woodmizer LT30 Manual instruction

Wood-Mizer® Sawmill
Safety, Setup, Operation
& Maintenance Manual
LT30 Super rev. F7.00 - J2.00
LT40 Super rev. F8.00 - J3.00
Safety is our #1 concern! Read and understand
all safety information and instructions before oper-
ating, setting up or maintaining this machine.
October 2004 Form #761

Table of Contents Section-Page
ii 30S97doc041910 Table of Contents
SECTION 1 INTRODUCTION 1-1
1.1 About This Manual.................................................................................1-1
1.2 Customer and Sawmill Identification.....................................................1-2
1.3 Getting Service.......................................................................................1-4
General Contact Information................................................1-4
Branches & Authorized Sales Centers..................................1-5
1.4 Specifications .........................................................................................1-7
SECTION 2 SAFETY 2-1
2.1 Safety Symbols.......................................................................................2-1
2.2 Safety Instructions..................................................................................2-2
SECTION 3 SAWMILL SETUP 3-1
3.1 Stationary Sawmill Setup.......................................................................3-1
3.2 Portable Sawmill Setup ..........................................................................3-3
3.3 Replacing The Blade ..............................................................................3-8
3.4 Tensioning The Blade.............................................................................3-9
3.5 Tracking The Blade..............................................................................3-10
3.6 Starting The Engine (or Motor)............................................................3-12
3.7 Board Return ........................................................................................3-13
SECTION 4 SAWMILL OPERATION 4-1
4.1 Loading, Turning And Clamping Logs..................................................4-1
4.2 Up/Down Operation ...............................................................................4-3
4.3 Blade Guide Arm Operation...................................................................4-4
4.4 Clutch/Brake Operation..........................................................................4-5
4.5 Power Feed Operation............................................................................4-7
4.6 Cutting The Log .....................................................................................4-9
4.7 Edging...................................................................................................4-11
4.8 Optional Cutting Procedure for Super Series Mills..............................4-12
4.9 Blade Height Scale...............................................................................4-13
4.10 Water Lube Operation..........................................................................4-16
4.11 Preparing The Sawmill For Towing.....................................................4-18
SECTION 5 MAINTENANCE 5-1
5.1 Wear Life................................................................................................5-1
5.2 Blade Guides ..........................................................................................5-2
EZ-Glide Guide Blocks .........................................................5-2
Ceramic Guide Disks............................................................5-4
5.3 Sawdust Removal...................................................................................5-8
5.4 Carriage Track, Wiper & Scrapers.........................................................5-9
5.5 Vertical Mast Rails...............................................................................5-11
5.6 Drum Switches .....................................................................................5-12
5.7 Miscellaneous.......................................................................................5-13
5.8 Blade Tensioner....................................................................................5-15
5.9 Blade Wheel Belts................................................................................5-17
TOC

Table of Contents Section-Page
Table of Contents 30S97doc041910 iii
5.10 Brake Strap Adjustment .......................................................................5-18
5.11 Drive Belt Adjustment..........................................................................5-20
5.12 Clutch Handle Detent Adjustment........................................................5-23
5.13 Drive Bearing .......................................................................................5-24
5.14 Up/Down System..................................................................................5-26
5.15 Power Feed...........................................................................................5-30
5.16 Charging The Battery...........................................................................5-34
MAINTENANCE LOG 5-36
SECTION 6 TROUBLESHOOTING GUIDE 6-1
6.1 Sawing Problems....................................................................................6-1
6.2 Electrical Problems.................................................................................6-3
6.3 Power Feed Problems.............................................................................6-7
6.4 Power Feed Circuit Troubleshooting......................................................6-9
LT30 Super Rev. G6.00+
LT40 Super Rev. G7.00+.................................................6-9
LT30 Super Rev. F7.00 - G5.00
LT40 Super Rev. F8.00 - G6.00.....................................6-10
6.5 Engine/Motor and Drive Pulleys Alignment........................................6-12
6.6 Power Feed Variable Feed Rate Switch Test.......................................6-13
6.7 Power Feed Preliminary Test ...............................................................6-14
6.8 Power Feed Mechanical Test................................................................6-15
6.9 Fuse Terminal Extension Stud..............................................................6-16
6.10 Circuit Breaker Operation ....................................................................6-18
LT30 Super Rev. G3.00+
LT40 Super Rev. G4.00+...............................................6-18
LT30 Super Rev. F7.00 - G2.01
LT40 Super Rev. F8.00 - G3.01.....................................6-19

Table of Contents Section-Page
iv 30S97doc041910 Table of Contents
SECTION 7 SAWMILL ALIGNMENT 7-1
7.1 Routine Alignment Procedure................................................................7-1
Blade Installation..................................................................7-1
Saw Head Tilt .....................................................................7-2
Blade Guide Arm Alignment.................................................7-4
Blade Guide Vertical Tilt Alignment.....................................7-9
Blade Guide Horizontal Tilt Adjustment.............................7-11
Blade Guide Flange Spacing ..............................................7-14
Side Support Alignment.......................................................7-16
Blade Height Scale Adjustment...........................................7-18
7.2 Complete Alignment Procedure...........................................................7-19
Frame Setup ...................................................................7-19
Blade Installation................................................................7-20
Saw Head Slide Pad Adjustment.........................................7-21
Blade Wheel Alignment.......................................................7-23
Track Roller Adjustment .....................................................7-29
Bed Rail Adjustment............................................................7-33
Blade Guide Installation.....................................................7-36
Blade Guide Arm Alignment...............................................7-38
Blade Guide Deflection.......................................................7-43
Blade Guide Vertical Tilt Alignment...................................7-45
Blade Guide Horizontal Tilt Adjustment.............................7-47
Blade Guide Flange Spacing ..............................................7-50
Side Support Alignment.......................................................7-52
Clamp Stop/Stop Bolt Adjustment.......................................7-54
Saw Head Tilt ...................................................................7-55
Blade Height Scale Adjustment...........................................7-57
Board Return Bracket .........................................................7-58
INDEX I

Introduction
About This Manual
Introduction 30S97doc041910 1-1
1
SECTION 1 INTRODUCTION
1.1 About This Manual
This manual is to replace or to be used with all previous information received on the
Wood-Mizer®* sawmill. All future mailings will be an addition to or a revision of individual
sections of this manual as we obtain new information.
The information and instructions given in this manual do not amend or extend the limited
warranties for the equipment given at the time of purchase.
For general information regarding Wood-Mizer and our “Forest to Final Form” products,
please refer to the All Products Catalog in your support package.
*Wood-Mizer®is a registered trademark of Wood-Mizer Products, Inc.
Sawmill U.S. Patent Nos.: 4,878,411
MILL COMPONENTS
Engine/Drive Assembly
Cutting Head
Outer Blade Guide Arm
Blade
Tensioner Side Support
Log Clamp
Loading Ramps
Bed Frame Outrigger Leg
Pivot Bed Rail
Control
Panel
Water Lube
Clutch/Brake Handle
Trailer
Hitch
300001

Introduction
Customer and Sawmill Identification
1
1-2 30S97doc041910 Introduction
1.2 Customer and Sawmill Identification
Each Wood-Mizer sawmill has a model number and a 17-digit Vehicle Identification Num-
ber (VIN). In addition, when you pick up your mill, you will receive a customer number.
These three numbers will help expedite our service to you. Please locate them now and
write them below so you have quick, easy access to them. See the following figures for
model number and V.I.N. descriptions and locations.
(To be filled in by purchaser)
Mill Model ___________________
Mill VIN ___________________
Customer No. ___________________
See below for a description of the V.I.N.
LT30 E25
Basic Sawmill I.D. Engine/Motor
Configuration
MODEL NUMBER DESCRIPTION
Company Identification Number
456=Wood-Mizer Indiana
Weight Class; A=Under 3,000 lbs B=3,001-4,000 lbs
C=4,001-5,000 lbs D=5,001-6,000 lbs
Product No.; 2=LT20/25/27, 3=LT30/40, 4=LT30HD/40HD,
5=LT30/40 Super, 6=LT30HD/40HD Super, 7=LT60/70/80
Length of the Trailer;
20=20 Ft., 24=24’, 35=35’
Number of axles on the trailer
Check Digit
Add all the numbers and divide by 11
Year of Manufacture;
X=1999, Y=2000, 1=2001, 2=2002, 3=2003, etc...
State of Manufacture
N=Indiana, P=Poland
Month of Manufacture
A=January, B=February, C=March, etc...
Revision Level
Sequence Number
Ranging from 000-999
End of 17-Digit VIN
Revision Level (Repeated)
Two-Digit Minor Revision Level
456 A 5 24 1 X S N A F9 017 F9 .01
V.I.N. DESCRIPTION.

Introduction
Customer and Sawmill Identification
Introduction 30S97doc041910 1-3
1
The model number and V.I.N. can be found in the following locations.
MODEL NUMBER AND V.I.N. LOCATIONS.
2
1
3
300
11
9

Introduction
Getting Service
1
1-4 30S97doc041910 Introduction
1.3 Getting Service
Wood-Mizer is committed to providing you with the latest technology, best quality and
strongest customer service available on the market today. We continually evaluate our
customers’ needs to ensure we’re meeting current wood-processing demands. Your com-
ments and suggestions are welcome.
General Contact Information
Toll free phone numbers are listed below for the continental U.S. and Canada. See the
next page for contact information for specific Wood-Mizer locations.
Office Hours: All times are Eastern Standard Time.
Please have your vehicle identification number and your customer number ready when
you call.
Wood-Mizer will accept these methods of payment:
Visa, Mastercard, or Discover
COD
Prepayment
Net 15 (with approved credit)
Be aware that shipping and handling charges may apply. Handling charges are based on
size and quantity of order. In most cases, items will ship on the day they are ordered.
Second Day and Next Day shipping are available at additional cost.
If your sawmill was purchased outside the United States or Canada, contact the distribu-
tor for service.
United States Canada
Sales 1-800-553-0182 1-877-866-0667
Service 1-800-525-8100 1-877-866-0667
Website www.woodmizer.com www.woodmizer.ca
E-mail [e-mail] [e-mail]
Monday - Friday Saturday
(Indianapolis Office Only) Sunday
8 a.m. to 5 p.m. 8 a.m. to 12 p.m. Closed

Introduction
Branches & Authorized Sales Centers
Introduction 30S97doc041910 1-5
1
Branches & Authorized Sales Centers
UNITED STATES CANADA
1 World Headquarters
8180 W. 10th Street
Indianapolis, IN 46214-2400
Phone [phone]
Fax [phone]
15 Canadian Headquarters
217 Salem Road
Manilla, ON K0M 2J0
Phone [phone]
Fax [phone]
Wood-Mizer Branches Authorized Sales Centers* Wood-Mizer Canada
Branches
2 Wood-Mizer Northeast
8604 State Route 104
Hannibal, NY 13074
Phone [phone]
Fax [phone]
6 California
6980 Camp Far West Road
Sheridan, CA 95681
Phone [phone]
Fax [phone]
E-mail [e-mail]
16 Wood-Mizer Canada East
Box 173, 1082 #1 Hwy
Aylesford, NS B0P 1C0
Phone/Fax [phone]
3 Wood-Mizer Portland
24435 N.E. Sandy Blvd.
Wood Village, OR 97060
Phone [phone]
Fax [phone]
7 Maine
541 Borough Road
Chesterville, ME 04938
Phone [phone]
Fax [phone]
E-mail [email protected]
17 Wood-Mizer Canada Quebec
422 Rte. du Canton (Rte. 148)
Chatham, QC J8G 1R1
Phone [phone]
Fax [phone]
4 Wood-Mizer South
74 Pine Road
Newnan, GA 30263-5141
Phone [phone]
Fax [phone]
8 New Mexico
425 Bibb Industrial Drive
Las Vegas, NM 87701
Phone [phone]
Fax [phone]
E-mail [email protected]
18 Wood-Mizer Canada West
4770 46th Avenue S.E.
Salmon Arm, BC V1E 2W1
Phone [phone]
Fax [phone]
17
2
7
19
15
12
16
4
18
6
3
810
11
5
13
14
20
19

Introduction
Branches & Authorized Sales Centers
1
1-6 30S97doc041910 Introduction
5 Wood-Mizer Missouri
9664 Lawrence 2130
NMt. Vernon, MO 65712
Phone [phone]
Fax [phone]
9 Pennsylvania
HCR 75 (Off Old Road 522)
Shade Gap, PA 17255
Phone [phone]
Fax [phone]
E-mail [email protected]
Authorized Sales Centers*
19 Ontario North
41 Rubin Drive
Murillo, ON P0T 2T0
Phone [phone]
Fax [phone]
10 North Carolina
28002 Canton Road
Albemarle, NC 28001
Phone [phone]
Fax [phone]
E-mail [e-mail]
20 East New Brunswick
161 Ave. De L’Eglise
St. Antoine, NB E4V 1M2
Phone [phone]
Fax [phone]
11 Alaska
HCO5 9821
Palmer, AK 99645
Phone [phone]
Fax [phone]
E-mail [email protected]
12 Wisconsin
2201 Highway O
Mosinee, WI 54455
Phone [phone]
E-mail [email protected]
13 Montana
51 Basin Creek Road
Basin, MT 59631
Phone [phone]
Fax [phone]
E-mail [email protected]
14 Mississippi
123 Cable Bridge Road
Perkinston, MS 39573
Phone [phone]
*Authorized Sales Centers offer lim-
ited services such as sawmill
demos and training, routine service
and sales of blades and common
relacement parts

Introduction
Specifications
Introduction 30S97doc041910 1-7
1
1.4 Specifications
Model: LT30 Super Rev. H4.00 - J3.04
Dimensions: Length: 21'-11"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 11'-0"
Bed Height (Ground To Bed): 30"
Weights: G36 E25 D42 D51
Basic Unit (Wet): 2582 lbs 2713 lbs 2763 lbs
With Trailer: 2904 lbs 3035 lbs 3085 lbs
Tongue Weight: 80 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1870 lbs
Tire Size: ST215/75R14
Weight: 322 lbs
Log Capacity: Length: 16'-8"
Length (w/Operator Seat Option): 14'-8"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G36 E25 D42 D51
Manufacturer: Nissan Lincoln Kubota Caterpillar
Fuel: Gas Electric Diesel Diesel
Horsepower Rating: 36 25 42 51
Weight: 235 435 485
Idle Speed: 1500 RPM 3600 RPM 1500 RPM 1500 RPM
High Throttle Speed (No Load): 3600 RPM 3600 RPM 3200 RPM 3100 RPM
Noise Level - @ operator position: 83 dBA 98 dBA 98 dBA 92 dBA
Noise Level - 20 feet away: 67 dBA 90 dBA 87 dBA 84 dBA
Blade Speed (No Load): 5700 sfpm 5800 sfpm 5700 sfpm sfpm
Fuel Consumption (per hour): 1.0 Gal. 20 KwHr 1 Gal. 1.5 gal
Cooling System: Water Air Water Water
Coolant Capacity: 1.65 Gal. 1.75 Gal.
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 7/16" 1 7/16"
Drive Pulley: 4.15" 4TB38 3TB42 4.46"
Drive Belt: 3/5v750 3/5v750 3/5v750 3/5VFL770
Blade Braking: 1 Second 1 Second 1 Second 1 Second
Oil Capacity w/Filter: 4 qts. N/A 6.7 qts. 10 qts.
Battery: 12V 1125CCA 12V 1125CCA 12V 1125CCA 12V 1125CCA
Alternator Output: 140 Amp 140 Amp 140 Amp 140 Amp
A
lternator Belt: 6PK425 6PK425 6PK425 6PK1055
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec. 13.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec. 9.0 sec.
Hourly Production (Average range w/experienced
operators/average size logs): 375-500 bdft.
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Accuset: 13 lbs ±1/32" per drop
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs

Introduction
Specifications
1
1-8 30S97doc041910 Introduction
Model: LT40 Super Rev. H5.00 - J4.05
Dimensions: Length: 26'-2"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 11'-0"
Bed Height (Ground To Bed): 30"
Weights: G36 E25 D42 D51
Basic Unit (Wet): 2784 lbs 2913 lbs 2963 lbs
With Trailer: 3106 lbs 3235 lbs 3285 lbs
Tongue Weight: 82 lbs 75 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1870 lbs
Tire Size: ST215/75R14
Weight: 322 lbs
Log Capacity: Length: 21'-0"
Length (w/Operator Seat Option): 19'-0"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G36 E25 D42 D51
Manufacturer: Nissan Lincoln Kubota Caterpillar
Fuel: Gas Electric Diesel Diesel
Horsepower Rating: 36 25 42 51
Weight: 235 435 485
Idle Speed: 1500 RPM 3600 RPM 1500 RPM 1500 RPM
High Throttle Speed (No Load): 3600 RPM 3600 RPM 3200 RPM 3100 RPM
Noise Level - @ operator position: 83 dBA 98 dBA 98 dBA 92 dBA
Noise Level - 20 feet away: 67 dBA 90 dBA 87 dBA 84 dBA
Blade Speed (No Load): 5700 sfpm 5800 sfpm 5700 sfpm sfpm
Fuel Consumption (per hour): 1.0 Gal. 20 KwHr 1 Gal. 1.5 gal
Cooling System: Water Air Water Water
Coolant Capacity: 1.65 Gal. 1.75 Gal.
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 7/16" 1 7/16"
Drive Pulley: 4.15" 4TB38 3TB42 4.46"
Drive Belt: 3/5v750 3/5v750 3/5v750 3/5VFL770
Blade Braking: 1 Second 1 Second 1 Second 1 Second
Oil Capacity w/Filter: 4 qts. N/A 6.7 qts. 10 qts.
Battery: 12V 1125CCA 12V 1125CCA 12V 1125CCA 12V 1125CCA
Alternator Output: 140 Amp 140 Amp 140 Amp 140 Amp
A
lternator Belt: 6PK425 6PK425 6PK425 6PK1055
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec. 13.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec. 9.0 sec.
Hourly Production (Average range w/experienced
operators/average size logs): 375-500 bdft.
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Accuset: 13 lbs ±1/32" per drop
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs

Introduction
Specifications
Introduction 30S97doc041910 1-9
1
Dimensions: Length: 21'-11"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 9'-11"
Bed Height (Ground To Bed): 30"
Weights: G35 E25 D42
Basic Unit (Wet): 2582 lbs 2713 lbs
With Trailer: 2904 lbs 3035 lbs
Tongue Weight: 80 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1870 lbs
Tire Size: ST215/75R14
Weight: 322 lbs
Log Capacity: Length: 16'-8"
Length (w/Operator Seat Option): 14'-8"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G35 E25 D42
Manufacturer: Wisconsin Lincoln Kubota
Fuel: Gas Electric Diesel
Horsepower Rating: 35 25 42
Weight: 412 lbs 235 lbs 435 lbs
Idle Speed: 1500 RPM 3600 RPM 1500 RPM
High Throttle Speed (No Load): 3200 RPM 3600 RPM 3200 RPM
Noise Level (@ High Throttle, No Blade)
@ operator position: 102 dBA 98 dBA 98 dBA
20 feet away: 95 dBA 90 dBA 87 dBA
Blade Speed (No Load): 5650 sfpm 5800 sfpm 5700 sfpm
Fuel Consumption (per hour): 1 1/2 Gal. 20 KwHr 1 Gal.
Cooling System: Air Air Water
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 9/16"
Drive Pulley: 4TB42-P1 4TB38 3TB42
Drive Belt: 3BX74 3BX72 3BX72
Blade Braking: 1 Second 1 Second 1 Second
Oil Capacity w/Filter: 4 qts. N/A 6.7 qts.
Battery: 12V 1125CCA 12V 1125CCA 12V 1125CCA
Alternator Output: 140 Amp 140 Amp 140 Amp
A
lternator Belt: 6PK425 6PK425 6PK425
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec.
Hourly Production (Average range w/experienced
operators/average size logs):
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Setworks: 13 lbs
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs
Model:LT30 SuperRev.G9.00-H3.00

Introduction
Specifications
1
1-10 30S97doc041910 Introduction
Dimensions: Length: 26'-2"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 9'-11"
Bed Height (Ground To Bed): 30"
Weights: G35 E25 D42
Basic Unit (Wet): 2784 lbs 2913 lbs
With Trailer: 3106 lbs 3235 lbs
Tongue Weight: 82 lbs 75 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1870 lbs
Tire Size: ST215/75R14
Weight: 322 lbs
Log Capacity: Length: 21'-0"
Length (w/Operator Seat Option): 19'-0"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G35 E25 D42
Manufacturer: Wisconsin Lincoln Kubota
Fuel: Gas Electric Diesel
Horsepower Rating: 35 25 42
Weight: 412 lbs 235 lbs 435
Idle Speed: 1500 RPM 3600 RPM 1500 RPM
High Throttle Speed (No Load): 3200 RPM 3600 RPM 3200 RPM
Noise Level (@ High Throttle, No Blade)
@ operator position: 102 dBA 98 dBA 98 dBA
20 feet away: 95 dBA 90 dBA 87 dBA
Blade Speed (No Load): 5650 sfpm 5800 sfpm 5700 sfpm
Fuel Consumption (per hour): 1 1/2 Gal. 20 KwHr 1 Gal.
Cooling System: Air Air Water
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 9/16"
Drive Pulley: 4TB42-P1 4TB38 3TB42
Drive Belt: 3BX74 3BX72 3BX72
Blade Braking: 1 Second 1 Second 1 Second
Oil Capacity w/Filter:
Battery: 12V 1125CCA 12V 1125CCA 12V 1125CCA
Alternator Output: 140 Amp 140 Amp 140 Amp
A
lternator Belt: 6PK425 6PK425 6PK425
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec.
Hourly Production (Average range w/experienced
operators/average size logs):
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Setworks: 13 lbs
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs
Model:LT40 SuperRev.H1.00-H4.00

Introduction
Specifications
Introduction 30S97doc041910 1-11
1
Dimensions: Length: 21'-11"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 9'-10"
Bed Height (Ground To Bed): 30"
Weights: G35 E25 D40
Basic Unit (Wet): 2582 lbs
With Trailer: 2904 lbs
Tongue Weight: 80 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1870 lbs
Tire Size: ST215/75R14
Weight: 322 lbs
Log Capacity: Length: 16'-8"
Length (w/Operator Seat Option): 14'-8"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G35 E25 D40
Manufacturer: Wisconsin Lincoln Lombardini
Fuel: Gas Electric Diesel
Horsepower Rating: 35 25 40
Weight: 412 lbs 235 lbs 355 lbs
Idle Speed: 1500 RPM 3600 RPM 1500 RPM
High Throttle Speed (No Load): 3200 RPM 3600 RPM 3200 RPM
Noise Level (@ High Throttle, No Blade)
@ operator position: 102 dBA 98 dBA 102 dBA
20 feet away: 95 dBA 90 dBA 94 dBA
Blade Speed (No Load): 5650 sfpm 5800 sfpm 5650 sfpm
Fuel Consumption (per hour): 1 1/2 Gal. 20 KwHr 1 Gal.
Cooling System: Air Air Water
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 9/16"
Drive Pulley: 4TB42-P1 4TB38 3TB42
Drive Belt: 3BX74 3BX72 3BX72
Blade Braking: 1 Second 1 Second 1 Second
Oil Capacity w/Filter: N/A
Battery: 12V 1000CCA 12V 1000CCA 12V 1000CCA
Alternator Output: 105 Amp 105 Amp 105 Amp
A
lternator Belt: 6PK1015 6PK1015 6PK1015
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec.
Hourly Production (Average range w/experienced
operators/average size logs):
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Setworks: 13 lbs
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs
Model:LT30 SuperRev.G3.00-G8.00
Pa
g
e 1

Introduction
Specifications
1
1-12 30S97doc041910 Introduction
Dimensions: Length: 26'-2"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 9'-10"
Bed Height (Ground To Bed): 30"
Weights: G35 E25 D40
Basic Unit (Wet): 2784 lbs 2823 lbs
With Trailer: 3106 lbs 3145 lbs
Tongue Weight: 82 lbs 75 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1870 lbs
Tire Size: ST215/75R14
Weight: 322 lbs
Log Capacity: Length: 21'-0"
Length (w/Operator Seat Option): 19'-11"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G35 E25 D40
Manufacturer: Wisconsin Lincoln Lombardini
Fuel: Gas Electric Diesel
Horsepower Rating: 35 25 40
Weight: 412 lbs 235 lbs 355 lbs
Idle Speed: 1500 RPM 3600 RPM 1500 RPM
High Throttle Speed (No Load): 3200 RPM 3600 RPM 3200 RPM
Noise Level (@ High Throttle, No Blade)
@ operator position: 102 dBA 98 dBA 102 dBA
20 feet away: 95 dBA 90 dBA 94 dBA
Blade Speed (No Load): 5650 sfpm 5800 sfpm 5650 sfpm
Fuel Consumption (per hour): 1 1/2 Gal. 20 KwHr 1 Gal.
Cooling System: Air Air Water
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 9/16"
Drive Pulley: 4TB42-P1 4TB38 3TB42
Drive Belt: 3BX74 3BX72 3BX72
Blade Braking: 1 Second 1 Second 1 Second
Oil Capacity w/Filter: N/A
Battery: 12V 1000CCA 12V 1000CCA 12V 1000CCA
Alternator Output: 105 Amp 105 Amp 105 Amp
A
lternator Belt: 6PK1015 6PK1015 6PK1015
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec.
Hourly Production (Average range w/experienced
operators/average size logs):
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Setworks: 13 lbs
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs
Model:LT40 SuperRev.G4.00-G9.00

Introduction
Specifications
Introduction 30S97doc041910 1-13
1
Dimensions: Length: 21'-11"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 9'-10"
Bed Height (Ground To Bed): 30"
Weights: G35 E25 D40
Basic Unit (Wet): 2582 lbs
With Trailer: 2870 lbs
Tongue Weight: 80 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1875 lbs
Tire Size: LT185R14C-D
Weight: 288 lbs
Log Capacity: Length: 16'-8"
Length (w/Operator Seat Option): 14'-8"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G35 E25 D40
Manufacturer: Wisconsin Lincoln Lombardini
Fuel: Gas Electric Diesel
Horsepower Rating: 35 25 40
Weight: 412 lbs 235 lbs 355 lbs
Idle Speed: 1500 RPM 3600 RPM 1500 RPM
High Throttle Speed (No Load): 3200 RPM 3600 RPM 3200 RPM
Noise Level (@ High Throttle, No Blade)
@ operator position: 102 dBA 98 dBA 102 dBA
20 feet away: 95 dBA 90 dBA 94 dBA
Blade Speed (No Load): 5650 sfpm 5800 sfpm 5650 sfpm
Fuel Consumption (per hour): 1 1/2 Gal. 20 KwHr 1 Gal.
Cooling System: Air Air Water
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 9/16"
Drive Pulley: 4TB42-P1 4TB38 3TB42
Drive Belt: 3BX74 3BX72 3BX72
Blade Braking: 1 Second 1 Second 1 Second
Oil Capacity w/Filter: N/A
Battery: 12V 1000CCA 12V 1000CCA 12V 1000CCA
Alternator Output: 105 Amp 105 Amp 105 Amp
A
lternator Belt: 6PK1015 6PK1015 6PK1015
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec.
Hourly Production (Average range w/experienced
operators/average size logs):
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Setworks: 13 lbs
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs
Model:LT30 SuperRev.F7.00-G2.01

Introduction
Specifications
1
1-14 30S97doc041910 Introduction
Dimensions: Length: 26'-2"
Width: 6'-6"
Height (Ground To Mast): 7'-8"
Height (Max Head Position): 9'-10"
Bed Height (Ground To Bed): 30"
Weights: G35 E25 D40
Basic Unit (Wet): 2784 lbs 2823 lbs
With Trailer: 3072 lbs 3111 lbs
Tongue Weight: 82 lbs 75 lbs
Trailer: Axle Capacity: 3500 lbs
Tire Capacity: 1875 lbs
Tire Size: LT185R14C-D
Weight: 288 lbs
Log Capacity: Length: 21'-0"
Length (w/Operator Seat Option): 19'-0"
Diameter: 36"
Weight: 4400 lbs
Max Clamp Width (from stop block): 26.5"
Max Throat Width (guide to guide): 28"
Max Cant Width (outer guide to stop block): 25"
Engine: G35 E25 D40
Manufacturer: Wisconsin Lincoln Lombardini
Fuel: Gas Electric Diesel
Horsepower Rating: 35 25 40
Weight: 412 lbs 235 lbs 355 lbs
Idle Speed: 1500 RPM 3600 RPM 1500 RPM
High Throttle Speed (No Load): 3200 RPM 3600 RPM 3200 RPM
Noise Level (@ High Throttle, No Blade)
@ operator position: 102 dBA 98 dBA 102 dBA
20 feet away: 95 dBA 90 dBA 94 dBA
Blade Speed (No Load): 5650 sfpm 5800 sfpm 5650 sfpm
Fuel Consumption (per hour): 1 1/2 Gal. 20 KwHr 1 Gal.
Cooling System: Air Air Water
Drive Shaft O.D.: 1 7/16" 1 5/8" 1 9/16"
Drive Pulley: 4TB42-P1 4TB38 3TB42
Drive Belt: 3BX74 3BX72 3BX72
Blade Braking: 1 Second 1 Second 1 Second
Oil Capacity w/Filter: N/A
Battery: 12V 1000CCA 12V 1000CCA 12V 1000CCA
Alternator Output: 105 Amp 105 Amp 105 Amp
A
lternator Belt: 6PK1015 6PK1015 6PK1015
Rates: Forward (no cutting): 180 ft./min.
Reverse: 200 ft./min.
Up (24"): 17.3 sec. 13.3 sec. 14.3 sec.
Down (24"): 10.6 sec. 9.7 sec. 9.5 sec.
Hourly Production (Average range w/experienced
operators/average size logs):
Options: Single/Lap Siding Option: 143 lbs
Manual Turner: 44 lbs
Manual Toeboards: 17 lbs
Manual Winch: 33 lbs
Debarker: 69 lbs
Resaw Attachment: 231 lbs
Laser Sight: 2.5 lbs
Setworks: 13 lbs
6' Bed Extension: 390 lbs
12' Bed Extension: 758 lbs
24' Bed Extension: 1122 lbs
Operator Seat: 112 lbs
Model:LT40 SuperRev.F8.00-G3.01

Safety
Safety Symbols
Safety 30S97doc041910 2-1
2
SECTION 2 SAFETY
2.1 Safety Symbols
The following symbols and signal words call your attention to instructions concerning your
personal safety. Be sure to observe and follow these instructions.
DANGER! indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING! suggests a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION! refers to potentially hazardous situations which,
if not avoided, may result in minor or moderate injury or
damage to equipment.
IMPORTANT! indicates vital information.
NOTE: gives helpful information.
Warning stripes are placed on areas where a single decal
would be insufficient. To avoid serious injury, keep out of
the path of any equipment marked with warning stripes.

Safety
Safety Instructions
2
2-2 30S97doc041910 Safety
2.2 Safety Instructions
NOTE: ONLY safety instructions regarding personal injury are listed in this section. Cau-
tion statements regarding only equipment damage appear where applicable throughout
the manual.
OBSERVE SAFETY INSTRUCTIONS
IMPORTANT! Read the entire Operator's Manual before operating
the sawmill. Take notice of all safety warnings throughout this man-
ual and those posted on the machine. Keep this manual with this
machine at all times, regardless of ownership.
Also read any additional manufacturer’s manuals and observe any
applicable safety instructions including dangers, warnings, and
cautions.
Only persons who have read and understood the entire operator's
manual should operate the sawmill. The sawmill is not intended for
use by or around children.
IMPORTANT! It is always the owner's responsibility to comply with
all applicable federal, state and local laws, rules and regulations
regarding the ownership, operation and towing of your Wood-Mizer
sawmill. All Wood-Mizer mill owners are encouraged to become
thoroughly familiar with these applicable laws and comply with
them fully while using or towing the mill.