Woods Alitec A Series User manual

OPERATOR'S MANUAL
MCPSSAMH
SKID STEER
COLD PLANER
“A” Series
Manual Hydraulic
CP16AMH CP16AMHXT CP16AMHXTP
CP18AMH CP18AMHXT CP18AMHXTP
CP24AMH CP24AMHXT CP24AMHXTP
CP30AMH CP30AMHXT CP30AMHXTP
CP36AMH CP36AMHXT CP36AMHXTP
Effective Serial Numbers:
CP16AMH 6800020403
CP16AMHXT 6800010403
CP18AMH 7000010403
CP24AMH 7100010403
CP24AMHXT 7100020503
Rev. 7/4/2008
Tested. Proven. Unbeatable.

2 Introduction
CE Construction (Rev. 7/20/2007)
TO THE DEALER:
Assembly and proper installation of this product is the responsibility of the Woods®dealer. Read manual instructions
and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual
are completed before releasing equipment to the owner.
The dealer must complete the Product Registration included with the Operator’s Manual. The customer must sign the
registration which certifies that all Dealer Check List items have been completed. The dealer is to return the prepaid
postage portion to Woods, give one copy to the customer, and retain one copy. Failure to complete and return this
card does not diminish customer’s warranty rights.
TO THE OWNER:
Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and
safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become
acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be
obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in
the United States and Canada call 1-800-848-3447.
The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.
For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary
tools and equipment to handle all your needs.
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for
safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces
provided:
Model:_______________________________ Date of Purchase: _____________________
Serial Number: (see Safety Decal section for location) ____________________________________
Provide this information to your dealer to obtain correct repair parts.
Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.
The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with
an exclamation mark) to indicate the degree of hazard for items of personal safety.

Introduction 3
MCPSSAMH (Rev. 8/25/2006)
TABLE OF CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SAFETY DECALS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
SERVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
BOLT SIZE CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
FITTING TORQUE CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PRODUCT WARRANTY. . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . .BACK COVER
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your planer. Read it carefully. It fur-
nishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience and
these instructions, you should be able to develop proce-
dures suitable to your particular situation.
The illustrations and data used in this manual were cur-
rent at the time of printing but, due to possible inline
production changes, your planer may vary slightly in
detail. We reserve the right to redesign and change the
planer as may be necessary without notification.
Throughout this manual, references are made to right
and left direction These are determined by standing
behind the planer facing the direction of forward travel.

4 Introduction
MCPSSAMH (Rev. 8/25/2006)
“A” SERIES SPECIFICATIONS
CP16ATD CP18ATD CP20ATD CP24ATD CP30ATD CP36ATD
Planing Width 16 inches 18 inches 20 inches 24 inches 30 inches 36 inches
Planing Depth 0 - 6 inches 0 - 6 inches 0 - 6 inches 0 - 6 inches 0 - 6 inches 0 - 6 inches
Hydraulic Required 30 - 60 HP 30 - 60 HP 30 - 60 HP 30 - 60 HP 30 - 60 HP 30 - 60 HP
Sideshift Capacity 22 inches 22 inches 22 inches 22 inches 22 inches 22 inches
Number of Carbide Picks 50 56 (or 84) 62 70 77 99
Tilt Capability ±15° ±15° ±14° ±12° ±11° ±9°
Hydraulic Flow Required 25 - 31 gpm 25 - 31 gpm 25 - 31 gpm 25 - 31 gpm 25 - 31 gpm 25 - 42 gpm
Hydraulic Pressure
Required PSI 2000 - 3500 2000 - 3500 2000 - 3500 2000 - 3500 2000 - 3500 2500 - 5000
Operating Weight 1750 lbs 2000 lbs 2100 lbs 2300 lbs 2450 lbs 2600 lbs
Planetary Gearbox Capacity 25 oz 25 oz 25 oz 25 oz 25 oz 25 oz
Planetary Lubrication 80 - 90W GL5 Gear Lube
“XT” SERIES SPECIFICATIONS
CP16ATDXT CP18ATDXT CP20ATDXT CP24ATDXT CP30ATDXT
Planing Width 16 inches 18 inches 20 inches 24 inches 30 inches
Planing Depth 0 - 6 inches 0 - 6 inches 0 - 6 inches 0 - 6 inches 0 - 6 inches
Hydraulic Required 30 - 60 HP 30 - 60 HP 30 - 60 HP 30 - 60 HP 30 - 60 HP
Sideshift Capacity 22 inches 22 inches 22 inches 22 inches 22 inches
Number of Carbide Picks 50 56 62 70 77
Tilt Capability ±15° ±15° ±14° ±12° ±11°
Hydraulic Flow Required 25 - 42gpm 25 - 42 gpm 25 - 42 gpm 25 - 42 gpm 25 - 42 gpm
Hydraulic Pressure
Required PSI 2000 - 5000 2000 - 5000 2000 - 5000 2000 - 5000 2000 - 5000
Operating Weight 1750 lbs 2000 lbs 2100 lbs 2300 lbs 2450 lbs
Planetary Gearbox Capacity 25 oz 25 oz 25 oz 25 oz 25 oz
Planetary Lubrication 80 - 90W GL5 Gear Lube

Safety 5
Alitec CP (Rev. 7/7/2006)
INSTALLATION
Hydraulics must be connected as instructed in
this manual. Do not substitute parts, modify, or
connect in any other way.
After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
TRAINING
Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
the Dealer Locator at www.WoodsEquipment.com,
or in the United States and Canada call 1-800-848-
3447.) Failure to follow instructions or safety rules
can result in serious injury or death.
If you do not understand any part of this manual
and need assistance, see your dealer.
Know your controls and how to stop engine and
attachment quickly in an emergency.
Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instruc-
tions.
Keep hands and body away from pressurized
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
Never allow children or untrained persons to
operate equipment.
PREPARATION
Check that all hardware is properly installed.
Always tighten to torque chart specifications
unless instructed otherwise in this manual.
Counterweight ballast may be required for
machine stability. Check your power unit manual or
contact your dealer.
Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
After connecting hoses, check that all control
lever positions function as instructed in the Opera-
tor's Manual. Do not put into service until control
lever and equipment movements are correct.
Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifica-
tions and may be dangerous.
Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
Safety is a primary concern in the design and
manufacture of our products. Unfortunately, our
efforts to provide safe equipment can be wiped
out by an operator’s single careless act.
In addition to the design and configuration of
equipment, hazard control and accident preven-
tion are dependent upon the awareness, concern,
judgement, and proper training of personnel
involved in the operation, transport, maintenance
and storage of equipment.
It has been said “The best safety device is an
informed, careful operator.” We ask you to be that
kind of operator.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

6 Safety
Alitec CP (Rev. 7/7/2006)
Be sure attachment is properly secured,
adjusted, and in good operating condition. Coupler
lockpins must be fully extended and properly
engaged into attachment retaining slots.
Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
Make sure shields and guards are properly
installed and in good condition. Replace if dam-
aged.
Inspect and clear area of stones, branches, or
other hard objects that might be thrown, causing
injury or damage.
OPERATION
Improper operation can cause the machine to
tip or roll over and cause injury or death.
• Keep power unit lift arms and attachment as
low as possible.
• Do not travel or turn with power unit lift arms
and attachment raised.
• Turn only on level ground.
• Go up and down slopes, not across them.
• Keep the heavy end of the machine uphill.
• Do not overload the machine.
Never use attachment to carry loads that exceed
the rated operating capacity or other specifications
of the power unit. Check your power unit manual or
see your dealer for rated operating capacity.
Exceeding this capacity can cause machine to tip,
roll over, or present other hazards that can cause
injury or death.
Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
Contact with high voltage, overhead power
lines, underground cables, gas lines, and other
hazards can cause serious injury or death from
electrocution, explosion, or fire.
Keep bystanders away from equipment.
Never direct discharge toward people, animals,
or property.
Do not operate or transport equipment while
under the influence of alcohol or drugs.
Operate only in daylight or good artificial light.
Keep hands, feet, hair, and clothing away from
equipment while engine is running. Stay clear of all
moving parts.
Always comply with all state and local lighting
and marking requirements.
Do not allow riders. Do not lift or carry anybody
on the power unit or attachments.
Always sit in power unit seat when operating
controls or starting engine. Securely fasten seat
belt/operator restraint, place transmission in park
or neutral, engage brake and ensure all other con-
trols are disengaged before starting power unit
engine.
Look down and to the rear and make sure area
is clear before operating in reverse.
Use extreme care when working close to fences,
ditches, other obstructions, or on hillsides.
Do not operate or transport on steep slopes.
Do not stop, start, or change directions sud-
denly on slopes.
Use extreme care and reduce ground speed on
slopes and rough terrain.
Watch for hidden hazards on the terrain during
operation.
Stop power unit and implement immediately
upon striking an obstruction. Dismount power unit,
using proper procedure. Inspect and repair any
damage before resuming operation.
Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
Before making any adjustments on attachment,
stop engine and engage parking brake. Never
adjust or work on attachment while the power unit
or attachment is running.
Before leaving operator's seat, lower lift arms
and put attachment on the ground. Engage brake,
stop engine, remove key, and remove seat belt.
MAINTENANCE
Before leaving operator's seat, lower lift arms
and put attachment on the ground. Engage brake,
stop engine, remove key, and remove seat belt.
NEVER GO UNDERNEATH EQUIPMENT. Never
place any part of the body underneath equipment
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety 7
Alitec CP (Rev. 7/7/2006)
or between moveable parts even when the engine
has been turned off. Hydraulic system leak-down,
hydraulic system failures, mechanical failures, or
movement of control levers can cause equipment
to drop or rotate unexpectedly and cause severe
injury or death.
• Service work does not require going under-
neath.
• Read Operator's Manual for service instruc-
tions or have service performed by a qualified
dealer.
Do not modify or alter or permit anyone else to
modify or alter the equipment or any of its compo-
nents in any way.
Your dealer can supply original equipment
hydraulic accessories and repair parts. Substitute
parts may not meet original equipment specifica-
tions and may be dangerous.
When removing front wheel pins, be sure to
support the front of the depth skid to prevent
hands or feet from being crushed.
Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
Do not allow bystanders in the area when oper-
ating, attaching, removing, assembling, or servic-
ing equipment.
Be sure attachment is properly secured,
adjusted, and in good operating condition. Coupler
lockpins must be fully extended and properly
engaged into attachment retaining slots.
Never perform service or maintenance with
engine running.
Keep all persons away from operator control
area while performing adjustments, service, or
maintenance.
Tighten all bolts, nuts, and screws to torque
chart specifications. Check that all cotter pins are
installed securely to ensure equipment is in a safe
condition before putting unit into service.
Make sure all safety decals are installed.
Replace if damaged. (See Safety Decals section for
location.)
Make sure shields and guards are properly
installed and in good condition. Replace if dam-
aged.
Do not disconnect hydraulic lines until all sys-
tem pressure is relieved. Lower unit to ground,
stop engine, and operate all hydraulic control
levers.
Leak down or failure of mechanical or hydraulic
system can cause equipment to drop.
STORAGE
Follow manual instructions for storage.
Keep children and bystanders away from stor-
age area.
SAFETY RULES
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!


8 Safety
MCPSSAMH (Rev. 8/25/2006)
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
WARNING
PINCH AREA
Keep clear during
operation.
D0192
WARNING
FLYING OBJECT
HAZARD
Keep clear during
operation.
D0195
WARNING
FLYING OBJECT
HAZARD
Keep clear during
operation.
D0195
TO AVOID SERIOUS INJURY OR DEATH:
nRead operator's manual and power unit manual before operating,
servicing, or repairingattachment. Follow all safety rules and
instructions. (Manuals are available from dealer or, in the United
States and Canada, call 1-800-790-0557.)
nOnly operate from operator's seat with seat belt/operator restraint
securely fastened.
nBefore leavingoperator's seat: follow power unit manual
instructions, lower lift arms and attachment to ground, stop engine,
remove key, engage brake, and remove seat belt/operator restraint.
nAllow no children or untrained persons to operate equipment.
WARNING
D0404-A
WARNING
ROTATING CUTTER
Keep clear during operation.
See Operator's Manual
for maintenance precautions.
D0193
D0195
SERIAL NUMBER PLATE D0193
D0404
19924 D0192
HIGH-PRESSURE HYDRAULIC OIL LEAKS CAN PENETRATE SKIN
RESULTING IN SERIOUS INJURY, GANGRENE OR DEATH.
n Check for leaks with cardboard; never use hand.
n Before loosening fittings: lower load, release pressure, and
be sure oil is cool.
n Consult physician immediately if skin penetration occurs.
WARNING
19924-B
MODEL NO. SERIAL NO.
Woods Equipment Company
Oregon, Illinois, U.S.A.

Safety 9
MCPSSAMH (Rev. 8/25/2006)
SAFETY & INSTRUCTIONAL DECALS
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged!
WARNING
FALLING OFF CAN RESULT IN BEING RUN OVER.
 Skid steer must have ROPS and seat belt/operator restraint.
Keep seat belt/operator restraint securely fastened.
Allow no riders.
RAISED EQUIPMENT CAN DROP AND CRUSH.
Never go underneath raised equipment or raised Skid Steer lift
arms, which can drop from hydraulic leak down, hydraulic
system failures, movement of control levers or mechanical
linkage failures.
Service work does not require going underneath equipment.
Read manual instructions.
FALLING OFF OR GOING UNDERNEATH EQUIPMENT
CAN RESULT IN SERIOUS INJURY OR DEATH. 54519--A
54519
CAUTION
CRUSHING HAZARD
Do not raise or roll back the lift
arms when the valve arm is
lowered into the cab.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY.
D0438
D0445
D0438
BE CAREFUL!
Use a clean, damp cloth to clean safety
decals.
Avoid spraying too close to decals when
using a pressure washer; high-pressure
water can enter through very small
scratches or under edges of decals
causing them to peel or come off.
Replacement safety decals can be
ordered free from your Woods dealer. To
locate your nearest dealer, check the
Dealer Locator at
www.WoodsEquipment.com, or in the
United States and Canada call
1-800-319-6637.
See Parts section for decal location.

10 Operation
MCPSSAMH (Rev. 8/25/2006)
OPERATION
Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer.) Failure to follow instructions or safety
rules can result in serious injury or death.
Power unit must be equipped with ROPS and
seat belt/operator restraint. Keep seat belt/operator
restraint securely fastened/engaged. Falling off
power unit can result in death from being run over
or crushed. Keep ROPS systems in place at all
times.
 Operators must be instructed in and be capable
of the safe operation of the equipment, its attach-
ments, and all controls. Do not allow anyone to
operate this equipment without proper instructions.
NOTICE
■ Skid steers must be equipped with an auxiliary
hydraulic system capable of supplying continuous
flow for hydraulic motor operation.
The planer attachment is hydraulic powered and
intended for use in milling asphalt or concrete surfaces.
The performance of the attachment can vary greatly
depending upon how it is used and operated. There-
fore, the recommended operating procedures con-
tained within this manual should be followed at all times
for maximum productivity.
PRE-OPERATION CHECK LIST
(OWNER'S RESPONSIBILITY)
___ Review and follow all safety rules and safety
decal instructions on page 5 through page 9.
___ Check that all safety decals are installed and in
good condition. Replace if damaged.
___ Check that all shields and guards are properly
installed and in good condition. Replace if
damaged.
___ Check that equipment is properly and securely
attached to skid steer.
___ Check that all hardware and cotter pins are
properly installed and secured.
___ Do not allow riders. Keep all bystanders away
from equipment working area.
___ Check all lubrication points and grease as
instructed. See page 16.
___ Check that all hydraulic hoses and fittings are
in good condition and not leaking before start-
ing skid steer.
___ Check that hoses are not twisted, bent sharply,
kinked, frayed or pulled tight. Replace any
damaged hoses immediately.
___ Make sure skid steer ROPS and seat belt are
in good condition. Keep seat belt securely fas-
tened during operation.
ATTACHING PLANER
1. Place the coupler pins in the disengaged position
as shown in Figure 1.
2. Rotate the skid steer attach slightly forward.
Figure 1.
3. Fully lower the lift arms (2) as shown in Figure 2.
4. Pull forward to the planer. Make sure the outside of
the skid steer attach (1) is aligned with the inside of
the planer attach (2).
5. Continue to pull forward until the skid steer attach
makes contact with the planer attach.
6. Raise the skid steer arms until the top of the skid
steer attach contacts the top latch bar (3) on the
attachment.
WARNING
DP1
(Rev. 7/4/2008)

Operation 11
MCPSSAMH (Rev. 8/25/2006)
Figure 2.
7. Roll the skid steer arms back until the planer is
completely off the ground as shown in Figure 3.
8. Engage the parking brake on the skid steer.
9. Stop the engine and remove ignition key.
NOTE: When using a quick attachment hookup to
the skid steer the locking pins on the loader arms
should always be engaged and secured.
Figure 3.
ATTACHING HOSES
Relieve the back pressure in the auxiliary hydraulic
system and move the coupler pins to the engaged
position.
The planer requires a minimum hydraulic supply of 25
gallons per minute (90 liters per minute) at 2000 psi.
NOTICE
■ Insufficient hydraulic power will result in poor
performance.
In attaching the planer to the skid steer, ensure that all
hydraulic hoses are coupled securely to the quick cou-
plers.
NOTICE
■ JI Case, Gehl, Trak, and Thomas have 5 hoses
(motor pressure, return, casedrain, and two auxil-
iary).
■ Ford and New Holland have 3 hoses (motor
pressure, return, and casedrain).
■ Casedrain must be attached and hose pressure
must not exceed 15 psi. Motor seal failure will
occur if the casedrain is not attached, if a hose is
crimped, or if hose pressure is excessive. All
hoses should be free of kinks, cuts, or abrasions
for safe operation.
ADJUSTING THE VALVE ARM
■ Keep hands and feet away from the valve arm
pivot to prevent hands or feet from being crushed
when the arm is lowered.
All non-electro-hydraulic cold planers are equipped
with an adjustable valve arm. The following procedure
should be followed to properly adjust the valve arm.
1. Carefully lower the valve arm into the cab.
2. Check the valve height. If the valve needs to be
raised or lowered, return the valve arm to the
stored position as shown in Figure 4.
3. Remove the pivot stop (1) and move to the desired
location. Placement in the top rear hole allows
minimum positioning in the cab. The placement in
the bottom of the rear hole allows maximum
positioning in the cab.
4. Carefully lower the valve arm into the cab.
5. If the desired location is not achieved, repeat step
2 and 3.
6. Check the valve front-to-back position. If the valve
needs to be moved in or out, remove slide stop pin.
■ Make sure the valve is supported while the
slide stop pin is removed so the valve is prevented
from swinging downward.
7. Slide the valve arm to the desired position and
reinstall the slide stop pin.
3
21
DP3
ACAUTION
ACAUTION
(Rev. 7/4/2008)

12 Operation
MCPSSAMH (Rev. 8/25/2006)
Figure 4.
MANUAL VALVE COLD PLANERS
The manual valve (non-electro-hydraulic) cold planers
utilize a three-function valve stack to control both direc-
tion and function. Figure 5 shows the position and func-
tion of the three levers.
Figure 5.
■ Do not raise or roll back the lift arms when the
valve arm is lowered into the cab. Failure to follow
these instructions could result in serious injury.
HYDRAULIC DEPTH CONTROL
To operate the hydraulic depth control, set the options
toggle switch to “depth” and actuate the auxiliary circuit
to achieve the desired depth.
HYDRAULIC TILT
To operate the hydraulic tilt, set the options toggle
switch located at the operator’s control panel to “tilt”,
and actuate the auxiliary circuit.
SIDESHIFT ADJUSTMENT
1. Raise the planer 6" to 8" off the ground.
2. Engage the parking brake on the skid steer.
3. Stop the engine.
4. The planer can be shifted side-to-side using the
sideshift function. The two sideshift hoses when
connected to the auxiliary hydraulics of the skid
steer, provide hydraulic power necessary for
sideshift operation. By actuating the auxiliary
circuit, the planer will shift on the sideshift rod.
PLANER OPERATION
■ Never open the top cover used for drum access
during operation. The two cover latches (see parts
section) should be checked to make sure they are
securely fastened before beginning operation.
To operate the cold planer, lower the valve arm into the
cab.
NOTICE
■ When the valve arm is lowered into the cab, do
not raise the lift arms excessively. The valve may
interfere with the cab causing damage to the skid
steer or the cold planer.
Activate the auxiliary hydraulics. Be sure the drum is
rotating counter-clockwise direction if viewed from the
motor side of the cold planer.
When engaging the hydraulic power to the attachment,
the drum should not be in contact with the surface to be
1
DP20
ACAUTION
WARNING
(Rev. 7/4/2008)

Operation 13
MCPSSAMH (Rev. 8/25/2006)
planed. Free rotation is required to prevent excessive
pressure spikes upon startup. As is always the case,
the operator must always be seated in the skid steer
upon startup.
Engage the hydraulic power and lower the planer
slowly. Actuate the bucket cylinder function for rollout
until the planer wheels come in contact with the planing
surface when set to the desired depth. Before advanc-
ing the hose vehicle, allow the planer to operate until it
reaches the desired planing depth.
NOTICE
■ For proper operation, the majority of the weight
of the front of the skid steer should be placed upon
the planer with the loader arms fully lowered. The
transfer of skid steer weight to the attachment
results in smoother, faster planing. The loader
arms should never be placed in the float condition;
because, excessive vibration will result.
With the rear gauge wheels set for acceptable planing
depth, the bucket function should be used for lifting or
lowering during operation.
The drum rotation will stall when the load on the planer
is too high. This is most likely the result of excessive
ground speed. The hydraulic reliefs on board the skid
steer are designed to prevent damage to the hydraulic
system by diverting all flow from the planer motor. If
this occurs, stop or slightly reverse the forward drive of
the skid steer and slowly move forward.
NOTICE
■ The bucket cylinder function should never be
used to stop operation due to the existence of sec-
ondary reliefs on some skid steer bucket cylinder.
For maximum productivity, the planer should always be
operated at full engine throttle to ensure that full
hydraulic horsepower is available to the cutting drum.
TRANSPORTING
Avoid excessive ground speed and sudden maneu-
vers.
1. Center the cold planer in front of the skid steer.
2. Return the valve arm to the stored position. See
Figure 6.
3. Roll the skid steer arms fully back and raise the
planer 12" to 15" off the ground. Avoid excessive
ground speed and sudden maneuvers.
NOTICE
■ When transporting attachment make sure the
drum does not contact ground as this may cause
the drum to turn resulting in damage to the motor.
Figure 6.
CLEANING
After Each Use
●Remove large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●Inspect machine and replace worn or damaged
parts.
●Replace any safety decals that are missing or not
readable.
Periodically or Before Extended Storage
●Clean large debris such as clumps of dirt, grass,
crop residue, etc. from machine.
●Remove the remainder using a low-pressure water
spray.
1. Be careful when spraying near scratched or torn
safety decals or near edges of decals as water
spray can peel decal off surface.
2. Be careful when spraying near chipped or
scratched paint as water spray can lift paint.
3. If a pressure washer is used, follow the advice
of the pressure washer manufacturer.
●Inspect machine and replace worn or damaged
parts.
●Sand down scratches and the edges of areas of
missing paint and coat with Woods spray paint of
matching color (purchase from your Woods
dealer).
●Replace any safety decals that are missing or not
readable (supplied free by your Woods dealer).
See Safety Decals section for location drawing.
(Rev. 7/4/2008)

14 Service
MCPSSAMH (Rev. 8/25/2006)
SERVICE
Proper maintenance of the planer will result in longer
life and the most productive and cost effective opera-
tion.
SIDESHIFT CYLINDER REMOVAL
Before leaving operator's seat, lower lift arms
and put attachment on the ground. Engage brake,
stop engine, remove key, and remove seat belt.
With the attachment on a level surface, remove all
three one inch retaining rings from cylinder mount-
ing pins.
Pull the cylinder evenly from both mounting pins.
Remove the pin on the left-hand side and slide the
rod end off the back plate.
NOTICE
■ Remove any residual pressure in the cylinder
by cycling the loader auxiliary control from side to
side with the skid steer engine off.
With the attachment on a level surface, remove all
three 1" retaining rings from cylinder mounting pins.
Pull the cylinder evenly from both mounting pins.
Remove the pins on the left-hand side and slide the rod
end off the backplate.
PLANETARY REMOVAL
1. Remove the drum from the planer as described in
Drum Removal on page 14.
2. Fully support the planetary with hoist and remove
the planetary flange mounting nuts.
3. Slide the planetary from the drum with a hoist or
similar device rated for more than 250 lbs capacity
(550 kg).
SIDESHIFT FRAME REMOVAL
1. Disconnect the drive motor hoses.
2. Remove sideshift cylinder as described in Sideshift
Cylinder Removal on page 14.
3. Remove three backplate clamp nuts and bolts and
main pivot retaining ring.
4. Attach the planer to the skid steer and slowly
separate the sideshift from the chassis.
DRUM REMOVAL
1. With the attachment resting on a hard, flat surface,
loosen the two set screws which fix the inner
bearing race to the dead shaft.
2. Remove the dead shaft by removing the three bolts
and nuts and pulling the dead shaft from the
bearing and out of the planer head.
3. Remove the drive motor assembly by removing the
two mounting bolts.
4. Remove the planetary mounting bolts.
5. Return to the skid steer operator’s seat and check
to see that all personnel are clear of the working
area. Insert the key in the ignition and start the skid
steer.
6. Sideshift the planer head slightly to the left (from
the operator’s viewpoint) to remove the planetary
pilot from the planer head.
7. Raise the attachment with the skid steer and the
drum should remain on the floor.
8. Shut the engine off and remove the ignition key.
■ If drum does not remain on the floor, lower the
planer, shut the engine off, remove the ignition key
and review steps one through four. Do not attempt
to dislodge the drum while the planer frame is in
the raised position. Never place hands or any part
of your body in, around, or under the drum as it
may fall causing serious injury.
■ Use extreme caution during this operation to
prevent planetary from tipping and falling.
MOTOR REMOVAL
1. Remove and cap the motor hoses as shown in
Figure 7.
AWARNING
AWARNING
(Rev. 7/4/2008)

Service 15
MCPSSAMH (Rev. 8/25/2006)
Figure 7.
2. Remove 1/4" cross bolt as shown in Figure 8.
Figure 8.
3. Remove four 3/8" motor bolts.
4. Remove the motor.
BEARING REMOVAL
1. Perform steps one through four of Motor Removal.
2. Loosen the bearing set of screws.
Figure 9
3. Slide shaft towards the motor side of the attach
frame until the bearing side coupler clears the
bearing.
4. Remove two 1/2" bolts.
ACME SCREW REPLACEMENT
1. Perform steps one through four of Motor Removal
and steps two though four of Bearing Removal.
2. Remove 1/4" bolts as shown in Figure 10.
Figure 10.
3. Slide couplers off the acme screw.
4. Manually turn the acme screw to back it out of the
bearing side of the sideshift frame.

16 Service
MCPSSAMH (Rev. 8/25/2006)
ACME NUT REPLACEMENT
1. Perform steps one through three of Acme Screw
Replacement.
2. Remove three 3/8" bolts.
3. Place the nut flange in a vice and use a pipe
wrench to remove the nut from the flange.
PICK / HOLDER REPLACEMENT
As regular use takes place, normal wear of the carbide
picks will occur with the outer most picks wearing first.
The pick tool included with the planer should be used
to remove the picks from the cast holders. In the event
the pick tool is not available, any hardened punch or
tool allowing access to the bottom of the holders can
be used.
NOTICE
■ Welder must be grounded directly to drum dur-
ing pick holder replacement or severe bearing
damage will result.
■ Never drive the pick in by striking it directly on
the end as this can cause the pick to chip and
cause injury or create small stress fractures in the
pick resulting in premature wear.
A length of pipe with a 3/4 - 1 inch inside diameter can
be placed over the pick to protect it from direct hit.
Striking a small piece of wood placed on the pick to
absorb the shock will prevent damage.
■ Always wear safety glasses when performing
this operation. Hardened tools and picks can shat-
ter causing injury.
The factory installed carbide pick chosen for use is a
general purpose asphalt / concrete pick as the cold
planer is designed for both asphalt and concrete plan-
ing applications. For replacement of multi-purpose
picks always specify Alitec B1050S picks from your
local dealer. If the planer is to be used specifically for
concrete, a special concrete pick is available. Specify
B1050C.
NOTICE
■ To prevent the picks from seizing in the hold-
ers, the picks should be sprayed with diesel fuel at
the end of each day. This will break down the
asphalt build-up in the holders and prevent prema-
ture wear by allowing the picks to rotate in the
holders. Excess diesel fuel should be caught in a
collection pan and properly disposed. If the pick
remains in the holder beyond its intended replace-
ment point, it reduces the cutting performance and
will not protect the holder.
■ For proper operation, the picks should be
checked at least every two hours and lubricated
daily to ensure that they can freely rotate in their
holders.
LUBRICATION
Lubricate the grease points daily on all planer wheels
as well as the drum bearings.
The lubricant in the gear case of the planetary must be
changed within the first 50 hours of operation. After
that, the lubricant need only be changed once per year
or every 1000 hours whichever occurs first.
NOTICE
■ Type of lubricant should be 80 - 90W gear lube,
with an EP (extreme pressure) rating of GL-5 mini-
mum. Thirty-one (31) ounces (CP16 - 30ATD XT =
19 ounces) is the amount required for each change.
The lubricant can be changed by removing the drain
plug located on the planetary gear box flange between
the chassis and the drum. Rotate the drum until the
plug is at its lowest position and remove the plug. (It
may be necessary to temporarily remove the drive
motor to allow the drum to rotate.) Allow lubricant to
drain. Rotate drum until the drain hole is aligned with
the inspection hole in the side of the chassis. Refill
gear case with thirty-one ounces (CP16 - 30ATD XT =
19 ounces) EP-90 gear lubricant. Reinstall drain plug.
Reinstall drive motor if it was removed.
AWARNING
AWARNING
(Rev. 7/4/2008)

Troubleshooting 17
MCPSSAMHS (Rev. 8/25/2006)
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSES CHECK THE FOLLOWING
Planer loses power. Relief setting in auxiliary system lower
than standard 2400 psi. Remove and clean or replace solenoid cartridge or replace O-rings. Check
reliefs in the following sequence -
loader valve, standard auxiliary valve.
Reset or replace any relief below 2200
psi. The flow should be no less than 25
gpm. If pump output is 20% less than
rated pump specifications, the pump
may require repair. Consult loader ser-
vice manual.
Loader circuit pump or auxiliary pump
failure.
Tilt function is jumpy and
erratic. Tilt clamp bolts set too tight or rusted plate. Loosen tilt clamp bolts to provide .015 clearance or grease between plates.
Planer drive motor leaks
at shaft seal. Excess motor case drain pressure. The maximum case drain pressure allowed is 25 psi at full engine throttle.
Replace shaft seal.
No functions work. No power to controller. Check fuse and power lead connec-
tions.
One function doesn’t
work. Check power to coil. If coil has power and pulls, cartridge is defective; replace cartridge. If coil
doesn’t pull check for power to coil or
replace coil.
Bearing failure of motor
or output bearing. Improper lubrication of bearing. Pick holder replacement-welder not
grounded through drum.
Re-grease outboard bearing each 4 - 8
hours. During holder replacement,
ground welder directly to drum. (See
Service section.)

18 Parts
MCPSSAMH (Rev. 8/25/2006)
CPAMH ASSEMBLY
69 68
87, 88, 89
20
18 31
91
21
22
14
100
677
76
28 20
35 66 33 32
63 37
17 39
36 34
83
41 17 40
42
64 65
38
53
85, 89
1
8
579
10
11 12
50
86, 89
7398
26 49
25
36
82 92 48 102 30 78 82
13
17 15 16
9
4
86, 89 87, 89 42
96
75 70
80
43
20 7244
45
59
57
87, 88, 89
90
19
62
67
20, 28
23
24
61 99
27
60
71
17
52
17
55
56
101
74
93 42, 51
89, 29
2, 89
95
3 81
67
89, 29
2, 89
84, 94 47
54
97
99 58
39
7, 46

Parts 19
MCPSSAMH (Rev. 8/25/2006)
CPAMH ASSEMBLY
REF PART QTY DESCRIPTION
1 ----- 1 Attach frame
2 976 7 HHCS 3/8 NC x 1-1/2 GR5 ZP
3 C2201 1 Cylinder, Hyd 2 x 22 without depth
4 104027 1 Pin, 1 x 6 x 5.25 S.R. HA10
5 M0003 13 Retaining ring, 1" external HD
6 F1407 3 Fitting, 6 OM x 6 SLM
7 F1387 2 Fitting, 6 SLF x 6 SLF 90 -or-
F1387 3 Fitting, 6 SLF x 6 SLF 90 (CP36 &
XT)
8 C0801 1 Cylinder, Hyd 1.5 x 8
9 101699 1 Backplate weld, CP16A pivot -or-
101700-1 1 Backplate weld, CP18A pivot -or-
101702 1 Backplate weld, CP24A pivot -or-
102978 1 Backplate weld, CP30A pivot -or-
105575 1 Backplate weld, CP36A pivot
10 100601 1 Bushing, 2 x 2.5 x 5/8 pivot
11 B3221 1 Washer, 2 flat GR 8 Plt Uss
12 M0042 1 Retaining ring, 2" Ext Plt
13 11854 3 HHCS 5/8 NC x 2-1/2 GR8 ZP
14 M0114 2 Zerk, grease 1/4 - 28 ST
15 BB044 2 Bushing, 1.00 x 1.25 x 2.44
16 21594 2 HHCS 1 NC x 4 GR8 ZP
17 B1021 14 Washer, 5/8 flat SAE Plt Hrd
18 100708 1 Skid asy, deadshaft side
19 100712 1 Skid asy, motor side CPA
20 57816 10 Washer 1/2 SAE flat Hrd
21 100604 4 Wheel asy, cast new design
22 101218 4 Bushing, wheel 1.03 x 1.25 x 3.7
23 B1609 2 Bolt, 1 x 7 - 8 GR5 Plt
24 34279 2 Lock nut 1 NC
25 101053 2 Depth cyl weld, hyd 1.5 x 12
26 101747 2 Plate, spacer skid CPA / MP 5/16
27 F1506 2 Fitting, 6 SLM x 6 SLF x 6 SLM
28 B0819 4 Bolt, 1/2 x 2-1/4 - 20 Plt GR8
29 B0618 17 Nut, 3/8 - 16 GR8 Stover lock
30 T1018-1 2 Pin, 1 x 5.62 S.R. 5.00
31 100709 2 Pin weld, 1 x 8.31 S.R. 7.8
32 102670416 1 Drum weld, CP16A 50 holders -or-
102670418 Drum weld, CP18A 56 holders -or-
102670424 Drum weld, CP24A 70 holders -or-
102670430 Drum weld, CP30A 85 holders -or-
102670436 Drum weld, CP36A 99 holders
33 P0313 1 Pick holder
34 1024801 A/R Pick, Asphalt kennamental RS01
B1050C A/R Pick, concrete
35 BB001 1 Bearing, 2.5" FYRP
36 B0816 8 Nut, 1/2 - 20 Stover Plt GR5
37 HC422 1 Planetary, Auburn 24.85:1 -or-
HC439 1 Planetary, Auburn MOD 7 15.88
-or-
HC440 1 Planetary, Auburn MOD 7 24.53
-or-
38 B0915 9 Nut, 9/16 - 18 GR5 Stover Plt
39 59019 5 HHCS 5/8 NC x 1-1/2 GR8 ZP
40 101979 1 Deadshaft weld, triangle CP
41 59001 3 HHCS 5/8 NC x 2.00 GR8 ZP
42 B1015 6 Nut, 5/8 - 11 Stover UNC GR5
43 HC412 1 Motor, Eaton 35 CC -or-
HC551 1 Motor, M44-13 Tooth Sauer-Dan
-or-
HC321 1 Motor, Sundstrand M35-3004
44 21666 2 HHCS 1/2 NC x 1-1/2 GR8 ZP
45 F1293 3 Fitting, 12 OM x 12 SLM 90 -or-
F1501 2 Fitting, 16 OM x 12 SLM 90
46 F1448 1 Fitting, 8 OM x 6 SLM ST -or-
F1465 1 Fitting, 10 OM x 6 SLM ST
47 HC553 1 Valve, stack Gresen w/PO check
-or-
HC554 1 Valve asy, Bondioli DN/3
48 106465 1 Chassis weld, CP16A -or-
106466 1 Chassis weld, CP18A -or-
106467 1 Chassis weld, CP24A -or-
106468 1 Chassis weld, CP30A -or-
106469 1 Chassis weld, CP36A
49 101478 2 Plate, spacer skid CPA/MP 1/2
50 101479 2 Plate, Retaining skid CPA / MP
51 B1020 3 Washer, 5/8 flat USS Plt Hrd
52 100913 1 Spring, hose support
53 F1139 1 Plug, 6 OM Fitting Sockethead
54 F1448 8 Fitting, 8 OM x 6 SLM ST
55 H1692 2 Hose 3/8 90 9/16 JICF 9/16 JICF
56 105697 1 Plate, sideshift cylinder adapter
57 H1627 1 Hose #12 x 110" 12 SLF x 12 SLF
R1
58 H1696 2 Hose #6 x 102" 6 SLF x 6 SLF R1
59 H1626 1 Hose #12 x 110" 12 SLF x 12 SLF
5000P
60 H1695 2 Hose 3/8 66 11/16 off 11/16 off
61 H1609 2 Hose #4 x 20" 6 SLF 90 x 6 SLF R1
-or-
H1601 2 Hose #4 x 28" 6 SLF 90 x 6 SLF R1
-or-
H1652 2 Hose #4 x 35" 6 SLF x 6 SLF 90 R1
-or-
H1612 2 Hose #6 x 36" 6 SLF 90 x 6 SLF 90
R1
62 H1628 1 Hose #6 x 112" 6 SLF x 6 SLF R1
63 M0005 9 Stud, 9/16 x 2-9/16 - 18 Plntry
64 D0111 1 Decal, CP16ATD (white)
D0115 1 Decal, CP18ATD (white)
Part List Cont.
REF PART QTY DESCRIPTION
(Rev. 7/4/2008)

20 Parts
MCPSSAMH (Rev. 8/25/2006)
Part List Cont.
D0125 1 Decal, CP24ATD (white)
D0321 1 Decal, CP30ATD (white)
D0371 1 Decal, CP36ATD
65 B0920 9 Washer, 9/16 flat SAE Plt Hrd
66 M0006 4 Stud, 1/2 x 2-3/16 UNF
67 M0009 1 Gasket, 2 Bolt B flange SAE
68 M0007 1 Pick tool, standard
69 M0048 1 Pick tool, KHP-2
70 D0042 1 Decal, planetary oil
71 F1470 2 Fitting, plug 12 SLM
72 855 2 Lock washer 1/2 ZP
73 D0192 2 Decal, pinch point
74 D0404 1 Decal, read manual
75 D0193 2 Decal, rotating cutter drum
76 H1693 1 Hose 3/8 68" 11/16 off 11/16 off
77 H1694 1 Hose 3/8 75" 11/16 off 11/16 off
78 D0107 1 Decal, depth CPA
79 D0108 1 Decal, tilt CPA
80 35124 2 7/16 x 2 Klik pin
81 D0323 1 Decal, important avoid motor
82 F1440 4 Fitting, 6 OM x 6 SLM ext
83 D0195 2 Decal, flying objects
84 D0445 1 Decal, controls danger
85 976 8 HHCS 3/8 NC x 1-1/2 GR5 ZP
86 B0618 10 Nut, 3/8-16 GR8 Stover lock
87 31982 6 HHCS 3/8 NC x 1-1/4 GR8 ZP
88 B0620 6 Washer, 3/8 Split lock GR2
89 21757 40 Washer, 3/8 STD SAE FLT
90 106471 1 Guard, Debris motor CPA -or-
106472 1 Guard, Debris motor CPA
91 106470 1 Guard, Debris deadshaft CPA
92 D0158 1 Decal, lift point
93 ----- 1 Serial number plate
94 D0438 1 Decal, caution valve arm
95 D0157 1 Decal, tie down
96 D0119 1 Decal, Alitec (white w/black)
97 1016085 1 Valve arm assembly
98 B1620 6 Washer, 1 flat SAE Plt Hrd
99 F1469 1 Fitting, plug 6 SLM
100 F1439 1 Fitting, 6 OM x 6 SLM ST orifice
101 19924 1 Decal, warning high pressure
102 54519 1 Decal, warning skid steer crush
A/R As required
REF PART QTY DESCRIPTION