Wonwoo HDSC-S202M Installation instructions

Full HD Mega-pixel Speed Dome Camera
P/N : 388065420
PRINTED IN KOREA
Distributed by
INSTALLATION / OPERATING MANUAL
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use
Wall In-Ceiling Ceiling

02
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
03
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
1. 1 Important Safety Instruction
• Read these instructions.
• Pay attention on all the warnings.
• Follow all instructions.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not dissemble or insert foreign objects.
• Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.
(Including amplifiers) that produce heat.
• Do not aim the camera at the sun or any other strong light source.
• Do not install the camera in intermittent lighting environments.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• Installation should be done only by qualified personnel and conform to all local codes.
• Installation should be done in a place strong enough to hold it.
• Use only installation methods and materials capable of supporting four times the maximum specified load.
• It is designed for indoor use only and it must not be installed where exposed to rain and moisture
without additional outdoor housing and bracket.
• To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
• These instructions are for use by qualified service personnel only. To reduce the risk of electric shock
do not perform any servicing other that contained in the operating instructions unless you are qualified
to do so.
• Only use replacement parts recommended by manufacturer. ad these instructions.
1. PRECAUTIONS
TABLE OF CONTENTS
3p.
4p.
4p.
5p.
6p.
7p.
8p.
10p.
11p.
11p.
12p.
12p.
13p.
13p.
15p.
32p.
35p.
58p.
58p.
59p.
60p.
62p.
62p.
63p.
63p.
64p.
1. PRECAUTIONS
1. 1 Important Safety Instruction ...................................................................................
2. GETTING STARTED
2. 1 Descriptions ..........................................................................................................
2. 2 Unpacking ..............................................................................................................
2. 3 EWSJ Series Selection Flow ...................................................................................
2. 4 EWSJ Series (Outdoor Speed PTZ Dome Camera ) Module .....................................
2. 5 EWSJ Series Accessories Selection (Sold Separately) ............................................
2. 6 DIP Switch Setting .................................................................................................
2. 7 Cable Connection ...................................................................................................
3. INSTALLATION (Indoor / Wall / Ceiling)
3. 1 Before Installation ..................................................................................................
3. 2 Indoor (In-Ceiling) ..................................................................................................
3. 3 Wall Mounting ........................................................................................................
3. 4 Ceiling Mounting ....................................................................................................
4. ON-SCREEN DISPLAY PROGRAM MENU
4. 1 Powering ON ..........................................................................................................
4. 2 Establishing Camera Control ...................................................................................
4. 3 Motion Setting........................................................................................................
4. 4 Dome Setting ........................................................................................................
4. 5 Camera Setting......................................................................................................
4. 6 Clear Setting ..........................................................................................................
4. 7 PTZ Reset .............................................................................................................
5. SPECIFICATION
5. 1 Mechanism Specification .......................................................................................
5. 2 Camera Specification..............................................................................................
6. DIMENSION
6. 1 EWSJ Series .........................................................................................................
6. 2 Wall and Ceiling Bracket (WB-300 / CPA-301) ........................................................
6. 3 PMB-600(Parapet Mount Bracket) .........................................................................
6. 4 CMA-100(Corner Mount / PMA-100(Pole Mount) ...................................................
7. CONFIGURATION
7. 1 Connecting to WTX-1200A with DVR .....................................................................

04
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
05
EWSJ Series Outdoor Speed PTZ Dome Camera System Use's Guide
2. 3 EWSJ Series Selection Flow2. 1 Descriptions
The Dome Supremacy EWSJ series are an outdoor speed PTZ dome system designed for IP66 applications,
especially, whether it is raining, snowing or sunny day, this EWSJ series delivers superior performance.
The EWSJ series is one unit of housing with pole, corner, wall or recessed ceiling mounts. It includes a high
resolution color camera; video output capability through coaxial cable; pan/tilt control using Pelco D or P
protocol with on-screen programming.
2. 2 Unpacking
The following parts are supplied with the EWSJ series outdoor speed PTZ dome system.
1. Dome drive
2. Dome body (housing)
3. Dome cover (bubble with trim ring)
4. Wall-mount bracket or Ceiling-mount bracket (one of two)
5. Interface cable with two wired wiper on one end and BNC female on the other end(In-ceiling only)
6. User’s Guide
7. Self-tapping screws
2. GETTING STARTED
2. 3. 1 Indoor
2. 3. 2 Outdoor
Outdoor Corner & Pole Mount EWSJ outdoor type and WB-300 and
ISB-100 and CMA-100 or PMA-100
Model Select Mount Type
Model Select Mount Type
Indoor Wall mount EWSJ outdoor type and
WB-300 and ISB-100
EWSJ outdoor type and
CPA-301(300mm) or
CPA-351(500mm)
Outdoor Parapet mount EWSJ Outdoor type
and PMB-600
Model Select Mount Type
Model Select Mount Type
Indoor ceiling mount
Model Select
In-ceiling mount EWSJ-FC
Mount Type
<Figure 1. package Components>
Dome Drive
Bracket (Wall or Ceiling) Cable & Wire(In-Ceiling only) User’s Guide Screws
Dome Body (Housing) Dome Cover Connectors

06
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
07
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
2. 5 EWSJ Series Accessories Selection (Sold Separately)2. 4 EWSJ Series
2.4. 1 EWSJ Series Models
EWSJ-M202:
1/3 " Type Exmor CMOS Sensor optical 20×with WDR
1/3" Panasonic CMOS Sensor optical 20×with WDR
IMPORTANT> When placing order, please make sure of which the below optional selection for the default
camera package is proper for your application.
- Optional 1: Smoke dome cover / Clear dome cover
- Optional 2: Including Wall-mount bracket or including Ceiling-mount bracket
IMPORTANT> Smoke dome cover let others be unaware of where the camerae is shooting.
The camera performance is likely to be the same using either smoke or transparent clear
cover orslightly darker with smoke cover. If you don't want others know where you are
shooting, then choose the smoke cover.
WB-300
- In case the camera contains
Wall-mount bracket as standard
- Aluminum body
- Unit: 1Kg
- Cool gray color
WPA-301
CPA-301 (300mm)
CPA-351 (500mm)
ITEM Model Name Image Description
PMB-600
- Stainless steel(SUS) body
- Unit : 5.2Kg
- Silver color
- Maximum load : 20Kg
- Dimensions : 890x650 (Arm)
- 250 x 350 (Mount plate)
CMA-100
PMA-100
ISB-100
- Steel body
- Unit : 0.4Kg
- Cool gray color
- In case the camera contains
Wall-mount bracket as standard
- Steel body (CPA-301: 300mm)
- Unit : 1.6Kg(CPA-301)
- Cool gray color
- Steel body
- Unit : 1.3Kg
- Cool gray color
- Steel body
- Unit : 0.7Kg
- Cool gray color
- Aluminum body
- Unit : 5Kg
- Silver color
- In case the camera contains
Wall-mount bracket as standard
- Aluminum body
- Unit: 3.1Kg
- Cool gray color
EWSJ-FC
In-ceiling mount
housing
Wall Bracke
Wall Plate
Pipe Adaptor
Ceiling Plate
Pipe Adaptor
Parapet mount
bracket
Corner Mounting
Adaptor
Pole mounting
Adaptor
Installation Box

08
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
09
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
(SW201, SW202, SW203)
(SW204, SW205, SW206)
2. 6. 4 Set the termination On/Off
(SW401)
2. 6 DIP Switch Setting
2. 6. 1 Dip Switch Setting
Before start up the dome camera, set the protocol and camera address and termination set with
dip-switches and click-switches as shown in the below diagram.
Setting Switch
(SW204, SW205, SW206)
Address Switch
(SW201, SW202, SW203)
The device which is connected at the end of the line must have the cable communication
terminated. Without proper termination, there is potential for control signal errors.EWSJ series
have the cable communication terminated by setting the appropriate dip switch as below.
1: On 2: On ' Terminated
2: Off 3: Off ' Not terminated
2. 6. 2 Set the camera address (ID)
2. 6. 3 Set the details fo the dome
S201: 100-digit number of address (ID)
S202 : 10-digit number of address (ID)
S203 : 1-digit number of address (ID)
Ex) If SW203=8, SW202=2, SW201=1,
the ID number is 128
S204 #1~#3 : Protocol setup
S204 #4, S205 #1,2 : Communication speed setup
S205 #3, #4 : Camera setup
S206 #1, #2 : Digital signal setup
S206 #3 : Communication setup
S206 #4 : NTSC, PAL setup
* See 8page.
SW204
ON
1234
SW205
ON
1234
SW206
ON
1234
SW206 RSMODE
3
OFF
ON RS-485
RS-422
SW204
PROTOCOR
1
PELCO-P
WONWOO
EZ
23
OFF OFF OFF
OFFOFF
OFF
OFF
ON
ON ON
OFF
ON
PELCO-D
ADON
ON
ON
ON ON ON
ON
ON
OFF
OFF
OFF
OFF
NC
G
NC
SW205 BAUDRATE
(BPS)
4
9600
19200
4800
2400
1
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON ON
OFF
ON
ON
ON
ON
OFF OFF
OFF
OFF
38400
57600
NC
ON
ON ON ON NC
SW205 CAMTYPE
3
NC
OFF
OFF
ON
ON
SW205
4
OFF
OFF
ON
ON
NC
EH-6300
MM-202
SW206
1
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
2OUTPUT
FORMAT 4VIDEO MODE
NTSC
PAL
OFF
ON
1920 x 1080 p 30
1920 x 1080 i 60
1280 x 720 p 60
1920 x 1080 i 59
1920 x 1080 p 25
1920 x 1080 i 50
1280 x 720 p 50

10
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
11
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
2. 7 Cable connection
3.Installtion (Indoor / Wall / Ceiling)
3. 2 Indoor (In-Ceiling)
3. 1 Before Installation
①②③④
- The following steps of installation and connection work should be done by qualified service personnel
or system installers and should conform to all local codes.
- Be sure to switch the camera off before installation is completed.
- Do not install the camera near the air outlet of an air conditioner.
- Before installation, set the dome system with Dip switch on the back side of the mechanism part, and
assemble the mechanism and housing according to the below instruction
The 2 clamp wires were used to fix mechanism to prevent
any damages in shipping.
When this camera is being installed, The clamp wires have to be
Removed from PTZ SET.
① Unpack the dome package and take out the dome drive, dome body (housing), dome cover
(bubble with trim ring) and other components. Insert the dome drive to the dome body and
connect the cables as shown in the above diagram.
② Assemble the dome cover to the dome body by pressing the cover gently downward to the
dome body with two hands on the side of the cover. Do not press the cover with strong pressure.
This might cause damage to the dome body.Screw the dome cover and body together.
③ Need for additional in-ceiling mount housing, EWSJ-FC. Refer to the page of 2.3 Products sold
separately for the detail. Make a hole in the ceiling to install the camera and prepare for the wire
with connector.For easy installation, screw the three safety screws slightly.
For the safety reason, turn off the main power during the installation.
Connect the wire to the in-ceiling mount housing assembled dome system.
Put the dome system into the ceiling hole.
④ Fasten the safety wire to the ceiling
Do not press the dome cover with too strong pressure while putting the dome system into
the ceiling hole. It can cause serious damage onto the surface of the dome cover bubble
2.7.1 Power input
Connect AC24V 3A adaptor
2.7.2 Communication terminal
In case of RS-485, connect external D+ and D- to the Rx+ and Rx- of the dome.
In case of RS-422, connect external 4 data lines to the Rx+/Rx-/Tx+/Tx- of the
dome.
2.7.3 HD-SDI output BNC
HD-SDI video output BNC
2.7.4 CVBS output
Analog video output
2.7.5 Connect ethernet (optional)
Network connecting terminal
2.7.6 ALARM/AUX output
RX+ RX- TX+ TX-
SENSOR/AUDIO
CVBS
AC24V G
HD-SDI
ETHERNET
ALARM / RELAY
RY1COM
RY1NO
RY1NC
ALM4 ALM3 ALM2 ALM1
RY2COM
RY2NO
RY2NC
ALM8 ALM7 ALM6 ALM5
① Power input⑤Connect Ethernet
③ HD-SDI output BNC
② Communication terminal
④ CVBS output
⑥ ALARM, AUX output

12
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
13
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
4. 1 Powering On
When turning EWSJ series camera power on, there is a ten (10) second pause before the camera starts
its homing phase. During the homing phase the camera pans left and right and tilts up and down. It also
adjusts the lens focus.
4. 2 Establishing Camera Control
The most common way to interface with the camera is using a keyboard and on-screen display (OSD)
menu. This method is the most common and is covered in this manual.
4. 2. 1 Basic Keyboard Operation
The following tables summarize the basic operations for a standard keyboard and the functions available
to control EWSJ series.
Table 1. 1 Typical Keyboard Functions
Table 2. 1 Typical Keyboard Controls for EWSJ series speed PTZ dome camera system
4. ON-SCREEN DISPLAY PROGRAM MENU
Typical Keyboard Features Usage
Function Keys
Number Keys
Camera Key
Enter Key
Focus Key (Or Near Key)
Iris Key
Key LEDs
LCD
Joystick
Selects a specific control setting
Inputs a number from 0 to 9.
Selects a camera number
Inputs a selection
Sets the lens focus or make a menu selection in OSD menu.
Sets the lens iris setting or makes a menu selection in OSD mode.
Indicates an active key
Displays the current status
Controls a pan/tilt/zoom (PTZ) EWSJ series
Dome Operation How to Control
To Pan Side to Side
To Tilt Up and Down
To Zoom In
To Zoom Out
Move the joystick left or right.
Move the joystick forward and back.
Twist the joystick clockwise.
Twist the joystick counterclockwise.
EWSJ series is programmed through the on-screen display (OSD) menus.
To access the OSD menus, you must open the main Setup Menu.
①②③④
①②③④
3. 3 Wall Mounting
① Insert the dome drive to the dome body and connect the cables as shown in the above diagram.
② Assemble the dome cover to the dome body by pressing the cover gently downward to the
dome body with two hands on the side of the cover. Do not press the cover with strong pressure.
This might cause damage to the dome body.Screw the dome cover and body together.
③ Install the bracket on to the wall to install the camera and prepare for the wire with connector.
For easy installation, screw the three safety screws slightly.For the safety reason, turn off the
main power during the installation. Connect the cable with the assembled dome system.
④ Put the dome system into the bracket. Fasten the 3 installation screws as shown in the above
diagram.
3. 4 Ceiling Mounting
① Insert the dome drive to the dome body and connect the cables as shown in the above diagram.
② Assemble the dome cover to the dome body by pressing the cover gently downward to the
dome body with two hands on the side of the cover. Do not press the cover with strong pressure.
This might cause damage to the dome body.Screw the dome cover and body together.
③ Make a hole in the ceiling to install the camera and prepare for the wire with connector.
For easy installation, screw the three safety screws slightly.For the safety reason, turn off the
main power during the installation. Connect the cable with the assembled dome system.
④ Put the dome system into the bracket.
Fasten the 3 installation screws as shown in the above diagram.

14
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
15
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
4. 2. 3 Setup Program OSD Menu From Keyborad.
The main Setup Menu provides access to all programmable EWSJ series settings.
4. 2. 2 Keyboard Commands
- Keyboard control commands are composed of a sequence of two (2) inputs with the following
convention: 1) a Command number key(s) + 2) a Function key.
- Command numbers range from 1 to 999.
- Refer to the keyboard manual for the key naming conventions in detail.
4. 2. 4 Go into the camera setup 0SD Menu
Press key “1” and keep pressing the “MENU” key for approximately 3 seconds, or press key “95” and
press “Preset” key to go into the set-up menu. Setup menus are shown in the diagram below. You can
adapt the camera to your requirements by setting up the respective items in these menus.
4. 3 Motion Setting
The initialize screen is shown up to check address, version,
protocol and video when the power on.
MAIN MENU
< NEAR / RIGHT →PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
The preset function is that the camera memorizes
positions of the pan/tilt and zoom. This function is
a representative function of the speed dome which
can find memorized preset positions just by selecting
the preset No. A Maximum of 255 Preset positions
are toured in
order.
4. 3. 1 Preset
Preset Quick Operating Guide
Set Preset : 1~255 + 3sec.
Go to Preset : 1~255 +
PRESET
PRESET
PRESET MENU
< NEAR / RIGHT →PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX . X, XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET SELECT 1
(1) Select the Preset number
P01 : Defined Preset number / 01 : Undefined Preset number
Move : Select : NEAR
MOTION MENU
< NEAR / RIGHT →PRESET >
PRESET
▶
TOUR
▶
SCAN
▶
PATTERN
▶
ALARM
▶
AREA
▶
PRIVACY
▶
BACK EXIT
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
▶
NEAR /MOVE & JOYSTICK>
INITIALIZE
PTZID
FIRMWARE
V-FORMAT
CVBS
PROTOCOL
BUADRATE
CAMERA
>>PAN OFFSET. . . . . PASS
>>TILT OFFSET. . . . . PASS
NORMAL SETTING . . . . . . WAIT
: 001
: X.XX
: 1080p30
: NTSC
: PELCO D V1.0
: 2400 ,N.1
: FCB EH

16
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
17
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
PRESET MENU
< NEAR / RIGHT
▶
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX . X, XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT
▶
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX .X , XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT
▶
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : 000. 0 ,000. 0
FOCUS : AUTO
SAVE CLR BACK EXIT
(4) Select the focus mode for Preset
PRESET POSITION
(3) Define the Preset position
① Select the Position menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
PRESET LABEL EDIT ( 01 )
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : PRESET 01
(2) Set the Preset Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Preset.
After the label is set, push the NEAR button to exit.
On focus menu, there are 4 modes : Auto, Manual,
On Shot. It allows detailed settings for the preset.
① Select the Focus menu
or
NEAR
② Move and set the Focus Menu
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
POSITION : 000. 0 , 000. 0
<EXIT FOCUS NEAR >
PRESET MENU
< NEAR / RIGHT
▶
PRESET NO >
PRESET NO : 01 DEFINE
LABEL :
POSITION : 000. 0 ,000. 0
FOCUS : AUTO
SAVE CLR BACK EXIT
EXTEND SET ▶
(5) “Save” above setting Pattern data to the memory.
(6) “CLR” means above setting Pattern data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU.

18
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
19
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
MAIN MENU
< NEAR / RIGHT →PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
MOTION MENU
< NEAR / RIGHT
▶
TOUR >
PRESET
▶
TOUR ▶
SCAN
▶
PATTERN
▶
ALARM
▶
AREA
▶
PRIVACY
▶
BACK EXIT
TOUR MENU
< NEAR / RIGHT
▶
TOUR NO >
TOUR NO : 01 UNDEFINE
LABEL :
TOUR EDIT :
SAVE CLR BACK EXIT
TOUR SELECT
< SEL →NEAR / MOVE
▶
JOYSTICK >
01 02 03 04 05 06
07 08
(1) Select the Tour number
T01 : Defined Tour number / 01 : Undefined Tour number
Move : Select : NEAR
The Tour function consists of several presets run by turn. It is also adjusts the moving speed
(1~63 step) and dwell time (1~99secs). Maximum of 8 Tour functions are toured in order.
4. 3. 2 Tour
Tour Quick Operating Guide
Programming : 71~78 + 3sec.
Operating : 71~78 +
TOUR
TOUR
( 1 Tour can be set for 15 presets. )
※
TOUR MENU
< NEAR / RIGHT →TOUR NO >
TOUR NO : 01 DEFINE
LABEL : TOUR 01
TOUR EDIT :
SAVE CLR BACK EXIT
(3) Define the Preset position
① Move to the set-up window
or
NEAR
② Move and set the position ③ Set & Back
NEAR
TOUR EDIT (01)
NO PRESET SPEED DWELL
01 ◀01 63 01
02 ◁ 02 63 01
03 ◁ XX XX XX
04 ◁ XX XX XX
05 ◁ XX XX XX
06 ◁ XX XX XX
07 ◁ XX XX XX
08 ◁ XX XX XX
< SEL & NEAR PRESET & LEFT >
(2) Set the Tour Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Tour.
After the label is set, push the NEAR button to exit.
PRESET SELECT 1
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
▶
NEAR /MOVE & JOYSTICK>
TOUR LABEL EDIT ( 01 )
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : TOUR 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
TOUR MENU
< NEAR / RIGHT
▶
TOUR NO >
TOUR NO : 01 DEFINE
LABEL :
TOUR EDIT :
SAVE CLR BACK EXIT
TOUR MENU
< NEAR / RIGHT →DATA SAVE >
TOUR NO : 01 DEFINE
LABEL : TOUR 01
TOUR EDIT :
SAVE CLR BACK EXIT
(4) “Save” above setting Pattern data to the memory.
(5) “CLR” means above setting Pattern data will not be
saved and be cleared.
(6) “BACK” means it goes back to the previous
menu :Motion.
(7) “EXIT” means it goes out of MENU.

20
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
21
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
SCAN SELECT
< SEL
▶
NEAR / MOVE
&
JOYSTICK >
01 02 03 04 05 06
07 08
SCAN MENU
< NEAR / RIGHT
▶
SCAN NO >
SCAN NO : 01 UNDEFINE
LABEL :
START POS : XXX . X, XXX . X
END POS : XXX . X, ---
SPEED : XX
DWELL : XX
FOCUS : NONE
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
▶
SCAN NO >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : XXX . X, XXX . X
END POS : XXX . X, ---
SPEED : XX
DWELL : XX
FOCUS : NONE
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
▶
START POS >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
▶
END POS >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
(1) Select the Scan number
S01 : Defined Scan number / 01 : Undefined Scan number
Move : Select : NEAR
The Scan function means that the camera keeps panning between two programmed pan positions.
It is also adjusts the moving speed(1~63 step). Maximum 8 Scan functions are toured in order.
4. 3. 3 Scan
Scan Quick Operating Guide
Programming : 81~88 + 3sec.
Operating : 81~88 +
SCAN
SCAN
STRAT POSITION
< EXIT →FOCUS NEAR >
POSITION : 000.0, 000.0
(3) Define the Start pan position
① Select Start Pos menu
or
NEAR
② Move and set the position ③ Go back
NEAR
(2) Set the Scan Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
(4) Define the End pan position
① Select End Pos menu
or
NEAR
② Move and set the position ③ Go back
NEAR
POSITION : 000.0, 000.0
END POSITION
< EXIT →FOCUS NEAR >
It’s available to set the desired label, displayed on the executing screen of Scan.
After the label is set, push NEAR button to go out.
MAIN MENU
< NEAR / RIGHT
▶
PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
MOTION MENU
< NEAR / RIGHT
▶
TOUR >
PRESET
▶
TOUR
▶
SCAN ▶
PATTERN
▶
ALARM
▶
AREA
▶
PRIVACY
▶
BACK EXIT
SCAN LABEL EDIT ( 01 )
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : SCAN 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >

22
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
23
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
PATTERN MENU
< NEAR / RIGHT
▶
PATTERN NO >
PATTERN NO : 01 UNDEFINE
LABEL :
RECORD :
PLAY :
SAVE CLR BACK EXIT
PATTERN SELECT
< SEL
▶
NEAR / MOVE & JOYSTICK >
01 02 03 04
(1) Select the Pattern number
PAT01 : Defined Pattern number / 01 : Undefined Pattern number
Move : Select : NEAR
The Pattern function memorizes User’s random moving path and zoom ratio. Total recording time
limit is 90secs and maximum 4 Pattern functions are toured in order.
4. 3. 4 Pattern
Tour Quick Operating Guide
Programming : 91~94 + 3sec.
Operating : 91~94 +
PATTERN
PATTERN
(8) Save above Scan data setting to the memory.
(9) “CLR” means above setting Scan data will not be
saved and be cleared.
(10) “BACK” means it goes back to the previous
menu :Motion.
(11) “EXIT” means it goes out to MENU
(7) Set the Focus
(5) Set the Scan speed
Increase : or
Decrease : or
TELE
JOYSTICK
WIDE
JOYSTICK
SCAN MENU
< NEAR / RIGHT
▶
MOVE SPEED >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
▶
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
▶
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
▶
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
MAIN MENU
< NEAR / RIGHT
▶
PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
MOTION MENU
< NEAR / RIGHT
▶
PATTERN >
PRESET
▶
TOUR
▶
SCAN
▶
PATTERN ▶
ALARM
▶
AREA
▶
PRIVACY
▶
BACK EXIT
It adjusts the moving speed from 1~63 steps.
Focus can be set Auto or Manual.
(6) Set the Dwell Time
Increase : or
Decrease : or
TELE
JOYSTICK
WIDE
JOYSTICK
Dwell time means the time that the camera stay at
the start & end pan positions.
It’s adjustable from 1~60 seconds.

24
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
25
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
PATTERN MENU
< NEAR / RIGHT
▶
EDIT LABEL >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
▶
PLAY
▶
SAVE CLR BACK EXIT
PATTERN MENU
< NEAR / RIGHT
▶
RECORD >
PATTERN NO : 01 DEFINE
LABEL :
RECORD ▶
PLAY
▶
SAVE CLR BACK EXIT
PATTERN MENU
< NEAR / RIGHT
▶
PLAY >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
▶
<08SEC>
PLAY
▶
SAVE CLR BACK EXIT
PATTERN MENU
< NEAR / RIGHT
▶
PLAY >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
▶
<08SEC>
PLAY
▶
SAVE CLR BACK EXIT
(4) Play back the recorded Pattern data
(3) Record and Save the User’s random Pattern data
① Select the “Record” Menu
or
NEAR
② Move and record the pattern ③ Set & Back
NEAR
000.0, 000.0
EXIT
▶
NEAR 06/60
PATTERN RECORD
(2) Set the Pattern Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Pattern.
After the label set, push NEAR button to go out.
(5) “Save” above setting Pattern data to the memory.
(6) “CLR” means above setting Pattern data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU.
PATTERN LABEL EDIT ( 01 )
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : PATTERN
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >

26
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
27
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
AREA MENU
< NEAR / RIGHT
▶
AREA NO > <SEL & MEAR / MOVE & JOYSTICK>
AREA NO : 01 UNDEFINE
LABEL :
START PAN POS.: XXX . X
STOP PAN POS.: XXX . X
SAVE CLR BACK EXIT
AREA MENU
< MOVE & NEAR / JOYSTICK >
AREA NO : 01 DEFINE
LABEL :
START PAN POS.: 000 . 0
STOP PAN POS.: 000 . 0
SAVE CLR BACK EXIT
AREA MENU
< MOVE & NEAR / JOYSTICK >
AREA NO : 01 DEFINE
LABEL :
START PAN POS.: 000 . 0
STOP PAN POS.: 000 . 0
SAVE CLR BACK EXIT
AREA MENU
< NEAR / RIGHT
▶
AREA NO >
AREA NO : 01 DEFINE
LABEL :
START PAN POS.: XXX . X
STOP PAN POS.: XXX . X
SAVE CLR BACK EXIT
AREA MENU
< NEAR / RIGHT
▶
AREA >
AREA NO : 01 DEFINE
LABEL : AREA 01
START POS : 000 . 0 .
STOP POS : 000 . 0 .
SAVE CLR BACK EXIT
The Area function means that it displays the Area name between two programmed pan positions.
Maximun 16 Area functions are toured in order.
4. 3. 5 Area
MAIN MENU
< NEAR / RIGHT
▶
PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
MOTION MENU
< NEAR / RIGHT
▶
PATTERN >
PRESET
▶
TOUR
▶
SCAN
▶
PATTERN
▶
ALARM
▶
AREA ▶
PRIVACY
▶
BACK EXIT
AREA SELECT
01 02 03 04 05
06 07 08 09 10
11 12 13 14 15
16
(1) Select the Area number
AR 01 : Defined Area number / 01 : Undefined Area number
Move : Select : NEAR
(2) Set the Area Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Area.
After the label set, push NEAR button to go out.
AREA START PAN POSITION
< EXIT →FOCUS NEAR >
POSITION : 000.0
AREA STOP PAN POSITION
< EXIT →FOCUS NEAR >
POSITION : 000.0
(3) Define the Start pan position
① Select the “Start Pan Pos” menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
(4) Define the Stop pan position
① Select the “Start Pan Pos” Menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
** Only pan position is adjustable, becaue tilt position is fixed when “Start Pan Position” is set.
(5) “Save” above setting Area data to the memory.
(6) “CLR” means above setting Area data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU
AREA LABEL EDIT ( 01 )
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : AREA
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
※ Camera will move to clockwise direction only when START setting.

28
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
29
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
ALARM MENU
< NEAR / RIGHT
&
ALARM NO >
ALARM NO : 01 UNDEFINE
LABEL :
PRESET NO. : XX
SAVE CLR BACK EXIT
ALARM MENU
< NEAR / RIGHT
&
ALARM LABEL >
ALARM NO : 01 DEFINE
LABEL :
PRESET NO. : XX
SAVE CLR BACK EXIT
ALARM MENU
< NEAR / RIGHT
&
SELECT PRESET >
ALARM NO : 01 DEFINE
LABEL :
PRESET NO. : 01
SAVE CLR BACK EXIT
The Alarm function means that the camera moves to the programmed Preset position by the Alarm trigger.
Maximum 2 Alarm functions are toured in order.
4. 3. 6 Alarm
MAIN MENU
< NEAR / RIGHT
▶
PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
MOTION MENU
< NEAR / RIGHT
▶
PATTERN >
PRESET
▶
TOUR
▶
SCAN
▶
PATTERN
▶
ALARM ▶
AREA
▶
PRIVACY
▶
BACK EXIT
(1) Select the Alarm number
Alarm 01 : Defined Alarm number / 01 : Undefined Alarm number
Move : Select : NEAR
(2) Set the Alarm Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Alarm.
After the label is set, push the NEAR button to exit.
(3) Define the Preset position with Alarm trigger
① Select the “Preset No”
or
NEAR
② Move and set the position ③ Set & Back
NEAR
(4) “Save” above setting Alarm data to the memory.
(5) “CLR” means above setting Alarm data will not be
saved and be cleared.
(6) “BACK” means it goes back to the previous
menu :Motion.
(7) “EXIT” means it goes out of MENU
PRESET SELECT
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
▶
NEAR /MOVE & JOYSTICK>
ALARM LABEL EDIT ( 01 )
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : ALARM 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
ALARM MENU
< NEAR / RIGHT
&
SELECT PRESET >
ALARM NO : 01 DEFINE
LABEL :
PRESET NO. : 01
SAVE CLR BACK EXIT
ALARM SELECT
< SEL →NEAR / MOVE  JOYSTICK >
01 02
07 08
03 04 05 06

30
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
31
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
PRIVACY MENU
< NEAR / RIGHT
▶
AREA >
SAVE CLR BACK EXIT
MAIN MENU
< NEAR / RIGHT
▶
PRESET >
MOTION
▶
DOME
▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
MOTION MENU
< NEAR / RIGHT
▶
PATTERN >
PRESET
▶
TOUR
▶
SCAN
▶
PATTERN
▶
ALARM
▶
AREA
▶
PRIVACY ▶
BACK EXIT
The Privacy Zone Masking function means that it sets the blocking territories to prevent camera functions
for the privacy of personal reasons. Maximum of 8 Privacy Zone Masking functions are toured in order.
4. 3. 7 Privacy Zone Masking
PRIVACY MENU
< NEAR / RIGHT
▶
PRIVACY NO >
PRIVACY NO : 01 UNDEFINE
POSITION : XXX . X , XXX . X
SAVE CLR BACK EXIT
PRIVACY MENU
< NEAR / RIGHT
▶
PRIVACY NO >
PRIVACY NO : 01 UNDEFINE
POSITION : XXX . X , XXX . X
PRIVACY NO : 01 UNDEFINE
POSITION : XXX . X , XXX . X
SAVE CLR BACK EXIT
PRIVACY SELECT
< SEL →NEAR / MOVE
▶
JOYSTICK >
01 02 03 04 05
06 07 08
(1) Select the Privacy Zone number
Privacy 01 : Defined Alarm number / 01 : Undefined Alarm number
Move : Select : NEAR
(2) Set the Privacy Zone Position
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired position and size of the blocking territories freely.
After the Privacy Zone is set, push the NEAR button to go out.
PRIVACY POSITION
< EXIT
▶
FOCUS NEAR >
POSITION : 000. 0 , 000 .
MASK SIZE : <OPEN / CLOSE >
(3) “Save” above settings of Privacy Zone data to the memory.
(4) “CLR” means above setting of Privacy Zone data will not
be saved and be cleared.
(5) “BACK” means it goes back to the previous
menu :Motion.
(6) “EXIT” means it goes out of MENU.

32
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
33
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
PARK MENU
<NEAR / RIGHT & PARK TIME>
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
SAVE CLR BACK EXIT
PARK MENU
<NEAR / RIGHT & PARK TIME>
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
SAVE CLR BACK EXIT
PARK MENU
<NEAR / RIGHT & PARK TIME>
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
SAVE CLR BACK EXIT
(1) Set the park Time (OFF, 01~60 min)
(2) Select the function which will be back
after the above set time.
(3) Select the appointed function’s Number
NEAR
< NEAR / RIGHT
▶
DWELL >
SAVE CLR BACK EXIT
MAIN MENU
< NEAR / RIGHT
▶
PRESET >
MOTION
▶
DOME ▶
CAMERA
▶
CLEAR
▶
PTZ RESET
▶
BACK EXIT
4. 4 Dome Setting
4. 4. 2 Set the Power Up Action
When this function is ON, the camera memorizes the latest action and restores, it from sudden power
failure.
select : or Set ON : Set OFF :
NEAR
4. 4. 1 Set the Dome camera title
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired camera title.
After the label is set, push NEAR button to exit.
Pan, Tilt, Zoom motion is adjustable in the “Dome Setting” Menu.
DOME MENU
TITLE
: EH-202
AUTO FLIP : ON
TILT LIMIT : OFF
POWER UP ACTION : ON
PARK ACTION
▶
DISPLAY ON/OFF
▶
SPEED BY ZOOM : ON
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
DOME MENU
TITLE : EH-202
AUTO FLIP : ON
TILT LIMIT : OFF
POWER UP ACTION : ON
PARK ACTION
▶
DISPLAY ON/OFF
▶
SPEED BY ZOOM : ON
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
DOME MENU
TITLE : EH-202
AUTO FLIP : ON
TILT LIMIT : OFF
POWER UP ACTION : ON
PARK ACTION
▶
DISPLAY ON/OFF
▶
SPEED BY ZOOM : ON
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
4. 4. 3 PARK ACTION
or NEAR
(4) “Save” above setting data to the memory.
(5) “CLR” means above setting Pattern data will
not be saved and be cleared.
(6) “BACK” means it goes back to the previous
menu.
(7) “EXIT” means it goes out of the MENU
PARK MENU
TIME <MIN> : OFF
FUNCTION : NONE
NUMBER : XX
TITLE SET
< DELETE
▶
WIDE
< STORE
▶
TELE
BACK
▶
NEAR >
MOVE
▶
JOYSTICK >
LABEL : EH-202
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
This function enables to locate the camera to specific
position automatically if operator doesn’t operate the
controller for a while.

34
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
35
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
4. 4. 4 Display ON/OFF Set
You can select the OSD ON to shown on the screen or clear by selecting OFF in this function.
select : or Set ON : Set OFF :
NEAR NEAR
4. 4. 5 Speed by Zoom ON/OFF Set
When this function is ON, the pan/tilt speed is
inversely adjusted to the zoom ratio.
select : or Set ON :
Set OFF :
NEAR
NEAR
4. 4. 6 Auto Filp ON/OFF Set
select : or Set ON :
Set OFF :
NEAR
NEAR
4. 5 Camera Setting
CAMERA MENU
- Functions can be set-up using the Camera menu.
In this menu, user can set the zoom, focus, white balance, auto exposure...etc functions.
4. 5. 1 CAMERA MENU (EH-6300)
Decide using of digital zoom function and select zoom speed.
＊ZOOM SPD : 1 ~ 7steps, USER(standard)
＊D-ZOOM : ON / OFF
① ZOOM MODE
- ZOOM SPD
- D-ZOOM
ZOOM SPD : Select from 1sept to 7 steps,
USER (Standard speed)
Decide using of digital zoom function.
D-ZOOM: ON/ OFF
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
MAIN MENU
MOTION
DOME
CAMERA
CLEAR
PTZ RESET
EXIT
< NEAR / RIGHT ▷ MOTION >
→
→
→
→
▷
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ ZOOM MODE >
▷
▷
▷
▷
▷
▷
▷
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ ZOOM MODE >
▷
▷
▷
▷
▷
▷
▷
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : ON
BACK
▷
< NEAR / RIGHT ▷ ZOOM SPD >
ZOOM MENU
ZOOM SPD : USER
D-ZOOM : ON
BACK
▷
< NEAR / RIGHT ▷ D-ZOOM >
You can observe the moving object without reversing
of the screen, by using this AUTO FLIP function.
ON: If this function is set to ON, camera will be
automatically flipped in tilt 90°
OFF: If this function is set to OFF, tilt movement
range is 0~90°
DOME MENU
TITLE : EH-202
AUTO FLIP
TILT LIMIT
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
DISPLAY ON/OFF MENU
TITLE :
ZOOM :
PRESET :
TOUR :
AREA :
ALARM :
PATTERN :
PRIVACY :
SCAN :
POSITION :
ACTION :
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<V>
<ON
▶
TETLE MOVE
▶
JOY >
<OFF
▶
WIDE BACK
▶
NEAR>
▶
▶
: ON
: ON
: OFF
DOME MENU
TITLE : EH-202
AUTO FLIP
TILT LIMIT
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
DOME MENU
TITLE : EH-202
AUTO FLIP
TILT LIMIT
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
FACTORY SET
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
▶
▶
: ON
: ON
: OFF
DOME MENU
TITLE : EH-202
AUTO FLIP
POWER UP ACTION : ON
PARK ACTION
DISPLAY ON/OFF
SPEED BY ZOOM
FACTORY SET
TILT LIMIT
SAVE BACK EXIT
< NEAR / RIGHT
▶
TITLE SET >
▶
▶
: ON
: ON
: OFF
▶
▶
: ON
: ON
: OFF
4. 4. 7 TILT LIMIT Set
Set tilt angle from 0º to 15º
(OFF~15º)
Factory Set
Restore setting values to the factory default.
All existing setting value will be erased.

36
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
37
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
② FOCUS MODE
- FOCUS SPD
- FOCUS MODE
- NEAR LIMIT
In Focus menu, you can set up the focus speed, focus mode,
near limit, AF mode and sensitivity.
Set the speed for camera focusing.
AUTO: The camera adjusts the focus automatically while
monitoring the screen continuously in the auto mode. In the auto
focusing mode, zoom key operation is not recognized as the input
of the focus key.
Manual: In the manual mode, users can adjust the camera focus
manually.
One Push: It will be focused in about 5 seconds after zooming,
panning, and return to MANUAL mode automatically. This is for
focusing accurately after zooming.
Infinity: infinity focus is the state where a lens forms an image of
an object an infinite distance away. This corresponds to the point
of focus for parallel rays.
Infinity focus is the state where a lens forms an image of
an object an infinite
distance away. This corresponds to the point of focus for
parallel rays.
( Over Infinity~ 1.0CM)
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ ZOOM MODE >
▷
▷
▷
▷
▷
▷
▷
: USER
: AUTO
: 8CM
: NORMAL
: NORMAL
: STANDARD
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
SENSITIVITY
IRSELECTION
BACK
▷
< NEAR / RIGHT ▷ FOCUS SPD >
: USER
: AUTO
: 8CM
: NORMAL
: NORMAL
: STANDARD
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
SENSITIVITY
IRSELECTION
BACK
▷
< NEAR / RIGHT ▷ FOCUS MODE >
: USER
: AUTO
: 8CM
: NORMAL
: NORMAL
: STANDARD
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
SENSITIVITY
IRSELECTION
BACK
▷
< NEAR / RIGHT ▷ NEAR LIMIT >
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
Set the AUTO FOCUS MODE position
Set the sensitivity of focus.
- AF MODE
- SENSITIVITY
Correct the IR conversion data.
- IR SELECTION
: USER
: AUTO
: 8CM
: NORMAL
: NORMAL
: STANDARD
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
SENSITIVITY
IRSELECTION
BACK
▷
< NEAR / RIGHT ▷ AF MODE SEL >
: USER
: AUTO
: 8CM
: NORMAL
: NORMAL
: STANDARD
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
SENSITIVITY
IRSELECTION
BACK
▷
< NEAR / RIGHT ▷ AF SENS SEL >
: USER
: AUTO
: 8CM
: NORMAL
: NORMAL
: STANDARD
FOCUS MENU
FOCUS SPD
FOCUS MODE
NEAR LIMIT
AF MODE
SENSITIVITY
IRSELECTION
BACK
▷
< NEAR / RIGHT ▷ IR SEL >

38
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
39
EWSJ Series Outdoor Speed PTZ Dome Camera System User’s Guide
③ WHTE BALANCE Set the white balance of camera.
④ AUTO EXPO
- WB MODE
Adjust color leverl (RED, BLUE : 001~ 255)
Standard level : RED -> 208 BLUE->162
- RED, BLUE MODE
White balance setting is a function revising color temperature to
resolve the problem that screen’s colors change by the color
temperature’s difference arrcording to time.
RED GAIN: Adjust red color level from 0~255.
BLUE GAIN: Adjust blue color level from 0~255.
WB MODE: Set the color depend on white balacne.
WB MODE : Select AUTO, INDOOR, OUTDOOR, OUTDOOR AUTO,
ONE PUSH, SODIUM, AUTO SODIUM, ATW or MANUAL
AE setting is a function adjusting shutter speed acoording to
subject’s brightness to get standard amount of exposed light.
AE MODE: Select AUTO,MANUAL,SHUTTER, IRIS.
EXPOSURE : 10.5dB ~ -10.5dB (Standard 0dB)
SLOW SHUTTER: Select AUTO, MENUAL
SHUTTER: Set the shutter speed.
IRIS LEVEL: If you set IRIS in AE mode, you can control the level value
BRIGHT LEVEL: If you set BRIGHT in AE mode, you can control level
value (00~31)
Gain: Control the brightness
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ WB SETTING >
▷
▷
▷
▷
▷
▷
▷
: AUTO
: XXX
: XXX
WHITE BALANCE MODE
WB MODE
RED GAIN
BLUE GAIN
BACK
▷
< NEAR / RIGHT ▷WB MODE SEL >
: MANUAL
: 208
: 162
WHITE BALANCE MODE
WB MODE
RED GAIN
BLUE GAIN
BACK
▷
< NEAR / RIGHT ▷WB MODE SEL >
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
CAMERA MENU
ZOOM MODE
FOCUS MODE
WHITE BAL.
AUTO EXP.
WDR MODE
SPECIAL
CAMERA RESET
SAVE BACK EXIT
▷
< NEAR / RIGHT ▷ AE SETTING >
▷
▷
▷
▷
▷
▷
▷
- AE MODE
- SHUTTER
- EXPO MODE
- SLOW SHUTTER
Select AUTO,MANUAL,SHUTTER, IRIS or BRIGHT.
Set the exposure.
Select AUTO or MANUAL .
If you set SHUTTER in the AE MODE, you can control shutter
speed.
(1/50, 1/80, 1/120, 1/150, 1/250, 1/500, 1/1000, 1/1500,
1/2000, 1/5000, 1/10000, 1/20000, 1/50000, 1/100000)
: AUTO
: 0dB
: AUTO
: AUTO
: AUTO
: XX
: XX
: 6dB
AUTO EXPO. MENU
AE MODE
EXPOSURE
SLOW SHUTTER
SHUTTER
IRIS LEVEL
BRIGHT LEVEL
GAIN
GAIN LIMIT
BACK
▷
< NEAR / RIGHT ▷AE MODE SEL >
: SHUTTER
: 0dB
: AUTO
: 1/60
: AUTO
: XX
: XX
: 6dB
AUTO EXPO. MENU
AE MODE
EXPOSURE
SLOW SHUTTER
SHUTTER
IRIS LEVEL
BRIGHT LEVEL
GAIN
GAIN LIMIT
BACK
▷
< NEAR / RIGHT ▷AE MODE SEL >
: AUTO
: 0dB
: AUTO
: AUTO
: AUTO
: XX
: XX
: 6dB
AUTO EXPO. MENU
AE MODE
EXPOSURE
SLOW SHUTTER
SHUTTER
IRIS LEVEL
BRIGHT LEVEL
GAIN
GAIN LIMIT
BACK
▷
< NEAR / RIGHT ▷EXPO SEL >
: AUTO
: 0dB
: AUTO
: AUTO
: AUTO
: XX
: XX
: 6dB
AUTO EXPO. MENU
AE MODE
EXPOSURE
SLOW SHUTTER
SHUTTER
IRIS LEVEL
BRIGHT LEVEL
GAIN
GAIN LIMIT
BACK
▷
< NEAR / RIGHT ▷SLOWSHUTTER >
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR
select : or Set ON : Set OFF :
NEAR NEAR