide two
balanced analog outputs: Left and Right . The source of these signals is the
mix of audio as monitored by the internal speakers or any input channels
of your choice. These outputs can either be adjusted by the Volume and
alance controls or configured for a fixed line level output. The Analog
Outputs are standard on the eAMP1-8M/16M. Refer to Figure 2-3 for the
pinout of this connector.
Important:
By design, the supplied AC mains power cord will only plug into a
three-prong grounded outlet for your safety. If the plug does not fit
into the outlet, contact an electrician to replace the obsolete outlet.

eAMP1-8M/16M
Page 13
Figure 2-3: Analog XLR-M utput Connections
Channel Meters and Touch Operations
The audio mixer terminology of “solo” is used in this manual when referring to
muting all but a specific audio channel or pair.
Audio meters are displayed on touchscreen LCD display(s) in up to 8 channel pairs,
as shown in Figure 2-4.
Figure 2-4: Audio Level Meter Screen
1. Channel Source and Channel Number: Above the level meters are the
channel identifiers. They indicate the channel input source and
consecutive channel numbers in the selected source.
2. Speaker Assignment: The speaker assignment for each channel is
shown as follows:
An arrow pointing to the left indicated that this is a left channel and
will be monitored in the left speaker.
An arrow pointing to the right indicated that this is a right channel and
will be monitored in the right speaker.
A square indicates that this is a center channel and will be monitored

eAMP1-8M/16M
Page 14
in both speakers.
3. Source: This indicates the input source of the displayed channel.
4. Loudness Cluster Marker: Loudness Measurement is available if the
PTe Package is purchased. This orange bracket marks which cluster is
currently being measured for Loudness.
5. Loudness Reading: Loudness Measurement is available if the PTe
Package is purchased. This control displays the Loudness of the selected
Cluster. It can also be touched to change which Cluster is being
measured. To do this, touch the green Loudness Reading control. It will
temporarily turn orange. You may then touch the meters in any other
cluster. The Loudness Cluster Marker will then move to that cluster and
its measurement will begin and be displayed. You may then touch the
control again to return it to its green color, restoring normal touch
functioning, or wait 15 seconds for it to time out.
6. Selection Area: Touching the meters of any channel pair will let you
mute, un-mute, or solo the associated channel(s). Colored boxes
surrounding the channel pair or channel indicate what operation is being
performed. The following describes each function:
a. Mute / Un-Mute Selection: The Channel Label is bright green for
each channel that is unmuted. Muting and un-muting by touching is
an alternate action function. Multiple channels may be unmuted at
once. Typically, when the eAMP1-8M/16M is first powered, all of the
channels are muted.
b. Channel Solo: (Method 1) Touch for two seconds any channel you
would like to solo. A blue box will then surround the channel and
that will be the only one you hear. Any white boxes will disappear
and any bright green Channel Labels will dim. Touching another
channel will then move the blue box to it, and it will be soloed.
Touch again to return the combination of monitored channel pairs
to the way they were before you soloed the channel.
c. Channel Solo: (Method 2) Rotating the Channel control will move
a white selection box from channel to channel. Press the Channel
control to solo the selected channel. That channel alone will then be
surrounded by a blue box and it will become the only channel being
monitored. Press the Channel control again or touch the channel
surrounded by the blue box to undo the solo and return the
combination of monitored channel pairs to as it was before you
soloed the channel.
7. Phase Indicators: At the bottom of each channel pair is a Phase
Indicator. The indicators light a dull green if the channels in the pair are
in phase or bright red if they are out of phase. Set which Phase Indicators
appear using the Phase Config Menu or with the System Preferences:
Phase Indicator Configuration tab in the Wohler Web GUI.
8. Menu Selector: Touching the Menu Selector opens the menu used to
set up preferences for operation. Refer to the Menu / Option

eAMP1-8M/16M
Page 15
Touchscreen section of this chapter.
Menu / Option Touchscreen
You may set most options or view a variety of system information using the self-
contained menus. To access this, touch the Menu button which appears on the left
of the level meter screen. Figure 2-5 is a diagram of the menu arrangement, a tree
showing how to reach any menu from the Main Menu. Figure 2-6 shows the Main
Menu.
Figure 2-5: Menu Tree
Meter Scales
Screen
System Options
Loudness Menu
System Details
Screen
Main Menu
Loudness Menu
Preset Favorites
Unit Settings
Speaker Options
Screen
Network Settings
Screen
Factory Reset
Screen
Source Selection
Screen
Unit Settings
Speaker Options
Unit Con iguration
System Update
Screen
System Reboot
Screen
System Options
System Details
Unit Con iguration
Screen
Network Settings
System Reboot
System Update
Factory Reset
Source Select
All Presets
Loudness Meter
Screen
Loudness Settings
Screen
Loudness Meter
Loudness Settings
All Presets
Selection Screen
Preset Favorites
Selection Screen
Analog Con ig
Analog Con ig
Screen
Passcode Settings
Screen
Passcode Settings
Phase Con ig
Phase Con ig
Screen
Meter Scales

eAMP1-8M/16M
Page 16
Main Menu
Touch the Menu button on the display to access the Main Menu. The Main Menu
is shown in Figure 2-6. Note that depending upon whether the PTe Package has
been installed, some of the selections may not appear.
Figure 2-6: Main Menu
Loudness Menu
Loudness Measurement is available if the PTe Package is purchased. Touch the
Loudness Menu button to reach the Loudness Menu Screen, which allows you to
make a selection of either the Loudness Meter Screen or the Loudness Settings
Screen. The Loudness Menu Screen is shown in Figure 2-7.
Figure 2-7: Loudness Menu Screen
Loudness
Loudness Meter
Loudness Settings
Menu
Loudness Meter
Loudness Measurement is available if the PTe Package is purchased. Touch the
Loudness Meter button on the Loudness Menu screen to reach the Loudness Meter
Screen. The Loudness Meter Screen is a more detailed view of the Loudness
Measurement. It is displayed along with the channel meter screen and is shown in
Figure 2-8.

eAMP1-8M/16M
Page 17
A box on the lower right of the screen shows the selected Loudness Source, as does
the orange bracket on the Level Meters screen.
Figure 2-8: ptional Loudness Meter Screen
-24
+9
+6
+3
Re
-3
-6
-9
-12
-15
-18
-21
LU-M
LKFS
LRA 0.1
PROG -21.5
MAX -20.1
TP -20.0
Back
1: Mono #1
Note: In order to calculate loudness accurately, it is crucial that you correctly set
the Channel Function for each channel. Depending upon the designated function of
each channel, its signal levels will contribute differently to the Loudness calculation.
Refer to the Configuration | System Preference | Loudness Configuration tab
in the Web GUI.
The following data is available on the Loudness Meter Screen:
The Program Loudness (shown as -22.5 LKFS in the figure above) is shown digitally
at the upper left of the screen as well as on the meter in the center. At the base of
the meter in the center, one of three indications appears:
1. LU-M: This means that the Loudness Window is set to Momentary.
2. LU-S: This means that the Loudness Window is set to Short Term.
3. LU-C: This means that the Loudness Window is set to Custom. The Loudness
Window is set in the Loudness tab in the Web GUI.
The LU Meter scale colors have the following meaning:
1. Blue: Loudness is lower than the Reference Level by the Alarm Tolerance.
2. Green: Loudness is within the Alarm Tolerance.
3. range: Loudness is greater than the Alarm Tolerance.
Below the digital Loudness meter, in the left column, the following parameters are
also displayed:
1. The Loudness RAnge (LRA) is the measure of variation between the
calculated loudest and softest passage over the program period (shown as
LRA -0.1 above).
2. The Average Loudness is the average of all calculated loudness
measurements made over the Program period (shown as PR G -20.5 above).
3. The Maximum Loudness is the maximum calculated loudness over the
program period (shown as MAX -20.1 above).
4. The Maximum True Peak Loudness is the absolute loudest peak waveform
over the program period (shown as TP -20.0 above).

eAMP1-8M/16M
Page 18
Note: Further and more detailed descriptions of all of the above Loudness terms
may be found in the ITU-R BS.1770-3 loudness standard.
The controls available on the Loudness Meter Screen are:
1. Cluster Select: You may change which Cluster is being measured by simply
touching the green Loudness reading on the Audio Meter screen. It will turn
orange and you will be able to touch other clusters and read their Loudness.
Changing clusters will reset the loudness readings and start a new calculation
on the newly selected cluster.
2. Start: When Manual Mode is selected in the Loudness Settings
screen, from a stopped condition, the Start button will reset the
gathered loudness data and begin a new reading. From a paused
condition, data will not reset as monitoring is resumed.
3. Pause: The Pause button will temporarily stop or continue
gathering loudness data. Data will not be reset using this control.
While paused, Loudness will not be measured.
4. Reset: The Reset button will reset the gathered loudness data. If
it is pressed while a loudness measurement is in progress, a new
reading will then immediately begin.
5. Stop: When Manual Mode is selected in the Loudness Settings
screen, the Stop button will stop gathering loudness data. Data will
be held for viewing and not be reset using this control.
6. ack: Touch the ack button to go to the Loudness Menu.
Loudness Settings
Loudness Measurement is available if the PTe Package is purchased. Touch the
Loudness Settings button on the Loudness Menu to display the Loudness
Settings screen. This screen allows you to change between Manual and
Continuous Monitoring Modes, and also to set the Alarm mode. It also provides a
summary of various Loudness settings, as set in the Configuration | System
Preference | Loudness Configuration tab of the Web GUI. Refer to Figure 2-9.
Figure 2-9: ptional Loudness Settings Screen
The controls and information available on the Loudness Meter Screen are:

eAMP1-8M/16M
Page 19
Monitoring Mode:
1. Manual: Touch the Manual button to enable Manual Mode. This allows you to
measure the loudness of a specific program or segment of a program, such
as a commercial. In this mode, the Start and Stop button on the Loudness
Meter screen can be manually used to begin and end a loudness
measurement interval. The reading for that interval is then held on the
Loudness Meter.
2. Continuous: Touch the Continuous button to enable Continuous Mode. In
this mode, loudness readings are continually made. The Stop button on the
Loudness Meter screen is not active.
Alarm:
1. Over: The Alarm indication will only appear when Loudness has exceeded
the Reference Level by the Tolerance amount.
2. Under: The Alarm indication will only appear when Loudness is below the
Reference Level by the Tolerance amount.
3. oth: The Alarm indication will only appear when Loudness has exceeded or
is below the Reference Level by the Tolerance amount.
4. Off: The Alarm indication will not appear.
Web GUI Loudness Settings: These settings are included on this screen for
reference only. They cannot be changed on this screen.
1. Standard: This is the loudness standard by which the loudness calculation is
made.
2. Reference: This is the set point in the loudness measurement about which
the determination is made as to whether an alarm should be displayed.
3. LRA Window: This is a moving window of time over which the loudness
measurement is made.
4. Window: This may be set to Momentary, Short, or one of 22 values,
ranging from one second to two hours.
Note: Further and more detailed descriptions of all of the above Loudness terms
may be found in the ITU-R BS.1770-3 loudness standard.
When you have completed reviewing or changing the settings, touch the ack
button to return to the Loudness menu.

eAMP1-8M/16M
Page 20
Source Select
Touching the Source Select selection on the Main Menu proceeds to the Source
Select menu, which shows all of the possible sources. The selected source is shown
in a light color. You may simply touch another source in this menu to switch to it.
Figure 2-10 shows the Source Select Menu.
Figure 2-10: Source Select Menu
Touch Menu to exit this menu.
Figure 2-11: Additional Selection Screen:
Menu
SDI CH 1-8 SDI 9-16
Back SDI-1
Touch ack to return to the Source Select menu or touch Menu to return to the
Main Menu.