Wolf ATEX LED Inspection Leadlamp
Operation & Maintenance Instructions
Please Retain – Read Before Use
EC/EU Declaration of Conformity
The Wolf ATEX LED Inspection Leadlamp is a handheld, leaded portable luminaire
and meets all relevant provisions of the:-
a) 94/9/EC Explosive Atmospheres (ATEX Equipment) Directive (up to 19th April 2016)
b) 2014/34/EU Explosive Atmospheres (ATEX Equipment) Directive (from 20th April 2016)
by virtue of the issued EC/EU type examination certificate, demonstrating compliance
with all relevant harmonised standards and essential health and safety requirements.
The Wolf ATEX LED Inspection Leadlamp has a durable aluminium LED module
with a polycarbonate clear lens over the light source, encased in a protective high
impact, anti-static plastic enclosure.
Models are available in a variety of input voltages. Approval is as Group I, M2
equipment for mining applications and Group II, Category 2 equipment for use in
zone 1, 2, 21 and 22 potentially explosive gases, vapours, mists and dusts where
the T4 temperature class/95°C maximum surface temperature permits.
Certification/Approval Code: I M2 Ex eb mb I Mb (-30°C to +55°C)
II 2G Ex eb mb IIC T4 Gb IP67
II 2D Ex mb tb IIIC T95°C Db
EC Type examination certificate: SIRA15ATEX3317X
Notified Body: Baseefa Ltd., Rockhead Business Park,
Staden Lane, Buxton, SK17 9JN, UK.
Notified Body Number: 1180
Harmonised Standards Applied: EN60079-0:2012 +A11:2013, EN60079-7:2015,
EN60079-18:2015, EN60079-31:2014.
Ingress protection level IP67 to EN60529:1992.
The ATEX LED Inspection Leadlamp is compliant with the:-
a) 2004/108/EC EMC Directive (up to 19th April 2016)
b) 2014/30/EU EMC Directive (from 20th April 2016)
To the following harmonised standards BS EN 55015:2013, BS EN 61000-3-2:2006
+A2:2009, BS EN 61000-3-3: 2013 and BS EN 61547: 2009.
Alex Jackson – Managing Director
Wolf Safety Lamp Company Ltd.
IECEx Certification Scheme
Certificate Number: IECEx SIR15.0115X
Certification/Approval Code: Ex eb mb I Mb (-30°C to +55°C)
Ex eb mb IIC T4 Gb IP67
Ex mb tb IIIC T95°C Db
Standards Applied: IEC60079-0:2011, IEC60079-7:2015,
IEC60079-18:2014, IEC60079-31:2013.
Ingress protection level IP67 to IEC60529:1992.
SPECIAL CONDITIONS OF USE (X) CONDITION
This equipment shall not be used in mining locations where oils, greases or
hydraulic liquids may be present.
EQUIPMENT USE
1. Check the rating label to ensure the ATEX LED Inspection Leadlamp is
suitable for the supply provided, ambient temperature present and the
environmental conditions.
2. Polycarbonate parts, check Ex area for potential contact to corrosive
and/or aggressive substances.
3. The ATEX LED Inspection Leadlamp has a single metric M20 x 1.5 entry.
Use only specified gland (No. 7 on Spare Parts).
4. Ensure any replacement cable is rated for the lower ambient temperature
the ATEX LED Inspection Leadlamp will be used in and a +80°C minimum
upper rating.
5. Inspect cable for damage at regular intervals.
6. Damaged equipment should be withdrawn and repaired as necessary
before being put back in to service, in accordance with EN60079-17.
7. LED Inspection leadlamps must not be opened in Hazardous Areas.
MAINTENANCE
CAUTION: HOT – Allow lamp to cool before dis-assembly.
1. Isolate the ATEX LED Inspection Leadlamp from the power supply before
carrying out any maintenance work.
2. The Encapsulated electronics in the LED module is a sealed unit and cannot
be repaired.
FAULT FINDING
If an ATEX LED Inspection Leadlamp fails to function, check input cable continuity
and terminations in the plug and LED module.
DISPOSAL OF WASTE MATERIAL
Disposal of packaging, and ATEX LED Inspection Leadlamp products
should be carried out in accordance with national regulations. (WEEE).
The Wolf Safety Lamp Co. Ltd has a policy of continuous product
improvement. Changes in design details may be made without prior notice.
A copy of these instructions with any relevant revisions can be found at
www.wolf-safety.co.uk
2
SPARE PARTS
Item Part Part Description Quantity
No. No. Required
1 SP-466 High impact plastic body enclosure including 1
fixing screws/nuts and back accessory nut
2 SP-480 Polycarbonate lens cover including gasket 1
and fixing screws
3 SP-412 Rear cover gasket 1
4 W-463 Ex terminal block and mounting screw 1
5 SP-440 Hook and filler plug 1
6 SP-460 Gland with seal (M20 x 1.5) 1
7 SP-444 Handle grommet 1
8 SP-414 Outer lens bezel 1
9 SP-510/10 Cable 10m 2x core 1.5mm² 1
10 SP-612 Enclosure Screw Kit 1
11 SP-614 LED Module Screw Kit 1
12 SP-628 Protection sleeve kit (5 sleeves & 10 cable ties) 1
13 SP-626 Cage with a 88mm diameter magnet 1
14 SP-624 66mm diameter magnet 1
15 SP-620 Cage and fixing bolt 1
PROTECTION SLEEVE
12
CAGE AND OPTIONAL 88mm DIAMETER MAGNET
Cage fits over sleeve
3
66mm DIAMETER MAGNET
14
Ø66mm
EN IEC 60079-17
IMPORTANT
Fit only genuine WOLF accessories and spare parts purchased
from the manufacturer, unauthorised modifications or spare
parts will invalidate certification.
10
10
10
11
11
11
11
101010
11
11
Maximum M8
Thread Length for
Accessories = 7mm
Maximum M8 Thread Length
for Accessories = 7mm
15
Ø88mm
13
