Woodpecker PT 3 User manual

Content
1. The installation and components of equipment ............................................... 1
2. Installation and adjustment .............................................................................. 4
3. Maintenance and sterilization ........................................................................... 4
4. Precaution ........................................................................................................ 7
5. After service ..................................................................................................... 9
6. Environmental protection ................................................................................. 9
7. Manufacturer’s right ........................................................................................ 9
8. Symbol instruction ........................................................................................... 9
9. European Authorised Representative.............................................................. 10
10. EMC-Declaration of conformity................................................................... 10
11. Statement ...................................................................................................... 13

1
1. The installation and components of equipment
1.1 Instruction
Guilin Woodpecker Medical Instrument Co., Ltd. is a professional manufac-
turer in researching, developing and producing ultrasonic scalers. The product is
mainly used for teeth cleaning and also an indisensable equipment for teeth dise-
ase prevention and treatment.
The ultrasonic periodontal treatment device PT 3 has scaling, perio functions
with the following features:
a) Circular vibration orbit, scaling and polishing together.
b) Small vibrating amplitude, enjoy the painless treatment.
c) Titanium scaling tips, no injury to cementum.
d) Clinical solutions are applicable for automatic water supply mode, inclu-
ding
Hydrogen peroxide, sodium hypochlorite, chlorhexidine
e)LED Handpiece, LED mode and non-led mode available, better visibility.
f)Automatic frequency tracking ensures that the machine always works on
the best frequency and more steadily.
g) Digital control, easy operation and more ecient for scaling.
h)The silicon-cover can be autoclaved to high temperature 134°Cand high
pressure 0.22Mpa.
1.2 Components
1.2.1 The components of machine are listed in the packing list.
1.2.2 Product performance and structural composition
Periodontal treatment device PT 3 is composed of electro circuit, water way,
handpiece, periodontal treatment device tip and foot pedal.
1.2.3 Scope of application
Periodontal treatment device PT 3 is used for the dental calculus elimination.
1.3 The main technical specications
1.3.1 Technical specications of PT 3
a) Main unit input: 220-240V~ 50Hz/60Hz 150mA
b) Output primary tip vibration excursion: ≤60μm
c) Output half-excursion force: <2N
d) Output tip vibration frequency: 28kHz±3kHz
e) Output power: 3W to 20W
f) Main unit fuse: T0.5AL 250V
g) Water pressure: 0.01MPa to 0.5MPa
h) Weight of main unit: 2.0kg
i) Operating mode: Continuous operation
j) Type of protection against electric shock: class II equipment
k) Degree of protection against electric shock: Type BF applied part

2
l) Applied part of the equipment: handpiece and tip
m) Degree of protection against harmful ingress of water: Ordinary equip-
ment, the foot switch is drip-proof equipment (IPX1)
n) Degree of safety of application in the presence of a Flammable Anesthetic
Mixture with air, Oxygen or Nitrous Oxide: Equipment not suitable for being
used in the presence of a ammable anesthetic mixture with air, oxygen or nitrous
oxide.
1.4 Instruction of the main components
Instruction and component sketch map
1.4.1 Front of the main unit sketch map
Picture 1
1.4.2 Back of the main unit sketch map
Picture 2

3
1.4.3 Sketch map for connection of detachable handpiece. are showed in picture 3.
picture 3
1.4.4 Instruction of using wrench
Picture 4

4
2. Installation and adjustment
2.1 Operation
2.1.1 Open the packing box, make sure that all the parts and accessories are
complete according to the packing list, take the main unit out of the box, and put
it on the the stable plane facing to the operator.
2.1.2 Turn the water control knob to the max according to the picture direction,
Do not screw it over tight in case of damage. [ note 1]
2.1.3 Insert the plug of the foot switch to its socket. (see picture 2)
2.1.4 Fill the box with water or connect one end of the water pipe to the water
entrance, and the other end to the clean water source. (see picture 2)
2.1.5 Turn o the power switch and plug the power cord to socket
2.1.6 Turn on the power switch, the power indicator lighted and the machine
is ready for work. Touch panel is applied to this machine, water supply mode or
power can be adjusted by directly touching the water supply mode identication
or power indicator on the touch panel.
2.1.7 In the condition of normal working, the frequency of the tips is very high,
light touch and a certain to-and-fro motion will eliminate the tartar without ob-
vious heating, overexetion and overatay are forbidden.
2.1.8 Vibrating intensity: Adjust the vibrating intensity according to your need,
usually adjust to the middle grade, and adjust the vibrating during the clinical tre-
atment according to the patient's sensitivity and the rigidity of the tartar.
2.1.9 Step on the foot switch, the tip begins to vibrate, and the LED lamp on
the top of the handpiece shines. Release the foot switch, the LED lamp keep shi-
ning for 10 seconds.
2.1.10 Select dierent led mode according to clinical situation.
2.1.11 Water volume adjustment: Step on the foot switch, and the tip begins to
vibrate, then turn the water control switch to ne spray to cool down the handpie-
ce and clean the teeth.
2.1.12 The handpiece can be handled in the same gesture as a pen in hand.
2.1.13 Make sure not to make the end of the tip touch the teeth vertically, and
not use too much pressure when the tip touch the surface of the teeth, in order not
to hurt the teeth and the tip.
2.1.14 After nishing operation, keep the machine working for 30 seconds with
the water supply to clean the handpiece and the tip.
2.1.15 Unscrew the scaling tip and sterilize it.
Note: Don't screw the scaling tips when stepping on the foot switch, and the
machine is working.
3. Maintenance and sterilization
3.1 All the scaling tips ,Handpiece,wrench can be autoclaved.

5
3.1.1 Autoclaved under high temperature, pressure, time:
134°C, 2.0bar~2.3bar (0.20MPa~0.23MPa), 4min.
3.2 The tip and wrench can be cleaned by ultrasonic cleaner.
3.3 Troubles shotting
Fault Possible Solutions
The scaling tip doesn’t vibrate
and no water owing out
when stepping on the foot
switch.
The plug is in loose or
wrong contact.
Connect the power plug well.
The foot switch is in loose
contact.
Connect the switch well.
The fuse is broken. Change a new fuse.
The scaling tip doesn’t vibrate,
but there is waterowing out
when stepping on the foot
switch.
The scaling tip is in loose
contact. Screw it tightly (see picture 4)
The connector plug of the
handpiece with the circuit
board is in loose contact.
Contact with the local distributor
or manufacturer.
Malfunction of the
handpiece.
Contact with the local distributor
or manufacturer.
The scaling tip vibrates but
there is no spray come out
when stepping on the foot
switch.
The water control switch is
o.
Turn on the switch [note 1].
There is impurity in the
solenoid valve.
Contact with the local distributor
or manufacturer.
The water pipe is jammed. Clean water pipe by multi-
function syringe [note 2].
There is water ow out when
turn o the power.
There is impurity in the
solenoid valve.
Contact with the local distributor
or manufacturer.
The handpiece generates heat.
The amount of spouting
water is too little.
Turn the water control switch to
a higher grade [note 1].
The potentiometer is
broken.
Change a new one.

6
Fault Possible Solutions
The amount of spouting water
is too little.
The water control knob is
a low grade.
Turn the knob to a high grade
[note 1].
The water pressure is not
enough.
Enhance the water pressure.
The water pipe is jammed. Clean the water pipe by
multi-function syringe [note 2].
The vibration of the tip
becomes weak.
The tip hasn't been screwed
tightly or becomes loose
because of vibration.
Screw the scaling tip tightly
(picture 4).
The tip is damaged.[note 3] Change a new one.
The tip is damaged
[ note 3 ].
Change a new one.
The vibrating intensity control
knob is seized up.
The potentiometer is
damaged.
Contact with the local distributor
or our company.
If the troubles still can't be solved, please contact with the local distributors or
manufacturer.
3.4 Notice
[Note 1] The water control knob can adjust the water volume according to the
image.
[Note 2] To clean the water pipe with the multi-function syringe of the dental
unit ( see picture 4):
Picture 4
a) Snip the water pipe at a distance of 10cm to 20cm from the water entrance.
b) Turn on the power switch, get through to the power.
c) Connect the multi-function syringe of the dental unit to the water pipe.

7
d) Screw o the scaling tip or pull out the handpiece.
e) Step on the foot switch.
f) Turn on the switch of the multi-function syringe, press the air or water into
the water pipe to clean and eliminate the impurity.
[Note 3 ] If the scaling tip has been screwed on tightly and there is ne spray
too, the following phenomena show that the scaling tip is damaged:
a) The vibrating intensity and the pulverization degree become weak obviou-
sly.
b) During operating, there is some buzz when the scaling tip is working.
3.5 Cleaning mode
It is suggested to wash and disinfect the water pipe after scaling everyday.
The “Cleaning mode” can wash and disinfect the water pipe, reducing the
crystal substance and bacterias in water pipe.
Operation:
1.Put distilled water or mineral substance into water tank.
2.Press the automatically water supply button and outside water button at the
same time (1s) to start the “Cleaning mode” after buzzer beeps. The button of
automatic water supply mode would ashes and others buttons will go out.
3.Link the connector and the handpiece with the drainage device.
4.Step the pedal, the device would start self-cleaning. After that the pedal
could be loosen.
5.After cleaning for 30s, the device would stop self-cleaning. Or u can stop
by step the pedal again or press the automatic water supply button.
6.After cleaning, press the automatically water supply button and outside wa-
ter button at the same time (1s) to exit the “Cleaning mode” after buzzer beeps.
4. Precaution
4.1 Usage notice
4.1.1 Keep the periodontal treatment device clean before and after operation.
4.1.2 The scaling tip, wrench and handpiece must be sterilized before each
treatment.
4.1.3 Don't screw the scaling tip when stepping on the foot switch.
4.1.4 The scaling tip must be fastened. There must be ne spray coming out
from the tip when operating.
4.1.5 Change a new one when the tip is damaged or worn excessively.
4.1.6 Don't twist or rub the tip.
4.1.7 While periodontal treatment device works, the heat of scaling tip will
become higher if there is no water owing out, please keep the water ow smoo-
thly.
4.1.8 Don’t use impure water source, please use pure water source, and nor-
mal brine can be used.

8
4.1.9 If use the water source without hydraulic pressure, the water surface
should be one meter higher than the head of the patient.
4.1.10 Don't knock or rub the handpiece.
4.1.11 Please put the power plug into the socket and make it easy to pull out, to
make sure it can be pulled out in emergency.
4.1.12 When using the equipment, please keep the water get through smoothly,
otherwise patient's tooth surface would be injured by overheat in the handpiece.
4.1.13 After operating, turn o electrical source, and then pull out the plug.
4.1.14 As a professional manufacturer of medical instruments, we are only res-
ponsible for the safety on the following conditions:
I. The maintenance, repair and modication are made by the manufacturer or
the authorized dealer.
II. The changed components are original of "WOODPECKER" and operated
correctly according to instruction manual.
4.1.15 The screw thread of the scaling tips produced by other manufacturers
maybe coarse, rusty and collapsed, which will damage the screw thread of the han-
dpiece irretrievably. Please use "WOODPECKER" brand scaling tip.
4.1.16 Please select a suitable power when using dierent type of tips.
4.2 Contraindication
4.2.1 The patient who has hemophilia is not allowed to use this equipment.
4.2.2 The patient or doctor who with heart pacemaker is forbidden to use this
equipment.
4.2.3 The heart disease patient, pregnant woman and children should be cau-
tious to use the equipment.
4.3 Storage and maintenance
4.3.1 The equipment should be handled carefully and lightly. Be sure that it is
far from the vibration, and is installed or kept in a cool, dry and ventilated place.
4.3.2 Don't store the machine together with the articles that are combustible
poisonous, caustic, or explosive.
4.3.3 This equipment should be stored in a room where the relative humidity is
10% ~ 93%, atmospheric pressure is 70kPa to106kPa, and the temperature is -20℃
~ +55℃.
4.3.4 Please turn o the power switch and pull out the power plug when the
equipment is not used. If the machine is not used for a long time, please make it get
through to the power and water once per month for ve minutes.
4.4 Transportation
4.4.1 Excessive impact and shake should be prevented in transportation. Lay it
carefully and lightly and don't invert it.
4.4.2 Don't put it together with dangerous goods during transportation.
4.4.3 Avoid solarization and getting wet in rain or snow during transportation.
4.5 Working condition

9
4.5.1 Environment temperature: +5°C to +40°C
4.5.2 Relative humidity: 30% ～75%
4.5.3 Atmosphere pressure: 70kPa to 106kPa
4.5.4 A temperature of the water at the inlet：not higher than +25°C
5. After service
We oer one year free repair to the equipment according to the warranty card.
The repair of the equipment should be carried out by professional technician. We
are not responsible for any irretrievable damage caused by the not professional per-
son.
6. Environmental protection
Please dispose according to the local laws.
7. Manufacturer’s right
We reserve the rights to change the design of the equipment, the technique, t-
tings, the instruction manual and the content of the original packing list at any time
without notice. If there are some dierences between blueprint and real equipment,
take the real equipment as the norm.
8. Symbol instruction
Trademark Consult the accompanying
documents
Anti-drip device Ordinary equipment
Alternating current Foot switch interface
Date of manufacture Manufacturer
Class II equipment Type BF applied part
serial number Used indoor only
Adjustment for the water
ow
Appliance compliance WEEE
directive
Water entrance pressure
0.01MPa - 0.5MPa Keep dry
Handle with care Recovery

10
CE marked product Earth (ground)
Can be autoclaved Mode of outside-water
system
Switch of automatic water
supply Mode of LED
Adjustment for the water ow, in Mode of auto-water system
Humidity limitation for
storage
Temperature limitation for
storage
Atmospheric pressure for storage
Authorised Representative in the EUROPEAN COMMUNITY
9. European Authorised Representative
10. EMC-Declaration of conformity

11

12

13
The device has been tested and homologated in accordance with EN 60601-
1-2 for EMC. This does not guarantee in any way that this device will not be
eected by electromagnetic interference Avoid using the device in high electro-
magnetic environment.
11. Statement
All rights of modifying the product are reserved to the manufacturer without
further notice. The pictures are only for reference. The nal interpretation rights
belong to GUILIN WOODPECKER MEDICAL INSTRUMENT CO., LTD. The
industrial design, inner structure, etc, have claimed for several patents by WOO-
DPECKER, any copy or fake product must take legal responsibilities.

ZMN/WI-09-205 V1.7-20180913