Wonwoo WCM-121N Installation instructions

Installation / Operating Manual
12X Day&Night MINl PTZ CAMERA
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use
Distributed by
388057165
PRINTED IN KOREA

USER INFORMATION
02 MIN PTZ CAMERA 03 MIN PTZ CAMERA
CONTENTS
3p.
4p.
5p.
6p.
6p.
6p.
7p.
8p.
9p.
11p.
11p.
11p.
12p.
14p.
16p.
18p.
19p.
21p.
22p.
25p.
35p.
35p.
36p.
37p.
38p.
1. USER INFORMATION
2. FEATURES
3. PRECAUTIONS
4. PTZ SETTING & INSTALLATION
Box Contents
Preparation for installation
PTZ setup (DIP switch)
RS-485 Setting
Installation & Cable connection
5. ON SCREEN DISPLAY MENU
Motion menu
Preset
Tour
Scan
Pattern
Area
Alarm
Privacy
Dome menu
Camera menu
Clear menu
PTZ reset
6. DIMENSIONS
7. SPECIFICATIONS
8. QUICK COMMAND
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
FCC COMPLIANCE STATEMENT
INFORMATION-This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference a this own expense.
WARNING-Changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
* This installation should be made by a qualified service person and should conform to all local codes.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

04 MIN PTZ CAMERA 05 MIN PTZ CAMERA
FEATURES PRECAUTIONS
The camera is a compact 12X Day&Night PTZ camera which can be applied in
any application. This camera is packaged in a rugged aluminum die-cast housing with a
built-in high speed pan/tilt mechanism , which provides faster and more coverage than
multiple fixed cameras.
This camera offers a number of advanced features and functions; OSD menu control, Preset,
Tour, Scan, and Pattern. By utilizing the 63 programmable Presets, 4-minute Pattern
auto-pan and continuous scan mode, the camera can cover a broader range.
• 1/4" 613K pixels Sony Super HAD II (Double scan) CCD
• Progressive scan 612,688 pixel
• 12x Optical Zoom, Digital 32x zoom
• High Resolution 700 TV lines - HR 7 mode
• Day & Night (ICR)
• Wide Dynamic Range(512x)
• Digital Noise Reduction(2D+3D)
• Privacy Mask Function
• Endless Pan rotation (-45 ° to 90 ° Tilt angle)
• Up to 63 programmable presets
• less than ±0.1° Preset Accuracy
• 8 programmable Tours, 4 Patterns
• Alarm - Move the camera to programmed Preset position
with Alarm trigger.(Max. 2)
• 4 Scan(Programmable speed and diagonal scan)
• Programmable Privacy Masking(4 Zones)
• RS-422, RS-485 communication
• Multiple protocol (Pelco-D, Pelco-P, Wonwoo)
• Built-in Menu System for Setup of Programmable Functions
• Mechanical Auto Flip
• Programmable Zoom Speed(Optional Update tool)
• DC 12V, 1.5A
• IP64
• E-mark for Vehicle Application
Do use the camera under conditions where temperatures are within -10°C to 50°C.
Under high temperatures, ensure proper ventilation.
Do not install the camera in extreme temperature conditions.
Do not install or use the camera in an environment where the
humidity is high.
Do not install the camera under unstable lighting conditions.
It can cause the image quality to be poor.
Severe lighting change or flicker can cause the camera to work improperly.
Never use the camera close to a gas or oil leak.
Do not disassemble the camera.
It can cause malfunctions to occur.
There are no user-serviceable parts inside it.
Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
Do not allow direct sunlight into the camera.
It can damage CCD.
Do not expose the camera to rain or spill beverages on it.
Note
If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode
the electronic components.
If the camera is exposed to spotlight or object reflecting the strong light,
smear or blooming may occur.
Please check the power whether it satisfies the normal specification before
connecting the camera.

PTZ SETTING & INSTALLATION
06 MIN PTZ CAMERA 07 MIN PTZ CAMERA
PTZ SETTING & INSTALLATION
SW502
1. Reserved
2. Set the RS-485 Termination
ON: RS-485
OFF: Null.
3. Select Installation mode
ON: Bottom, OFF: TOP mode
4. Select Video format
ON: PAL, OFF: NTSC
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears to
have been damaged in shipment, replace it properly in its carton and notify the shipper.
Save the shipping carton and packaging material. They are the safest material in which to make future shipments
of the equipment. Keep this Installation and Operating Manual.
Camera should be installed by qualified service personnel in accordance with all local
and federal electrical and building codes. The system should be installed according to as
described
Camera Installation cable Manual Installation bracket
1-loose
proof screw
3- Installation bracket
Fixing screws
RS-485
connector
To install and use the camera, the following is required. (NOT included in box)
1) Power adaptor (DC12V, Over 2A)
The power adaptor should be DC12V and over 2A. For better image quality and lower
failure rate, min 2A or higher is required.
2) BNC cable for video signal.
BNC connectors and coaxial cables are closely related with the quality of the camera image.
3) RS-485 communication cable (Twist pair)
According to the RS-485 standards, the maximum cable length is 1.2Km
1.PTZ setup (DIP switch)
To set the camera ADDRESS and PROTOCOL, open the cap on the left side of PTZ. There are 12 DIP switches,
3 dial switches and 1 connector for the camera program update.
ⓐ(SW502) : Set the termination, Camera installation mode and Camera video format.
ⓑ(SW501) : Set the communication protocol, baud rate and protocol parity
ⓒ(SW503~505) : Set the camera address
ⓓ: Camera program update port (Need Special update tool kit)
1234 43215678
SW501
SW502
0
9
8
7
6
5
4
3
2
1
1
0
9
8
7
6
5
4
3
2
7
8
9
0
2
3
4
5
6
1
1234 43215678
SW501
SW502
0
9
8
7
6
5
4
3
2
1
1
0
9
8
7
6
5
4
3
2
7
8
9
0
2
3
4
5
6
1
ⓐSW502
12 34
-- ON
ON
BOTTOM
ON
PAL
ON
- - OFF
OFF
TOP
OFF
NTSC
OFF
Reserved
TERMINATION
INSTALLATION
VIDEO
FORMAT
Installation mode select
<BOTTOM> <TOP>
Box Contents
Preparation for installation
ⓒⓓ
ⓐⓑ
Alarm/Relay
connection cable
Fixing screw
for safety wire

08 MIN PTZ CAMERA 09 MIN PTZ CAMERA
PTZ SETTING & INSTALLATION PTZ SETTING & INSTALLATION
2. Installation & Cable connectionRS-485 Setting
For RS-485 communication, the first and last devices (PTZ or keyboard controller) should be terminated
for more stable data communication by setting the DIP switches. Without proper termination, there is
potential for control signal error. Total length of the cable for communication should NOT exceed 1.2Km
(twisted pair). To extend the distance, use a reliable RS-485 repeater.
SW501
12 345 678
NONE OFF OFF 2400bps OFF OFF OFF WTX (WONWOO) OFF OFF OFF
EVEN ON OFF 4800bps OFF OFF ON WPD (PELCO-D) OFF OFF ON
OLD OFF ON 9600bps OFF ON OFF WPP (PELCO-P) OFF ON OFF
NONE ON ON 19200bps OFF ON ON
38400bps ON OFF OFF
57600bps ON OFF ON
PROTOCOLBAUDRATEPARITY
SW503 : 100 digit of camera address
SW504 : 10 digit of camera address
SW505 : 1 digit of camera address
ex) If SW503=1, SW504=2, SW505=5
then, the Camera Address = 125
* Factory default address is 001
ⓑSW501 (Protocol select)
ⓒ SW503~SW505 (PTZ address select)
Precautions for Installation
- Ensure that the installation location can safely bear min. 4Kg and its installation fittings.
- When installing the ceiling bracket, use the supplied fixing screws or similar screw head.
- Do not drop the product during installation. Do not allow anyone to stand below the installation area.
STEP 1
STEP 2
STEP 3
Prepare the installation accessories provided in the
camera box. The Video and RS-485 control cables,
Power adaptor(DC12V, 2A) and installation tools are
necessary to complete the installation.
For cable connection, make a hole
(Hole size 25mm~30mm) in the ceiling where you
want to install the camera.
Attach the installation bracket with the included
3 fixing screws.
The external cables (video cable, controller cable
and power) should be inserted into the center hole
of the bracket.
Connect the external cables to included installation
cables (Video, DC12V power, RS-485 communication,
Alarm-in, and Relay-out) For more detail connection,
please see below connector description and chart.
STEP 1.
STEP 2.
STEP 3.
Alarm and Relay
Black relay 2 (NO)
Brown relay 2 (COM)
Red relay 1 (NO)
Orange relay 1 (COM)
Yellow Alarm 2 (NO)
Green Alarm 1 (NO)
Blue Alarm (COM)
Video out
RS-485
DC12V
Alarm / Relay

11 MIN PTZ CAMERA
On Screen Display MenuPTZ SETTING & INSTALLATION
STEP 4
STEP 5
STEP 6
Connect the camera with the provided Installation
cable. The arrow mark on the cable connector
should be facing upwards (see diagram).
After cable connection, close the cable latch.
STEP 4.
STEP 5.
STEP 6.
(CAUTION) For safety reasons, the power should be
off during the installation. There is NO power
button on the camera.
Connect the metal safety wire from the bracket to
the camera with the included screw.
Pull the cable into the ceiling hole and attach the
camera to the bracket by turning clockwise.
After mounting the camera to the bracket, fix the
camera with the supplied fixing screw.
10 MIN PTZ CAMERA
(NOTICE) To make cabling without ceiling hole(Side cabling),
please cut off the cabling guide of PTZ. (see picture)
1 Initialize
2 Motion Menu
When the device is powered on, you can check the address,
version, protocol and video setting values.
MOTION MENU
The preset function is that the camera memorizes positions
of the pan/tilt and zoom. This function is a representative
function of the speed dome which can find memorized
preset positions just by selecting the preset number.
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
EXIT
< NEAR / RIGHT MOTION >
1) Set preset.
SAVE CLR BACK EXIT
PRESET MENU
PRESET NO
LABEL
POSIRION
FOCUS
: 001 UNDEFINE
: PRESET 001
: 019.9, 005.4
: AUTO
< NEAR / RIGHT PRESET NO >
- Set PRESET Number
PRESET SELECT 1
< SEL NEAR/MOVE JOYSTICK >
P001
P007
013
019
025
031
037
043
049
P002
P008
014
020
026
032
038
044
050
P003
009
015
021
027
033
039
045
051
P004
010
016
022
028
034
040
046
052
P005
011
017
023
029
035
041
047
053
P006
012
018
024
030
036
042
048
054
Preset No. : Max. 63 positions can be stored and the each
position can be assigned as a defined preset No.
Label : Each preset can have its own label name.
Position : It displays the coordinates to position the assigned
preset.
Focus : It enables to set the camera focus for each preset
position.
NEAR
NEAR
Press key.
Select number by using joystick and press key.
INITIALIZE
ADDRESS
VERSION
VIDEO
PROTOCOL
>>PAN OFFSET . . . . . . .
>>TILT OFFSET. . .
: 001 <TOP>
: 8.02
: NTSC EMC
: WPD 2400,N,1
NORMAL SETTING

On Screen Display Menu On Screen Display Menu
12 MIN PTZ CAMERA 13 MIN PTZ CAMERA
- LABEL Setting
- POSITION Setting
PRESET POSITION
LABEL : PRESET 001
POSITION : 019 .9, 005.4
< EXIT FOCUS NEAR >
- FOCUS Setting
SAVE CLR BACK EXIT
PRESET MENU
PRESET NO
LABEL
POSIRION
FOCUS
: 001 DEFINE
: PRESET 001
: 019.9, 005.4
: AUTO
< CHANGE UP/DN SEL NEAR >
2) TOUR
The Tour function consists of several presets run by turn.
Maximum of 8 Tour functions are toured in order.
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT BACK
< NEAR / RIGHT TOUR >
- TOUR EDIT
NO
01
02
03
04
05
06
07
08
PRESET
P001
P002
P003
P004
P005
P006
P007
P008
SPEED
63
63
63
63
63
63
63
63
DWELL
02
02
02
02
02
02
02
02
TOUR MENU
SAVE CLR BACK EXIT
< SEL NEAR PRESET LEFT >
PRESET LABEL EDIT <001>
)
L
X
0
A
M
Y
1
B
N
Z
2
C
O
.
3
D
P
/
4
E
Q
,
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
9
J
V
>
(
K
W
@
LABEL : PRESET 001
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
Define the Preset position
a. Move to the set-up window
or
b. Move and set the position c. Set & Back
NEAR NEAR
TOUR MENU
< SEL NEAR/MOVE JOYSTICK >
P001
P007
013
019
025
031
037
043
049
P002
P008
014
020
026
032
038
044
050
P003
009
015
021
027
033
039
045
051
P004
010
016
022
028
034
040
046
052
P005
011
017
023
029
035
041
047
053
P006
012
018
024
030
036
042
048
054
NEAR
NEAR
Press key.
Select focus by using joystick and press key.
NEAR
NEAR
Press key.
Select number by using joystick and press key.
NEAR
NEAR
Press key.
Select character by using joystick and press key.
- TOUR NO
- LABEL
TOUR MENU
TOUR NO
LABEL
TOUR EDIT
: 01 DEFINE
:
SAVE CLR BACK EXIT
< NEAR / RIGHT TOUR NO >
TOUR MENU
TOUR NO
LABEL
TOUR EDIT
: 01 DEFINE
:
SAVE CLR BACK EXIT
< NEAR / RIGHT TOUR NO >
TOUR LABEL EDIT <01>
)
L
X
0
A
M
Y
1
B
N
Z
2
C
O
.
3
D
P
/
4
E
Q
,
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
9
J
V
>
(
K
W
@
LABEL
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
It’s available to set the desired label, displayed on the executing screen of Tour.
After the label is set, push the NEAR button to exit.
Select the Tour number
Move : Select :
NEAR
Set the Tour Label
Move : Select : or or Delete : or
JOYSTICK JOYSTICK
TELE WIDE
03 04 05 06
T02
08
T01
07
TOUR MENU
< SEL NEAR/MOVE JOYSTICK >
AUTO / MANUAL / ONE SHOT

On Screen Display Menu On Screen Display Menu
15 MIN PTZ CAMERA 14 MIN PTZ CAMERA
By using scan function, the camera moves between 2 positions if there is no PTZ command after
passing the assigned dwell time. The scan function
runs and the camera moves from the position
assigned as the start point to the position
assigned as the end point in CW (Clockwise) direction.
3) Scan
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT BACK
< NEAR / RIGHT SCAN >
< NEAR / RIGHT SCAN >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 UNDEFINE
:
: XXX.X, XXX.X
: XXX.X, ---
: XX
: XX
: NONE
SAVE CLR BACK EXIT
- SCAN NO
It’s available to set the desired label, displayed on the executing screen of scan.
After the label is set, push NEAR button to go out.
- LABEL
< NEAR / RIGHT LABEL SEL >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 UNDEFINE
:
: XXX.X, XXX.X
: XXX.X, ---
: XX
: XX
: NONE
SAVE CLR BACK EXIT
- END POSITION
- START POSITION
< NEAR / RIGHT END POS >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, ---
: 60
: 02
: AUTO
SAVE CLR BACK EXIT
SCAN END POSITION
POSITION : 000 .0
< EXIT FOCUS NEAR >
- SPEED
< NEAR / RIGHT MOVE SPEED >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, ---
: 60
: 02
: AUTO
SAVE CLR BACK EXIT
Set the Scan speed
Increase : or
Decrease : or
JOYSTICK
JOYSTICK
It adjusts the moving speed from 0~63 steps.
SCAN LABEL EDIT <01>
)
L
X
0
A
M
Y
1
B
N
Z
2
C
O
.
3
D
P
/
4
E
Q
,
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
9
J
V
>
(
K
W
@
LABEL :
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
Move : Select : or or
JOYSTICK
Delete : or
JOYSTICK
TELE WIDE
or
Define the End pan position
① Select End Pos menu ② Move and set the position ③ Go back
NEAR NEAR
Define the Start pan position
① Select Start Pos menu ② Move and set the position ③ Go back
or
NEAR NEAR
TELE
WIDE
- Scan No. : Max. 4 Scans can be stored.
- Label : The each Tour can have its own label name.
- Start position : Assign the coordinate of the Scan starting
position.
- End position : Assign the coordinate of the Scan ending position.
- Move Speed : It enables to set the running speed in the each
coordinate.(1~63)
- Dwell : The Scan function runs after the dwell time without any
camera movement.
- Focus : It enables to set the camera focus.
< NEAR / RIGHT START POS >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, ---
: 60
: 02
: AUTO
SAVE CLR BACK EXIT
SCAN START POSITION
POSITION : 000 .0, 000 .0
< EXIT FOCUS NEAR >
SCAN MENU
01 02 03 04
< SEL NEAR/MOVE JOYSTICK >

16 MIN PTZ CAMERA 17 MIN PTZ CAMERA
On Screen Display Menu On Screen Display Menu
- DWELL
< NEAR / RIGHT DWELL >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, ---
: 60
: 02
: AUTO
SAVE CLR BACK EXIT
- FOCUS
< NEAR / RIGHT FOCUS MODE >
SCAN MENU
SCAN NO
LABEL
START POS
END POS
SPEED
DWELL
FOCUS
: 01 DEFINE
:
: 000.0, 000.0
: 000.0, ---
: 60
: 02
: AUTO
SAVE CLR BACK EXIT
The pattern function memorizes user’s random moving path and zoom ratio.
Total recording time limit is 60secs and maximum 4 pattern functions are toured in order.
4) PATTERN
＊PATTERN NO : 1~4 Patterns can be stored in keyboard menu.
＊LABEL : The each pattern can have its own label name.
＊RECORD : Movement by joystick and preset movement can be
memorized in a pattern.
＊PLAY : To revive the pattern during the recorded time.
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT BACK
< NEAR / RIGHT PATTERN >
- PATTERN NO
PATTERN MENU
PATTERN NO
LABEL
RECORD
PLAY
: 01 UNDEFINE
:
< NEAR / RIGHT PATT NO >
SAVE CLR BACK EXIT
01 02 03 04
PATTERN MENU
< SEL NEAR/MOVE JOYSTICK >
Select the pattern number
Move : Select :
- LABEL
PATTERN MENU
PATTERN NO
LABEL
RECORD
PLAY
: 01 UNDEFINE
:
< NEAR / RIGHT LABEL SEL >
SAVE CLR BACK EXIT
- RECORDING
PATTERN MENU
PATTERN NO
LABEL
RECORD
PLAY
: 01 DEFINE
: <00SEC>
< NEAR / RIGHT RECORD >
SAVE CLR BACK EXIT
03/60
EXIT : NEAR 005 .8,000 .0
PATTERN RECORD
- PLAY
PATTERN MENU
PATTERN NO
LABEL
RECORD
PLAY
: 01 DEFINE
: <00SEC>
< NEAR / RIGHT PLAY >
SAVE CLR BACK EXIT
Play back the recorded pattern data
PATTERN LABEL EDIT <01>
)
L
X
0
A
M
Y
1
B
N
Z
2
C
O
.
3
D
P
/
4
E
Q
,
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
9
J
V
>
(
K
W
@
LABEL :
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
NEAR
Set the pattern Label
Move : Select : or or
JOYSTICK JOYSTICK
Delete : or
It’s available to set the desired label, displayed on the executing screen of pattern.
After the label set, push NEAR button to go out.
TELE WIDE
Record and Save the User’s random pattern data
① Select the “Record” Menu
or
② Move and record the pattern ③ Set & Back
NEAR NEAR
NEAR
Select time by using joystick and press key.
NEAR
Select focus by using joystick and press key.
The Scan function runs after the dwell time without any camera
movement.
Tiime (0 ~60 sec )
It enables to set the camera focus.(AUTO / MANUAL / ONESHT )

19 MIN PTZ CAMERA 18 MIN PTZ CAMERA
On Screen Display Menu On Screen Display Menu
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT BACK
< NEAR / RIGHT AREA >
The area function means that it displays the area name between two programmed pan positions.
Maximun 4 area functions are toured in order.
5) AREA
- AREA NO
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
: 01 UNDEFINE
:
: XXX.X
: XXX.X
< NEAR / RIGHT AREA NO >
SAVE CLR BACK EXIT
- LABEL
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
: 01 UNDEFINE
:
: XXX.X
: XXX.X
< NEAR / RIGHT LABEL EDIT >
SAVE CLR BACK EXIT
AREA LABEL EDIT <01>
)
L
X
0
A
M
Y
1
B
N
Z
2
C
O
.
3
D
P
/
4
E
Q
,
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
9
J
V
>
(
K
W
@
LABEL :
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
- STOP PAN POSITION
AREA START POSITION
POSITION : 000 .0, 000 .0
< EXIT FOCUS NEAR >
- START PAN POSITION
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
: 01 DEFINE
:
: 000.0
: 000.0
< MOVE NEAR / JOYSTICK>
SAVE CLR BACK EXIT
AREA STOP POSITION
POSITION : 000 .0, 000 .0
< EXIT FOCUS NEAR >
AREA MENU
AREA NO
LABEL
START PAN POS
STOP PAN POS
: 01 DEFINE
:
: 000.0
: 000.0
< MOVE NEAR / JOYSTICK>
SAVE CLR BACK EXIT
※“Save” above setting area data to the memory.
- "Save" above setting data to the memory.
- "CLR" means above setting pattern data will not be saved and be cleared.
- "BACK" means it goes back to the previous menu.
- "EXIT" means it goes out of the MENU
Define the start pan position
① Select the “START PAN POS” menu
or
② Move and set the position ③ Set & Back
※ Camera will move to clockwise direction only when START setting.
Define the stop pan position
① Select the “STOP PAN POS” Menu ② Move and set the position ③ Set & Back
＊ALARM NO : 1~2 Alarms can be stored.
＊LABEL : The each alarm can have its own label name.
＊PRESET NO : Assign the preset No. to run when alarm is triggered.
MOTION MENU
PRESET
TOUR
SCAN
PATTERN
AREA
ALARM
PRIVACY
EXIT BACK
< NEAR / RIGHT ALARM >
The alarm function means that the camera moves to the programmed
preset position by the alarm trigger.
Maximum 2 alarm functions are toured in order.
6) ALARM
Select the area number
Move : Select :
NEAR
Set the area Label
Move : Select : or or
JOYSTICK
Delete : or
JOYSTICK
After the label set, push NEAR button to go out.
TELE WIDE
NEAR NEAR
or
NEAR NEAR
01 02 03 04
AREA SELECT
< SEL NEAR/MOVE JOYSTICK >

On Screen Display Menu On Screen Display Menu
20 MIN PTZ CAMERA 21 MIN PTZ CAMERA
- ALARM NO
02
ALARM SELECT
< SEL NEAR/MOVE JOYSTICK >
AREA MENU
ALARM NO
LABEL
PRESET NO
: 01 UNDEFINE
:
: XXX.X
< NEAR / RIGHT ALRAM NO >
SAVE CLR BACK EXIT
01
The alarm function means that the camera moves to the programmed preset position by the alarm trigger.
Maximum 2 alarm functions are toured in order.
Move : Select :
- LABEL
AREA MENU
ALARM NO
LABEL
PRESET NO
: 01 UNDEFINE
:
: XXX.X
< NEAR / RIGHT LABEL EDIT >
SAVE CLR BACK EXIT
ALARM LABEL EDIT <01>
)
L
X
0
A
M
Y
1
B
N
Z
2
C
O
.
3
D
P
/
4
E
Q
,
5
F
R
+
6
G
S
-
7
H
T
=
8
I
U
<
9
J
V
>
(
K
W
@
LABEL :
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
Set the alarm label
Move : Select : or or Delete : or
JOYSTICK JOYSTICK
It’s available to set the desired label, displayed on the executing screen of alarm.
After the label is set, push the NEAR button to exit.
- PRESET NO
ALARM MENU
ALARM NO
LABEL
PRESET NO
: 01 DEFINE
:
: 001
SAVE CLR BACK EXIT
< MOVE NEAR / JOYSTICK>
P001P002P003P004P005P006
P007P008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
PRESET SELECT 1
< SEL NEAR/MOVE JOYSTICK >
※ “Save” above setting alarm data to the memory.
- "Save" above setting data to the memory.
- "CLR" means above setting pattern data will not be saved and be cleared.
- "BACK" means it goes back to the previous menu.
- "EXIT" means it goes out of the menu.
Define the preset position with alarm trigger
① Select the “Preset No”
or
② Move and set the position ③ Set & Back
- PRIVACY NO
7) PRIVACY setting
＊PRIVACY NO : To protect privacy, Max. 4 privacy can be created
on the arbitrary position to hide objects such as windows, shops
or private house. With spherical coordinates system, powerful
privacy zone masking function is possible.
＊POSITION : Adjust the mask position
MOTION MENU
PRESET
TOUR
SCAN
PATTEN
AREA
ALARM
PRIVACY
EXIT BACK
< NEAR / RIGHT PRIVACY >
PRIVACY MENU
PRIVACY NO
POSITION : 01 UNDEFINE : XXX .X, XXX .X
< NEAR / RIGHT PRIVACY NO >
SAVE CLR BACK EXIT
01 02 03 04
PRIVACY SELECT
< SEL NEAR/MOVE JOYSTICK >
- POSITION
PRIVACY MENU
PRIVACY NO
POSITION : 01 DEFINE : 000 .0, 000 .0
< NEAR / RIGHT PRIVACY NO >
SAVE CLR BACK EXIT
PRIVACY POSITION
POSITION : 000 .0, 000 .0
< EXIT FOCUS NEAR >
MASK SIZE <OPEN/CLOSE>
NEAR
TELE WIDE
NEAR NEAR
* Press key to set privacy number and press key again to go out the menu.
NEAR NEAR
OPEN CLOSE NEAR
*Adjust masking size by using , keys and press key to go out the menu.

On Screen Display Menu On Screen Display Menu
23 MIN PTZ CAMERA 22 MIN PTZ CAMERA
3 Dome Menu
Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” menu.
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
EXIT
< NEAR / RIGHT DOME >
Move : Select : or or Delete : or
JOYSTICK JOYSTICK
After the label set, push NEAR button to go out.
<STORE TELE MOVE JOY>
<DEL WIDE BACK NEAR>
TITLE SET
LABEL :
2) POWER UP ACTION
When this function is ON, the camera memorize the latest action
and restore it from sudden power failure.
TELE WIDE
＊TIME (MIN) : The park time can be assigned
from 5 min to 60 min(5min,10min ~60min)
※When MOTION is operating, PARK ACTION is not working. (without AREA and PRIVACY )
: This function enables to locate the camera to specific position
automatically if operator doesn’t operate the controller for a while.
- TIME
3) PARK ACTION
< NEAR / RIGHT PARK TIME >
SAVE BACK
PARK MENU
TIME
FUNCTION
NUMBER
: 02MIN
: PRESET
: 01
: Can select one of the motion functions, Preset, Tour, Pattern
and Scan.
- FUNCTION
< NEAR / RIGHT FUNCTION >
SAVE BACK
PARK MENU
TIME
FUNCTION
NUMBER
: 02MIN
: PRESET
: 01
: The number of selected motion function.
- PRESET : 01~63
- TOUR : 01~08
- SCAN :01 ~ 04
- PATTERN : 01 ~ 04
- NUMBER
< NEAR / RIGHT NUMBER >
SAVE BACK
PARK MENU
TIME
FUNCTION
NUMBER
: 02MIN
: PRESET
: 01
4) DISPLAY ON/OFF
DISPLAY ON/OFF SET
TITLE
ZOOM
PRESET
TOUR
SCAN
PRIVACY
PATTERN
AREA
ALARM
POSITION
ACTION
*
< * >
< * >
< * >
< * >
< * >
< * >
< * >
< * >
< * >
< >
<ON TELE MOVE JOY >
<OFF WIDE BACK NEAR>
You can select the OSD ON to shown on the screen or clear by selecting OFF in this function.
OSD ON : OSD OFF: Select :
< NEAR / RIGHT FUNCTION >
SAVE BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF
< NEAR / RIGHT FUNCTION >
SAVE BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF
< NEAR / RIGHT SUB MENU >
SAVE BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF < NEAR / RIGHT SUB MENU >
SAVE BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF
NEARTELE WIDE
1) Set the Dome camera title
NEAR
Select ON/OFF by using joystick and press key.
NEAR
Select ON/OFF by using joystick and press key.

24 MIN PTZ CAMERA 25 MIN PTZ CAMERA
On Screen Display Menu On Screen Display Menu
5) SPEED BY ZOOM
6) PRESET FREEZE
Pan and tilt speed can be changed depending on zoom magnification.
ON will slow down the speed of Pan/Tilt and OFF will increase the
Pan/Tilt speed.
- SPEED BY ZOOM
Video out for start & stop points only and during camera movement the screen
is shown paused image.
- PRESET FREEZE
NEAR
Select ON/OFF by using joystick and press key.
NEAR
joystick and press key.
NEAR
Select ON/OFF by using joystick and press key.
7) FACTORY SET
< NEAR / RIGHT FUNCTION >
SAVE CLR BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF
Restore all of setting value to the factory default.
All of existing setting value would be erased.
D-ZOOM (Digital Zoom)
- Magnification of the digital zoom can be switched On and Off.
- It is recommended that the digital zoom should be set up before the preset operation.
- As the digital zoom magnification increases, the image quality is lowered.
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
< NEAR / RIGHT ▶ ZOOM SET >
▷
▷
▷
▷
▷
▷
▷
SAVE BACK EXIT
CAMERA MENU
ZOOM MENU
ZOOM SPD : 7
D-ZOOM : ON
BACK
< NEAR / RIGHT
▶
ZOOM SPD>
ZOOM MENU
ZOOM SPD : 7
D-ZOOM : ON
BACK
< NEAR / RIGHT
▶
D-ZOOM >
ZOOM SPEED : Select from 1 step to 7 steps
USER (Standard speed)
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
1) ZOOM MODE
Zoom speed can be set and decided using of digital
zoom function.
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
4 Camera Menu
Camera menu is subject to be changed without prior notice to upgrade and quality increase
and we may use slip sheet for the change.
Please check the camera version and the slip sheet if the camera menu and this manual
menu is not matched.
- ZOOM SPEED
- D-ZOOM
< NEAR / RIGHT FUNCTION >
SAVE BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF
< NEAR / RIGHT FUNCTION >
SAVE BACK EXIT
DOME MENU
TITLE :
POWER UPACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
PRESET FREEZE
FACTORY SET
: ON
: OFF

27 MIN PTZ CAMERA 26 MIN PTZ CAMERA
On Screen Display Menu On Screen Display Menu
In focus menu, you can set up the focus mode among Auto,
One Push or Manual.
2) FOCUS
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
FOCUS SET >
AUTO: The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode.
In the auto focusing mode, zoom key operation is not
recognized as the input of the focus key.
One Push: It will be focused in about 5 seconds after zooming,
panning, and return to MANUAL mode automatically.
This is for focusing accurately after zooming.
Manual: In the manual mode, users can adjust the camera
focus manually.
Infinity: infinity focus is the state where a lens forms an image
of an object an infinite distance away.
This corresponds to the point of focus for parallel rays.
Set the speed for camera focusing.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : 5
NEAR LIMIT : XXXX
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
FOCUS MODE >
FOCUS MENU
FOCUS MODE : MANUAL
FOCUS SPD : 3
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
FOCUS SPD >
Set the focus distance. (1.0 CM ~ OVERINF)
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : 3
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
NEAR LIMIT >
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
- NEAR LIMIT
- FOCUS MODE
- FOCUS SPEED
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
AE SET >
3) AUTO EXPOSURE
AUTO EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
AE MODE >
AF MODE: Set the auto focus mode
SENSITIVITY: Set the sensitivity of focus
Select AUTO,MANUAL,SHUTTER or IRIS.
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : 3
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
AF MODE >
FOCUS MENU
FOCUS MODE : AUTO
FOCUS SPD : 3
NEAR LIMIT : 10CM
AF MODE : NORMAL
SENSITIVITY : NORMAL
BACK
< NEAR / RIGHT
▶
SENSITIVITY >
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
AE setting is a function adjusting shutter speed according
to subject’s brightness to get standard amount of exposed
light.
- AF MODE
- SENSITIVITY
- AE MODE

On Screen Display Menu On Screen Display Menu
28 MIN PTZ CAMERA 29 MIN PTZ CAMERA
AE MODE : MANUAL
SHUTTER SPD : 1/50
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : 28dB
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
SHUTTER SPD >
AE MODE : MANUAL
SHUTTER SPD : 1/50
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : 28dB
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
SLOW SHT >
AE MODE : IRIS
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : 07
GAIN LEVEL : 28dB
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
IRIS LEVEL >
AE MODE : IRIS
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : 07
GAIN LEVEL : 28dB
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
GAIN LEVEL >
Select ON/ OFF.
If you set SHUTTER in the AE MODE, you can control image
brightness by adjusting shutter speed.
If you set IRIS in the AE MODE, you can set the IRIS level
from 00 to 17 .
If you set MANUAL, IRIS and SHUTTER in the AE MODE, you can
set the GAIN for brighter image from 0~30dB. (Changable by 2dB)
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
AUTO EXPO.MENU
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
- SLOW SHUTTER
- SHUTTER SPEED
- IRIS LEVEL
- GAIN LEVEL
NTSC : X512, X128, X64, X32, X16, X8, 1/15, 1/30, 1/60, 1/90, 1/100,
1/180, 1/250, 1/500, 1/1000, 1/1500, 1/2000, 1/5000, 1/10000,
1/20000, 1/50000, 1/100000
PAL : X512, X128, X64, X32, X16, X8, X4, 1/25, 1/50, 1/80, 1/120,
1/150, 1/250, 1/500, 1/1000, 1/1500, 1/2000, 1/5000, 1/10000,
1/20000, 1/50000, 1/100000
AE EXPO.MENU
AE MODE : IRIS
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : 07
GAIN LEVEL : 28db
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
AGC MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
EXPO. MODE >
AE EXPO.MENU
AE MODE : AUTO
SHUTTER SPD : AUTO
SLOWSHUTTER : OFF
IRIS LEVEL : AUTO
GAIN LEVEL : AUTO
AGC MODE : ON
EXPO. MODE : ON
EXPO. LEVEL : 0dB
BACK
< NEAR / RIGHT
▶
EXPO. LEVEL >
Select ON/ OFF in AGC MODE.
Select ON/OFF
If you set ON in the EXPO MODE, you can control this level.
( "0" is standard (±10.5 selectable), changed by ± 1.5dB)
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
WB SET >
4) WHITE BALANCE
Set the white balance of camera.
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
White balance setting is a function revising color temperature to
resolve the problem that screen’s colors change by the color
temperature’s difference according to time.
- AGC MODE
- EXPO. MODE
- EXPO.LEVEL

On Screen Display Menu On Screen Display Menu
31 MIN PTZ CAMERA 30 MIN PTZ CAMERA
WHITE BALANCE MENU
WB MODE : ATW
RED GAIN : xxx
BLUE GAIN: xxx
BACK
< NEAR / RIGHT
▶
WB MODE SEL >
WHITE BALANCE MENU
WB MODE : MANUAL
RED GAIN : 208
BLUE GAIN: 162
BACK
< NEAR / RIGHT
▶
R GAIN SEL >
WB MODE: Set the color depend on white balance.
Select AUTO, INDOOR, OUTDOOR, ONEPUSHWB,
ATW or MANUAL.
RED GAIN: Adjust red color level from 0~255.
(Standard level is 025)
BLUE GAIN: Adjust blue color level from 0~255.
(Standard level is 025)
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAMERA RESET
▶
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
ICR SET >
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :11
BACK
< NEAR / RIGHT
▶
ICR MODE >
5) ICR MODE
DAY / NIGHT : Select from COLOR, BW or AUTO modes.
COLOR : Color mode.
B/W : BW mode.
AUTO : The camera automatically detects lighting conditions and selects the mode accordingly.
ICR MENU
ICR MODE : AUTO
ICR THRESHOLD :11
BACK
< NEAR / RIGHT
▶
DAY LEVEL >
Set the ICR THRESHOLD from 00 to 28 .
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
- WB MODE
- RED/BLUE GAIN
- ICR THRESHOLD
MAIN MENU
< NEAR / RIGHT
▶
SPECIAL SET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
CAM RESET
▶
SPECIAL ▶
SAVE BACK EXIT
6) SPECIAL
In the Special menu, it’s available to set SUB SP MODE,
APERTUREGAIN, FLICKERLESS, BACK LIGHT, LINE LOCK,
V PHASE, DNR LEVEL and WDR.
SUB SP MODE : In the special menu, it’s available
to set special function of the camera
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
ON/OFF>
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
STABILIZER: Select ON or OFF.
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
SUB MENU >
SUB SP MODE ▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : OFF
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
MODE>
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
HLC MODE : Select ON or OFF.
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
- SUB SP MODE
- STABILIZER
- HLC MODE

32 MIN PTZ CAMERA 33 MIN PTZ CAMERA
On Screen Display Menu On Screen Display Menu
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
LEVEL>
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
HLC CLIP LEVEL : Select HLC function ON and set the HLC
CLIP LEVEL.(0~06)
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
LEVEL>
STABILIZER : OFF
HLC MODE : OFF
HLC CLIPLEV : XX
HLC LEVEL : XX
HLC LEVEL : Set the HLC LEVEL.(0~02)
Set the APERTUREGAIN value.(0~15)
Select ON/OFF in the FLICKERLESS function.
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
APERTURE >
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
FLICKERLESS >
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
- APERTUREGAIN
- FLICKERLESS
- HLC CLIP LEVEL
- HLC LEVEL
Select ON/OFF in the BACK LIGHT function.
Select ON/OFF in the LINE LOCK function.
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
BACK LIGHT >
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Set the DNR LEVEL from AUTO, OFF and 1 ~ 10.
SPECIAL MENU
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
BACK
< NEAR / RIGHT
▶
DNR LEVEL >
Select : or Set ON :
Set OFF :
NEAR
NEAR
Select : or Set ON :
Set OFF :
NEAR
NEAR
- BACK LIGHT
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
BACK LIGHT >
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Select : or Set ON :
Set OFF :
NEAR
NEAR
- LINE LOCK
If you set ON in the LINE LOCK menu, you can set
the V PHASE.
SPECIAL MENU
BACK
< NEAR / RIGHT
▶
BACK LIGHT >
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
Select : or Set ON :
Set OFF :
NEAR
NEAR
- V PHASE
- DNR LEVEL

35 MIN PTZ CAMERA 34 MIN PTZ CAMERA
On Screen Display Menu On Screen Display Menu
Make initialize the setting value which is set in CAMERA MENU.
7) CAMERA RESET
Set the WDR MODE from OFF, LEV1 ~LEV7.
SPECIAL MENU
SUB SP MODE
▶
APERTUREGAIN : 07
FLICKERLESS : OFF
BACK LIGHT : OFF
LINE LOCK : OFF
V PHASE : 000
DNR LEVEL : AUTO
WDR MODE : LEV 7
BACK
< NEAR / RIGHT
▶
WDR MODE >
CAMERA MENU
ZOOM MODE
FOCUS MODE
AE MODE
WB MODE
ICR MODE
SPECIAL
CAM RESET
▶
▶
▶
▶
▶
▶
▶
SAVE BACK EXIT
< NEAR / RIGHT
▶
RESET >
Select : or Set ON :
Set OFF :
NEAR
NEAR
Move : Select :
NEAR
- WDR MODE
<YES> NO
5 Clear Menu
MAIN MENU
< NEAR / RIGHT
▶
CLEAR >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR ▶
PTZ RESET
▶
EXIT
CLEAR MENU
< SEL
▶
NEAR LEFT /RIGHT>
PRESET ▶YES NO
TOUR
▶
SCAN
▶
PATTERN
▶
AREA
▶
PRIVACY
▶
ALARM
▶
▶
PRESET CLEAR:
select : or Set ON :
Set OFF :
NEAR
NEAR
6 PTZ Reset
MAIN MENU
< NEAR / RIGHT
▶
RESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET ▶
EXIT
It is a reset function.
Clears the PTZ position and function value.

36 MIN PTZ CAMERA 37 MIN PTZ CAMERA
DIMENSIONS (mm) SPECIFICATIONS
Ø57.00
Ø
33.60
151.30
123.50
92.00
108.45
27.80
Auto / Zoom-Trig / Manual
0.1 / 1.0 / 1.3 / 2.0 / 6.0 m
Off / Max 2x~32x
Auto / Shutter PRI / Manual / IRIS PRI
Off / On (Auo Max 30dB)
NTSC : 1/60 ~ 1/100,000 sec PAL : 1/50 ~ 1/100,000 sec
Off / Max 2x~512x
Off / On
1 ~15 steps
Off / WDR / BLC
Auto / Sens-in / Ext / Day / Night
ATW / One-Push / Indoor / Outdoor / Manual / Auto
Off / Manual / Auto
Off / 1~7 steps
Off / H / V / H+V
1 ~ 16 steps
Off / Negative / B&W
Off / On
Privacy / MD / OD
Max. 4 Programmable zones
Sync / Phase / Comm
INT / LL
0 ~ 255 steps
Disp Sel / Init Sel / Set Title / Set Init Msg / Language
ID / Title / Zoom Ratio
ID / Baud Rate / Protocol / Version / Init Msg
PELCO-D, PELCO-P, WONWOO
RS-485
DC12V(±10%), 1.5A
0ºC ~ +50ºC (Indoor )
20% ~ 75% RH
CE, FCC
Image Sensor
Total Pixels
Scanning system
Scanning Frequency
Sync. System
Resolution
Min. illumination
Video Output
S/N Ratio
1/4" SONY Super HAD II(Double Scan) CCD
NTSC : 1028(H) × 508(V) PAL : 1028(H) x 596(V)
Interlace
NTSC : 15.734KHz(H), 59.94Hz(V) PAL : 15.625KHz(H), 50Hz(V)
Internal
700 TV lines (COLOR)
800 TV lines (BW)
Color : 0.5 lux , BW : 0.2 lux
Color DSS : 0.001 lux , BW DSS : 0.0004 lux
1.0 Vp-p (75 ohm, composite)
More than 50dB (AGC off)
Lens type
Zoom Ratio
Focal Length
Aperture Ratio
12x Day & Night Zoom Lens
Optical x12, Digital x32 Zoom
f = 3.8 mm ~ 45.6 mm
F1.6 (wide) ~ F2.7 (tele)
Focus
Focus Distance
E. Zoom
Exposure
Gain Control
Shutter Speed
Digital Shutter Speed
Flickerless
Brightness
WDR / BLC
Day&Night
White Balance
Image DNR
HR
Mirror
Sharpness
Effect
Freeze
Intelligent
Privacy Mask
Special
Sync Mode
Phase
Display
Disp Sel(Off / On)
Init Sel(Off / On)
Protocols
Communication
Power Consumption
Operating Temperature
Operating Humidity
Certification

38 MIN PTZ CAMERA 39 MIN PTZ CAMERA
Memo
FUNCTION 'D' 'P' WONWOO
PROTOCOL
GOTO PRESET
SET PRESET
GOTO TOUR
SET TOUR
GOTO SCAN
SET SCAN
GOTO PATTERN
SET PATTERN
FLIP
AUTO SCAN
START MENU
1~63 PRESET
1~63 SET PRESET
71~78 PRESET
71~78 SET PRESET
81~84 PRESET
81~84 SET PRESET
91~94 PRESET
91~94 SET PRESET
90 PRESET
99 PRESET
95 SET PRESET
1~63 PRESET
1~63 SET PRESET
71~78 PRESET
71~78 SET PRESET
81~84 PRESET
81~84 SET PRESET
91~94 PRESET
91~94 SET PRESET
90 PRESET
99 PRESET
95 SET PRESET
1~63 PRESET
1~63 SET PRESET
71~78 PRESET
71~78 SET PRESET
81~84 PRESET
81~84 SET PRESET
91~94 PRESET
91~94 SET PRESET
90 PRESET
99 PRESET
95 SET PRESET
QUICK COMMAND