WoodFast PT310A User manual

Instruction
Manual
IMPORTANT
For your safety read
instructions carefully
before assembling or
using this product.
Save this manual for
future reference.
Planer & Thicknesser
PT310A
Original Instruction
V.4-202005
/RIGINAL¬)NSTRUCTION¬-ANUAL
6ERSION¬
&EBRUARY¬
7OODWORKING¬-ACHINES¬¬!CCESSORIES
4ELEPHONE¬¬¬
&AX¬¬¬
3TARTRITE
5NIT¬"¬!DELPHI¬7AY
3TAVELEY¬¬3¬,3
%MAIL¬SALES RECORDPOWERCOUK
WWWSTARTRITECOUK
%¬%¬¬%¬¬¬
)NDUSTRIAL¬¬
"ANDSAW
)-0/24!.4
&OR¬YOUR¬SAFETY¬READ¬INSTRUCTIONS¬CAREFULLY¬BEFORE¬
ASSEMBLING¬OR¬USING¬THIS¬PRODUCT¬3AVE¬THIS¬
MANUAL¬FOR¬FUTURE¬REFERENCE
(%!,4(¬!.$¬3!&%49¬'5)$%,).%3
!LWAYS¬FOLLOW¬THE¬INSTRUCTIONS¬PROVIDED¬WITH¬THE¬MANUAL¬!LWAYS¬WEAR¬SAFETY¬GLASSES¬WHEN¬USING¬WOODWORKING¬
EQUIPMENT¬!LWAYS¬DISCONNECT¬THE¬POWER¬BEFORE¬ADJUSTING¬ANY¬EQUIPMENT¬&AILURE¬TO¬OBSERVE¬PROPER¬SAFETY¬
PROCEDURES¬AND¬GUIDELINES¬CAN¬RESULT¬IN¬SERIOUS¬INJURY
7!2.).'¬$O¬NOT¬ALLOW¬FAMILIARITY¬GAINED¬FROM¬FREQUENT¬USE¬OF¬YOUR¬MACHINE¬AND¬ACCESSORIES¬TO¬BECOME¬
COMMONPLACE¬!LWAYS¬REMEMBER¬THAT¬A¬CARELESS¬FRACTION¬OF¬A¬SECOND¬IS¬SUFlCIENT¬TO¬INmICT¬SEVERE¬INJURY !LWAYS¬WEAR¬SAFETY¬GLASSES¬WHEN¬
USING¬WOODWORKING¬EQUIPMENT
!LWAYS¬READ¬THE¬INSTRUCTIONS¬
PROVIDED¬BEFORE¬USING¬
WOODWORKING¬EQUIPMENT

Index
1 GENERAL INFORMATION
1.1 Foreword
2 MACHINE DESCRIPTION
2.1 Machine identification
2.2 Getting to know your machine
2.3 Technical specification
2.4 Recommended protective clothing
2.5 Noise emission
2.6 Prescribed use of the machine
2.7 Hazards
2.8 Safety instructions for planer/thicknesser
3 INSTALLATION
3.1 Lifting and unloading
3.2 Position of the machine
3.3 Identifying shipping boxes
3.4 Installations of loose parts
3.4.1 Fence installation
3.4.2 Switch installation
3.5 Electrical connection
3.6 Dust chute - installation
4 INSTALLATION AND ADJUSTMENT
4.1. Thicknesser table height adjustment
4.2. Infeed table height adjustment
4.3. Jointer fence adjustment
5 OPERATING PROCEDURES
5.1 ON/OFF switch
5.2 Surface planer mode
5.3 Thickness planer mode
6 MAINTENANCE
6.1 Replacing cutter knives
6.2 Drive Belt Check
7 DIAGRAMS & COMPONENTS
-2-

4
5
1
3
2
8
6
79
1. General Information
1.1 FOREWORD
This manual must be read and understood before operating the machine. This will provide a better working knowledge of the
machine, for increased safety and to obtain the best results.
2. Machine Description
2.1 MACHINE IDENTIFICATION
There is a metallic identification plate fixed to the machine, containing the manufacturer's data, year of construction, serial number.
2.2 GETTING TO KNOW YOUR MACHINE
1 Height setting of thicknesser bed
2 Jointer fence
3 Infeed table
4 Height setting of infeed table
5 On/off switch
6 Frame
7 Cutterblock
8 Cutterblock guard
9 Outfeed table
-3-

2.3 TECHNICAL SPECIFICATION
SPECIFICATION PT310A
Feed speed m/min 7
Cutterblock speed rpm 5500
Cutterblock diameter mm 70
Max thicknesser capacity mm 310x225
Max planing width mm 310
Max depth of cut thicknesser mm 3
Max depth of cut planer mm 3
Knives pcs 3
Fence tilting degree 0-45
Motor power output 220-240V/2.5kW
380-415V/2.2kW
Net Weight kg 230
2.4 RECOMMENDED PROTECTIVE CLOTHING
• Non-slip footwear is recommended.
• Do not wear loose clothing, neckties or jewellery; they can be caught in moving parts.
• Roll up long sleeves above the elbow.
• Wear protective hair covering to contain long hair.
2.5 NOISE EMISSION
The measurements of noise, in the working position and during operation, were carried out under the standard ISO 7960 Annex B and C:
Instantaneous acoustic pressure:
Sound power level(no load) <98dB(A)
Sound power level(load) <107dB(A)
Sound Pressure level(no load) <89dB(A)
Sound Pressure level(load) <98dB(A)
Constant K=4 dB measured in accordance with EN ISO 3746:1995
The figures quoted are emission levels and are not necessarily safe working levels. Whilst there is a correlation between the emission
and exposure levels, this cannot be used reliably to determine whether or not further precautions are required. Factors that influence
the actual level of exposure of the workforce include the characteristics of the work room and the other sources of noise etc. i.e.
the number of machines and other adjacent processes. Also the permissible exposure level can vary from country to country. This
information, however, will enable the user of the machine to make a better evaluation of the hazard and risk.
2.6 PRESCRIBED USE OF THE MACHINE
This machine is intended for surface planing and thickness planing of solid woods. The permissible workpiece dimensions must be
observed (see Technical Specification).
Any other use is not as specified. Unspecified use, modification of the machine or use of parts not tested and approved by the
equipment manufacturer can cause unforeseen damage.
2.7 HAZARDS
ATTENTION Planer & thicknesser still present risks that cannot be eliminated by the manufacturer. Therefore the user must be aware
that wood working machines are dangerous if not used with care and all safety precautions adhered to.
-4-

2.8 SAFETY INSTRUCTIONS FOR PLANER.THICKNESSER
A planer/thicknesser is a tool which can, due to operator carelessness, cause serious personal injury. It is therefore strongly
recommended you read and observe:
· these instructions, particularly the special safety information in the respective chapters;
· the relevant guidelines or regulations for the prevention of accidents pertaining to the use of planer/thicknessers, where applicable.
Keep all documents, supplied with the machine, for future reference.
The planer/thicknesser shall only be started and operated by persons familiar with planer/thicknessers and who are at any time aware
of the dangers associated with the operation of such tool. Persons under 18 years of age shall use this planer/thicknesser only under
the supervision of an instructor in the course of their vocational training.
The following residual risks do principally exist with planer/thicknessers and can not, even by employing safety devices, completely
eliminated:
- Hazard generated by environmental conditions:
do not operate the planer/thicknesser in rain or damp environment. Ensure sufficient lighting. Do not
operate the planer/thicknesser near inflammable liquids or gases.
- Hazard to other persons in the work area:
Keep bystanders, particularly children, out of the danger zone.
- Risk of injury by machine faults:
check the planer/thicknesser for damage before any use. Do not operate the machine with a damaged part. Replace blunt cutter
knives at once. Risk of injury by kickback if a blunt knife gets caught in the workpiece's surface.
- Risk of injury by an unstable stand of the planer/thicknesser:
when working long stock use suitable supports on both sides of the machine. Avoid adverse body positions. Ensure firm footing, and
keep your balance at all times.
- Risk of injury by foreign objects in the machine:
prior to any starting of the machine ensure that there are no objects (e.g. tools) in the machine.
- Risk of injury by workpiece kickback (workpiece is caught by the rotating cutterblock and thrown back against the
operator):
operate machine only with a fully functional anti-kickback lock. Always use sharp cutter knives. If in doubt check workpiece for
inclusion of foreign objects (e.g. nails, screws, lose knots).
- Risk of injury by touching the rotating cutterblock:
always keep your hands well clear of the cutterblock. Switch machine off and plug out if it is not used.
- Danger! Drawing-in/trapping hazard!
Take care that no parts of the body or clothing can get caught and drawn in by the rotating cutterblock (do not wear neck ties and
garments with wide sleeves; contain long hair with a hairnet).
- Risk of injury by cuts with cutterblock at standstill: Wear gloves when changing cutter knives.
- Risk of injury by inhaling wood dust: dust of certain timber species (e.g. oak, beech, ash) can cause cancer when inhaled. Use a
suitable dust collector:
- fitting the outer diameter of the suction port (100 mm)
- air volume >= 815 m3/h;
- vacuum at suction port of machine >= 740 Pa;
- air speed at suction port of machine >= 20 m/s;
- Risk of injury by inadequate personal protection: when planing, wear:
- dust respirator;
- hearing protection;
- safety goggles.
-5-

3. Installation
3.1. LIFTING AND UNLOADING
The machine can be transported by two means:
- with a forklift truck. To do so, the machine is secured on a
pallet with four hex bolts.
- by several persons. Here, the machine is carried by means of
carrying straps or two battens (A, Fig.1) placed underneath the
thicknesser bed.
CAUTION
Do not carry the machine holding it at the infeed and outfeed
tables, these are not designed to withstand the tensile load by
the machine weight.
3.2 POSITION OF THE MACHINE
CAUTION
It is prohibited to install the machine in explosive environments.
Ensure that the floor area around the machine is level, well
maintained and free from loose material e.g. chips;
1. Remove four mounting bolts from the machine base.
2. Lift machine off the pallet and set down on the floor.
3. Fix the machine to the floor. Fix the machine feet and fix on
ground by means of expansion bolts (not supplied).
3.3 IDENTIFYING SHIPPING BOXES
BEFORE ASSEMBLY
It is advisable that before unpacking to have plenty of paper
towels or cloths available to clean off the rust preservative.
A
FIG. 1
FIG. 2
FIG. 3
-6-

3.5 ELECTRICAL CONNECTION
Electrical installation should be carried out by competent, qualified personnel.
The mains connection should be made using the terminal box.
Ensure that the mains supply corresponds with that of the machine, use cables of a section suitable for the power of the motor. For a
supply tension of 400 V the minimum section recommended is 2.5 mm, including the earth wire.
For a mains supply of 230 V or a power rating greater than 15 A it will be necessary to increase the section of the connecting cables .
Connect the phase wires to the terminals R- S - T (L1 - L2 - L3) and the earth wire to the earth terminal.
On initial start-up check the direction of rotation, if it is incorrect then invert the two phase wires (for machines with 3 phase supply).
Direction of rotation of machines with single-phase supply is pre-determined during production .
On completion of the installation check that the terminal box is closed correctly and that the plug points are locked.
C
BA
3.4. INSTALLATIONS OF LOOSE PARTS
G
H
FIG. 4
FIG. 5
3.4.1 SWITCH - INSTALLATION
- Fit the switch (G, Fig.4) onto the bracket with two hex nuts (H,
Fig.7)
3.4.2 Cutterblock guard - INSTALLATION
- Take off both of the hex socket screws (A, Fig.5). Install the
cutterblock guard assembly (B, Fig.5) using two of hex socket
screws. Make sure the square washer (C, Fig. 5) stay between
the table and cutterblock guard.
PE
N
34 44 b
33 43 a
L
OL
ON
OFF
Motor
Safty switch
Yellow Green
Blue
Brown
Black
Brown
Blue
23 33 43 a
b443424
OL
ON
OFF
L1
PE
L3
L2
Motor
Safty Switch
Yellow Green
Blue
Brown
Gray
Brown
Blue
Black
PT310 Single phase PT310 Three phase
-7-

IK
J
3.6. DUST CHUTE - INSTALLATION
The dust chute complete with suction connector must be
installed for thickness planing.
CAUTION: The contact pins on the shaft of the dust chute (A,
Fig. 6) must engage properly in the limit switch. Incorrectly
installed dust chute the machine will not start.
Connect a suitable dust collector to the suction connector of the
planer/thickesser.
A
4. Adjustment
4.1. THICKNESSER TABLE HEIGHT
ADJUSTMENT
With the height setting for the thicknesser bed the planing
thickness (= thickness of the workpiece after planing) is set
when the machine is used for thickness planing.
· Per pass a maximum of 3 mm material can be removed.
· Workpieces of max. 200 mm thickness can be planed. Height
adjustment is made with a handwheel (B, Fig.7). One full turn
of the crank changes the height of the thicknesser bed (C, Fig.7)
by 4 mm.
· Clockwise turning = raises the thicknesser bed
· Counter-clockwise turning = lowers the thicknesser bed. The
set planing thickness is indicated on the scale (D, Fig.7).
4.2. INFEED TABLE HEIGHT ADJUSTMENT
With the height setting for the infeed table (E, Fig,8) the depth of
cut is set when the machine is used for surface planing.
· The scale (F, Fig.8) next to the adjusting lever (G, Fig.8)
corresponds to 1 mm chip removal.
- Per pass a maximum of 3 mm material can be removed.
4.3. JOINTER FENCE ADJUSTMENT
The jointer fence (I, Fig.9) provides lateral support for the
workpiece when surface planing.
· After loosening the lock lever (J, Fig.9) the jointer fence can be
adapted to the workpiece width.
· After loosening the lock lever (K, Fig.9) the jointer fence
extrusion can be tilted to the angle between 0°- 45°.
E
G
F
DB
C
I
FIG. 6
FIG. 7
FIG. 8
FIG. 9
-8-

5.1. ON/OFF SWITCH (Fig.10)
· To switch ON = press green switch button.
· To switch OFF = close cover or press red switch button.
· To unlock the switch cover push the pin on the stop cover.
5.2 SURFACE PLANER MODE:
Note: With surface planing, an irregular surface is planed flat (=
jointed).
- The workpiece rests on top of the infeed table.
- The workpiece is cut on the underside.
- The feed direction of the workpiece is exactly opposite than
when thickness planing.
Workpiece dimensions
- Length: use a push stick to feed workpieces shorter than 250
mm; for workpieces over 1500 mm use a second person for
support.
- Width: max. 310 mm.
- Thickness: min. 5 mm.
Note: The max. depth of cut for a single pass is 3 mm.
1. Assume proper operating position:
position yourself to one side of the infeed table.
2. Set jointer fence as required.
3. Set planing thickness.
4.Release the Belt Lever for Planer Drive Rollers, at the jointer
outfeed end of the cabinet. FIG. 13. This will transfer more
power directly to the cutterhead.
5. Place workpiece against jointer fence .
6. Adjust cutterblock cover:
- when planing narrow edges (jointing) or workpieces more than
75 mm thick:
Set cutterblock cover from the side against the workpiece (A,
Fig.12)..
5. Operating Procedures
A
ON
OFF
FIG. 10
FIG. 11
FIG. 12
FIG. 13
-9-

max. 3 mm max. 2 mm
- Planing the face of a plank or workpieces up to 75 mm
thick: lower cutterblock cover from top onto workpiece. Adjust
cutterblock cover so that the undermentioned distances are not
exceeded in any position:
rear edge (A, Fig.14) – workpiece max. 3 mm;
front edge (B, Fig.14) – workpiece max. 2 mm.
6. Start motor.
7. Feed workpiece straight across the infeed table holding your
fingers close together, guiding the workpiece with the palm of
your hands. Exert downward pressure on the workpiece only in
the infeed table area.
8. Switch machine off if no further cutting is to be done
immediately afterwards.
AB
FIG. 14
5.3. THICKNESS PLANER MODE
Note: Thickness planing is used to reduce a workpiece with one
already surface planed surface to a desired thickness.
- The workpiece is run through the thicknesser.
- The surface already planed flat rests on the thicknesser bed.
- The workpiece is cut on the upper side.
- The feed direction of the workpiece is exactly opposite than
with surface planing.
Workpiece dimensions
- Length: min. 200 mm; for workpieces over 1500 mm use a
second person for support.
- Width: max. 305 mm.
- Thickness: min 6 mm; max. 200 mm.
Note: The max. depth of cut for a single pass is 3 mm.
1. Turn clamping lever (B, Fig.15) outward and swing the outfeed
table (C, Fig.15) together with the fence to the left. Make sure
the outfeed table stopper (D, Fig.15) is engaged (When close the
outfeed table, please don't forget the release the stopper rst).
2. Turn the dust chute (E, Fig.15) with installed suction connector
to the machine .
3. Assume proper operating position:
- to feed the workpiece into the machine, position yourself offset
to one side of the feed opening.
B
C
E
D
FIG.15
- to remove the workpiece from the machine, position yourself
offset to one side of the outfeed opening.
-10-

5. To thickness plane stock which surfaces are not parallel, use
suitable feeding aids (make tting templates).
6. Set planing thickness.
7. Start motor.
8. Feed workpiece slowly and straight into the thicknesser. It will
then be automatically fed through the thicknesser.
9. Guide workpiece straight through the thicknesser.
10. Switch machine off if no further cutting is to be done immedi-
ately afterwards.
6. Maintenance
6.1 REPLACING CUTTER KNIVES
CAUTION! Risk of personal injury by cuts from the cutter knives!
Wear gloves when changing cutter knives.
To remove the cutter knives:
1. Unplug power cable.
2. Push fence back.
3. Raise cutterblock cover fully and pull extrusion fully outwards.
4. Turn the ve hexagon head screws of the cutter knife lockbar
fully in wear gloves! (Fig.16).
5. At rst remove cutter knife, then cutter knife lockbar from the
cutterblock.
6. Clean all surfaces of cutterblock and cutter knife lockbar with a
suitable solvent.
7. Place fresh cutter knife on cutter knife lockbar.
8. Place cutter knife lockbar with the tted cutter knife into the
cutterblock.
9. Check the projection of the knives:
- With the provided straight edge gauge .
- Place straight edge gauge across outfeed table and cutterblock
as shown.
- Turn cutterblock by hand one turn against the direction of feed.
- The cutter knives are set correctly if the straight edge is moved
forward 4 to 6 mm by the turning cutterblock. This check must be
performed at both ends of the cutterblock. (Fig.17)
10. To tighten the cutter knives, turn the ve hexagon head
screws of the cutter knife lockbar fully out. To prevent distortion of
the cutter knife lockbar start with the screws in the centre , then
tighten the screws closer to the edges step by step.(Fig.18)
Danger!
- Do not extend tool when tightening the screws.
- Do not tighten bolts by striking the wrench.
11. Return cutterblock cover to its starting position.
12. Pull fence forward.
FIG. 16
4 - 6 mm
FIG. 17
FIG. 18
-11-

A
B
C
6.2 Drive Belt Check
The cutterblock drive belt and the feedgear drive belt need to
be checked periodically and retightened if necessary. Both drive
belts are located behind the machine's side panel.
Checking the drive belt:
1. Unplug power cable.
2. Pull the fence (A, Fig.19) forward.
3. Take off the the side panel (B, Fig.19) and belt cover (C,
Fig.19).
4. Check belt tension with thumb pressure. The drive belt should
not give more than 10 mm in the centre.
Tensioning the drive belt:
5. From outside the machine, loosen the four nuts (D, Fig.20) –
using stick (E, Fig.20) to increase the motor, the cutterblock drive
belt will be slackened.
CAUSTION: When increase the motor by stick, don't damaged
the motor wiring box.
6. To tension the cutterblock drive belt, push the motor downward.
When belt tension is correct tighten motor mounting nuts (D,
Fig.20).
7. If necessary, remove chips and dust with dust collector or
brush.
8. Replace the side panel and belt cover secure with the screws.
FIG. 19
D
E
FIG.20
-12-

7. Diagrams & Components
1A 2A 3A 4A 5A
6A 7A 8A 9A
10A 11A
12A 13A 14A 15A 16A 17A 18A 19A
20A 21A 22A 23A 24A 25A 26A 27A 28A 29A 30A 31A
32A 33A 34A 35A 36A 37A 38A 39A 40A 41A 42A 43A
44A
NO. Description Part No. Qty.
1A Handle JL45030030A 1
2A Hex. Screw M8X20GB70B 2 3A Label JL45030031B 1
4A Left cover JL45032000C 1
5A Screw M6X12GB70D1Z 2 6A front cover assy JL45013000 1 7A Frame JL45010000F 1 8A Start knob LA39-B2-10-g 1 9A Switch box JL45090010 1
10A Stop knob LA39-B2-01-r 1 11A Screw M4X12GB70D1Z 4 12A switch plate JL45090009 1
13A Switch box JL45090011 1 14A Tapping screw ST3D5X16GB845Z 4 15A Big washer WSH6GB96B 4
16A Screw M6X12GB70D2B 8 17A Handle JL45030026 1
18A Plug P224E-13A 1 19A Pan screw M4X16GB823Z 4 20A Nut M8GB6172Z 4
21A Ball head bolt JL45030016 4 22A Scale JL45040019 1 23A Square neck bolt M12X65GB801Z 1 24A Hex. Screw M6X25GB70D2B 2 25A Plate JL45090003 1 26A Rod JL45090005 1 27A Nut M6GB41Z 2 28A Locknut M4GB889Z 2 29A Switch plate JL45090004 1
30A Switch QKS7 1 31A Pan screw M4X30GB818Z 2 32A Locknut M6GB889Z 2 33A Plat washer WSH6GB97D1Z 6 34A Hex.locknut M12GB889B 1 35A Idle pulley JL45052001 1
36A Ring CLP28GB893D1B 1 37A Bearing BRG6001-2ZGB276 1 38A Tube JL45052002 1 39A Adjust cushion JL40020004 1 40A Plate JL45052003 1 41A Handle spring JL45030032 2 42A Circlip CLP20GB894D1B 4 43A Handle JL45030014 1
44A Window plate JL45010004 1
-13-
7.1 Frame Assembly-SHEET A
Frame Assembly-SHEET A

16B
40B
3B 4B 8B
37B
15B
2B
23B
25B
38B
24B
42B 43B 45B44B
36B
21B
35B
5B
39B
19B
9B
18B
22B
28B
41B
11B
26B
7B
29B 30B
20B
6B1B
14B 17B
13B10B
31B
12B
33B
27B
32B 34B
No.
Description
Part No.
Qty.
1B
Cap nut
M6GB923Z
1
2B
Screw
M6X12GB70D2B
8
3B
Inner guide
JL45030023
1
4B
Wave washer
JL45020016
2
5B
Washer
JL45020017
2
6B
Big washer
WSH6GB96B
4
7B
Left cutterhead bracket
JL45020002
1
8B
Spring
JL41025102
1
9B
Shaft sleeve
JL45020006
4
10B
Location pin
JL45023001
1
11B
Outfeed roller
JL45020007
1
12B
Dust board
JL45020013
1
13B
Shaft
JL45020012
1
14B
Nut
M8GB6172Z
4
15B
Washer
WSH10GB97D1B
4
16B
Dust collector
JL45022000
1
17B
Hexagon bolt
M8X16GB5781Z
4
18B
Non-return block
JL45020010A
18
19B
Right cutterhead bracket
JL45020001
1
20B
Retainer ring
CLP52GB893D1B
2
21B
Washer
JL45051005
2
22B
Spring
JL45020004
4
23B
Screw
JL45020003
4
24B
Hexagon bolt
M10X25GB5783B
4
25B
Rod
JL45020009
1
26B
Bush
JL45020011
27
27B
Rod
JL45020008
1
28B
Infeed roller
JL45020005
1
29B
Big chain wheel
JL45050003
2
30B
Hexagonal self-locking nut
M10GB889Z
2
31B
Pin
PIN5X18GB879B
1
32B
Set screw
M6X8GB77B
1
33B
Flat washer
WSH16GB97D1Z
2
34B
Small eccentric wheel
JL45090002
1
35B
Hexagonal sunk screw
M6X20GB70D3B
6
36B
Square head screw
JL41010007
15
37B
Bar
JL45021003
3
38B
Knife
JL45021002
3
39B
Cutter shaft
JL45021001
1
40B
Bearing
BRG6205-DDUC3
2
41B
Right guard
JL45031000
1
42B
Big washer
WSH10GB96Z
2
43B
Set screw
M8X6GB77B
2
44B
Belt pulley for cutter shaft
JL45050001
1
45B
Flat key
PLN6X16GB1096
1
-14-
7.2 Tool Carrier Assembly-SHEET B Tool Carrier Assembly-SHEET B

26C 16C
7C
38C
18C 21C 28C
37C
24C 23C
29C
25C
22C 27C
31C
15C
36C5C
19C
39C
6C 2C 1C
30C
3C
32C
4C
14C
8C9C 34C10C
11C 13C 12C
20C
33C
17C
No. Description Part No. Qty.
Hexagon socket cap screw M6X45GB70Z 1
1Z 1 4 BG6Mt uN
Thread Tube JL45040006 1 Thread rod JL45040007 1 Bracket JL45040004B 1
Circlip CLP20GB894D1B 2 Lifting shaft JL45040009A 1
Hexagon socket cap screw M8X12GB70Z 3 Flat washer WSH8GB97D1Z 9
Flange plate JL45040028 1 Set screw M6X8GB77B 3
Position indicator JL09124D0E20 1
Hexagon socket cap screw M6X16GB70Z 1 Bearing BRG6202-2Z-P5GB276 1
4Z0716BG6Mt uN
Circlip ring CLP35GB893D1B 1 Locking lever JL45040008 1 Handwheel SGSL-D160-d12A1 1
Adjustable handle KTSB-1-B-M8X63X20 1
Thin nut M8GB6172Z 1 Flat washer WSH6GB97D1Z 4 Rings JL45040014 2 Screw M6X25GB70D2B 4
121004054LJd oR
Thicknesser table JL45040001A 1 Indicator JL45040020 1
Spring washer WSH10GB93Z 2 Hexagonal head screw M10X35GB5783B 2
1A20004054LJebuT
Set screw M8X20GB77B 5 Locking plate JL45040005 1 Locating sleeve JL45040003A 1
Spring washer WSH8GB93Z 2 Hexagon bolt M8X40GB5783Z 8 Shaft sleeve P23X20X15GB12613 1
201004054LJr a eG
Screw M6X12GB70D2B 3 Big washer WSH6GB96Z 3 Big washer WSH8GB96Z 2
1C 2C 3C 4C 5C 6C 7C 8C 9C
10C 11C 12C 13C 14C 15C 16C 17C 18C 19C 20C 21C 22C 23C 24C 25C 26C 27C 28C 29C 30C 31C 32C 33C 34C 35C 36C 37C 38C 39C
-15-
7.3 Press Planing Machine Assembly-SHEET C Press Planing Machine Assembly-SHEET C

26D 28D
19D
31D30D 33D32D
22D 23D21D
29D
24D
20D17D16D
10D9D8D7D6D
15D
11D5D
14D
4D2D 3D
13D
1D
12D
18D
25D 27D
No. Description Part No. Qty.
Handle sleeve JL45030028 1
Shoulder bolt JL45030017 1
131003054LJd oR
Small lever JL45030011 1 Hexagon socket cap screw M6X20GB70Z 2
Tighten rod JL45030008 1
1Z2716BG21Mt uN
Back rack JL45030007 1
Hex.screw M8X10GB77B 4
Washer JL45030029 4
Planer table JL45030001B 1 Cutterhead guard FDPT1202070000 1
Hand shank JL45030012 1 Locknut M12GB889B 2
Flat washer WSH12GB97D1Z 2 Eccentric shaft JL45030015 2
2B07BG06X8Mwe r cS
Thin nut M8GB6172Z 2 Hexagon bolt M8X16GB5781Z 1 Torsional spring JL45030009 1
Support JL45030005 1 Set screw M6X8GB77B 1
Big deflection wheel JL45090001 1
Back rack JL45030004 1 Guide plate JL45060028 1
2B07BG01X8Mwe r cS
Hex.screw M8X40GB77B 1 Hexagon self-locking nut M8GB889B 2 Back support bar JL45030027 1 Washer JL45030020 2
3Z3875BG03X8Mt l oB
Flat washer WSH8GB97D1Z 3 Hex.screw M8X12GB80B 4
1D 2D 3D 4D 5D 6D 7D 8D 9D
10D 11D 12D 13D 14D 15D 16D 17D 18D 19D 20D 21D 22D 23D 24D 25D 26D 27D 28D 29D 30D 31D 32D 33D
-16-
7.4 Discharging Platform Assembly-SHEET D Discharging Platform Assembly-SHEET D

25E21E
13E
22E
15E
29E
16E
27E 28E30E 31E32E
17E 18E 19E 20E
7E8E
4E 5E
3E
2E1E
11E
6E
12E
9E 10E
26E
23E 24E
14E
No. Description Part No. Qty.
Shoulder bolt JL45030017 2 Rod JL45030013 1
Hand shank JL45030012 1 Tighten rod JL45030008 1 Handle tube JL45030028 1 Plat washer WSH12GB97D1Z 2
Hex.screw M8X10GB77B 4 Washer JL45030029 4
Hex.screw M6X20GB70Z 3
Rod JL45030011 1
Locknut M12GB889B 2
Rising rack JL45030006 1 Planer table JL45030001B 1 Screw M8X16GB5781Z 1 Nut M8GB6170Z 1 Block JL45030018 1
Spring JL45030009 1 Support base JL45030005 1 Nut M8GB6172Z 4 Hex.screw M8X12GB70Z 1 Eccentric shaft JL45030015 2 Screw M8X60GB70B 2 Front Rack JL45030003 1 Screw M8X10GB70B 2 Hex.screw M8X40GB77B 1 Guide plate JL45060028 1 Support bar JL45030010 1 Washer JL45030020 2
Locknut M8GB889Z 2 Blot M8X30GB5783Z 3 Plat washer WSH8GB97D1Z 3
Hex.screw M8X12GB80B 4
1E 2E 3E 4E 5E 6E 7E 8E 9E
10E 11E 12E 13E 14E 15E 16E 17E 18E 19E 20E 21E 22E 23E 24E 25E 26E 27E 28E 29E 30E 31E 32E
-17-
7.5 Feed Table Assembly-SHEET E Feed Table Assembly-SHEET E

15F
10F
18F22F 23F 24F
26F 27F
11F 12F
25F
13F
8F6F
19F
5F4F7F1F
20F
2F
9F
3F
14F 16F 17F
21F
No. Description Part No. Qty.
Hexagon socket cap screw M8X25GB70B 4 Washer WSH8GB97D1Z 4 Motor YSKA905222A 1 Big washer WSH8GB5287Z 4
Cap nut M8GB923Z 4 Spring washer WSH8GB93Z 4 Socket head cap screw M8X12GB77Z 2
Motor pulley JL45050002 1 Self-locking nut M10GB889Z 1
Belt wheel JL45051101 1 Bearing BRG6000-2ZGB276 2 Circlip ring CLP10GB894D1B 2 V-belt JL45050007 1
Chain wheel spindle JL45051004 1
Washer WSH10GB97D1Z 1 Panel assembly JL45051300 1 Handle sleeve JL45050013 1
Big gearwheel JL45051001 1
Belt wheel spindle JL45051301 1
Minor sprocket bush JL45051003 1 Washer JL45051005 1
Circlip ring CLP15GB894D1B 1 Set screw M5X10GB77B 2 Small gearwheel JL45051102 1
130115054LJhsuB
Chain JL45050008 1 V-belt JL45050009 1
1F 2F 3F 4F 5F 6F 7F 8F 9F
10F 11F 12F 13F 14F 15F 16F 17F 18F 19F 20F 21F 22F 23F 24F 25F 26F 27F
-18-
7.6 Drive System Assembiy-SHEET F Drive System Assembiy-SHEET F

1G 2G 3G 4G
7G 6G 5G 8G 9G
10G 11G
14G 15G 16G17G18G
23G 28G
31G 30G 29G
27G 24G 22G 21G 20G
19G
25G 26G
12G 13G
No. Description Part No. Qty.
1GNut M6GB889Z 2 2GSupport base JL45060002 2 3GHex. Screw M6X16GB70D3Z 2 4GHex. Screw M8X16GB70Z 2 5GWasher WSH12GB97D1Z 2 6GDisc spring washer JL46062006 2 7GWasher WSH8GB97D1Z 2 8GNut M8GB6170Z 2 9GLocknut M8X60GB80B 2
10GCap nut M6GB923Z 4 11GHex. Screw M6X12GB70D3Z 2 12GRight support arm JL45060020 1 13GNut M8GB6172Z 2 14GLock tube JL45060024 2 15GLock rod JL45060023 1 16GLock handle JL45060027 1 17GHex. Screw M6X16GB70Z 2 18GAngle label JL45060007B 1 19GHex. Screw M8X20GB70Z 2 20GLeft support arm JL45060021 1 21GSupport plate JL45063000A 1 22GBig washer WSH6GB96Z 6 23GIndicator JL45060026 1 24GWasher WSH4GB97D1Z 2 25GHex. Screw M4X5GB70Z 2 26GSpring washer WSH4GB93Z 2 27GCap nut M8GB923Z 2 28GThick washer FDPT1202060016 2 29GSquare nut M8GB39Z 2 30GLong pin JL45060011 2 31GRip fence JL45060001 1
-19-
7.7 Material Bafe Assembly-SHEET G Material Bafe Assembly-SHEET G