World Market 608163 User manual

R
Assembly Instructions
Page 1
2023.03.15
Caspian Bar
SKU - 608163
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST WORLD MARKET STORE
IF YOU ARE NOT NEAR A STORE PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
All products sold at World Market are not for commercial use and are intended for residential use only.

Top Frame
LABEL DESCRIPTION Q.TY
PICTURE
A 1
Bottom Frame
B 1
Page 2
Component List
Divider Frame
C1
Left Side FrameD-1 1
Right Side Frame
D-2 1
Back Frame
E 1
Left Door Frame
F-1 1

LABEL DESCRIPTION Q.TY
PICTURE
Page 3
Component List
Right Door Frame
F-2 1
Fixed Shelf
G1
HandleH 2
Removable ShelfI 2
Adjustable Shelf
J1
Top Back Rail
K 1
Bottom Back Rail
L 1
Glassware Hanging Rail
M 1
Base Side Frame
N 2
Base Top Frame
O2
Base Bottom FrameP 2

LABEL Description Q.TY
PICTURE
Anti Tip-kit
Page 4
18
18
Cam lock Ø15 mm
1
LABEL DESCRIPTION QTY
1
T-1
T-3 Phillips Screwdriver (Not Included) 1
PICTURE
Allen Key 4 x 110 x 30 mm
H-1
H-2
H-3
H-4
H-5
H-6
H-7
H-8
H-9
H-10
Cam Screw
H-11
H-12
Screw M4 x 20 mm 4
10
Connecting Screw M7 x 50 mm
3Wood Screw M4 x 50 mm
16
Allen Bolt M6 x 20 mm
16
Lock Washer Ø6 x Ø10.5 x T1 mm
16
Flat Washer Ø6 x Ø16 x T1 mm
Pan Head Screw M4 x 45 mm 8
Pan Head Screw M3.5 x 20 mm 22
4
Shelf Pin Ø6
Hardware List
Tool List
T-2 Triangle 1

Before Beginning:
Page 5
Assembly Preparation
Read instructions, cover to cover.
In case of missing parts, please contact your nearest World Market store or call
our customer service call center at call 1-877-967-5362.
Assemble on a clean non-marring surface (packing foam).
Unpack all hardware bags and components to ensure you have all parts.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Save all packaging until finished.
WARNING: Small parts are a choking hazard. Adult Supervision is required
before, during, and after assembly.

Page 6
(T-3) Phillips Screwdriver
(H-2) Cam Screw x 18
D2
A
T-3
H-2
D1
G
Step 1
x8
Step 1.1: Install Cam Screws (H-2) into the pre-drilled holes on Left Side Frame (D-1) and Right Side Frame
(D-2) as shown. Fully tighten, but do not over tighten, using Phillips Screwdriver (T-3; not included). Reference
diagram above.
Step 1.2: Place Top Frame (A) and Fixed Shelf (G) upside down onto a padded, non-marring surface. Install
Cam Screws (H-2) into the pre-drilled holes on Top Frame (A) and Fixed Shelf (G) as shown. Fully tighten, but
do not over tighten, using Phillips Screwdriver (T-3; not included). Reference diagram above.
T-3
H-2
x10
Step 1.1:
Step 1.2:
Assembly Steps
Make sure Cam Screws are
tightened fully as shown

Step 2
Page 7
Step 3
(T-1) Allen key
(H-1) Cam Lock x 2
T-1
C
G
T-1
D-2
GC
Front
x2
x2
H-1
H-1
Front
Place Fixed Shelf (G) onto a padded, non-marring surface, oriented on its side as shown. Install Cam Locks
(H-1) into the corresponding holes on Divider Frame (C) as shown. Carefully lower Divider Frame (C) down,
making sure the Cam Screws (H-2) installed on Fixed Shelf (G) fit inside of Divider Frame (C). Tighten all Cam
Locks (H-1) using Allen Key (T-1) until they are snug.
Install Cam Locks (H-1) into the corresponding holes on Fixed Shelf (G) as shown. Position and secure the
Fixed Shelf (G) to Right Side Frame (D-2), making sure the Cam Screws (H-2) installed on Right Side Frame
(D-2) fit inside of Fixed Shelf (G). Secure the Cam Locks (H-1) using Allen Key (T-2) until snug.
(T-1) Allen key
(H-1) Cam Lock x 2

Step 4
Page 8
Step 5
T-1
H-1
K
L
D-2
x2
x2
Front
(T-1) Allen key
(H-1) Cam Lock x 6
Using a second person to assist you, rotate the assembly from Step 3 so that the FRONT faces down towards
the ground as illustrated. Install Cam Locks (H-1) into the corresponding holes on Fixed Shelf (G), Top Back
Rail (K) and Bottom Back Rail (L) as shown. Next, secure the assembly from step 3 and Right Side Frame
(D-2) to Top Back Rail (K) and Bottom Back Rail (L), making sure that the Cam Screws (H-2) installed face UP
inside Fixed Shelf (G), Top Back Rail (K) and Bottom Back Rail (L). Secure the Cam Locks (H-1) using Allen
Key (T-2) until snug.
T-1
T-1
H-1
H-1
x2
H-4
T-1
x10
(T-1) Allen key
(H-4) Connecting Screw x 10
Front
D-1
Install and secure Left Side Frame (D-1), Divider Frame (C) and Right Side Frame (D-2) to Bottom Frame (B)
using Connecting Screws (H-4). Engage all screws before fully tightening using Allen Key (T-1). Check that
the Caspian Bar is square (90 degree) using the Triangle (T-2).
B
Triangle
90°
(T-2) Triangle
T-2

Step 6
Step 7
(H-6) Allen Bolt x 16
(H-7) Lock Washer x 16
(H-8) Flat Washer x 16
(T-1) Allen key
Top
Step 6.1: Install and secure Base Top Frame (O) and Base Bottom Frame (P) to one of Base Side Frame (N)
using the Short Allen Bolt (H-6), Lock Washer (H-7) and Flat Washer (H-8), stacking the hardware in the order
shown. Engage all bolts by hand first, then tighten using an Allen Key (T-1).
Step 6.2: Continue attaching the Base Frame assembly to the other Base Side Frame (N), performing assembly
as step 6.1.
(T-3) Phillips Screwdriver
(H-9) Pan Head Screw x 8
Front
H-9
T-3
x8
Attach the Leg Base Frame assembly (from Step 6) with the assembly from Step 5. Secure the frame using
Pan Head Screws (H-9). Engage all screws by hand and then fully tighten them using Phillips Screwdriver (T-3)
(not included).
6.1 6.2
x16
H-6
H-7
H-8
T-1
P
P
O
O
N
N
Page 9

Step 8
Using a second person to assist you, carefully turn the assembly from Step 7 upright. Install Cam Locks (H-1)
into the corresponding holes on Left Side Frame (D-1) and Right Side Frame (D-2) as shown. Next, lower Top
Frame (A) down onto the assembly, making sure that Cam Screws (H-2) installed on Top Frame (A) fit inside of
Left Side Frame (D-1) and Right Side Frame (D-2). Tighten all Cam Locks (H-1) using Allen Key (T-1) until they
are snug.
(T-1) Allen key
(H-1) Cam Lock x 6
x6
Front
H-1
T-1
A
Page 10