World Market DUSTIN 550247 User manual

DUSTIN WOOD & METAL INLAY CABINET
SKU-550247
Page 1
Rev 3, 3/2018

Left Door Panel
Component List
LABEL DESCRIPTION QTY
A
B
C
D
E
F
G
H
I
J
K
L
M
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
3 PCS
4 PCS
1 PC
Right Door Panel
Middle Door Panel
Top Panel
Back Panel
Bottom Panel
Left Side Panel
Right Side Panel
Left Divider Panel
Right Divider Panel
Adjustable Shelves
Metal Legs
Middle Metal Leg
Page 2

TIPPING KIT CHECK LIST
CODE COMPONENT QTY
01 NYLON RESTRAINT STRAP
2
02 LONGER SCREW 4
03 SHORTER SCREW 4
04 PLASTIC ANCHOR
4
05 MOUNTING BRACKETS 4
LABEL
LABEL DESCRIPTION QTY
H-1 Bolts1/4”x5/8”xØ15mm
Cam Lock Nuts
Cam Lock Screws
Wood Dowels
Wood Screws Ø4 x 15mm
Bolts 5/32 x 12mm
Shelf Pins
Plastic Caps
Allen Key 110mm x 30mm
Screw Driver (Not Provided)
20 PCS
20 PCS
20 PCS
20 PCS
28 PCS
24 PCS
12 PCS
20 PCS
1 SET
1 PC
1 PC
H-2
H-3
H-4
H-5
H-6
H-7
H-8
T-1
T-2
DESCRIPTION QTY
Hardware
Tool List
Page 3
01
02
04
03
05

A
G
C
BF
LX4
MX1
E
I
J
K
K
K
D
H
Assembly Preparation
Page 4

Page 5
L
L
L
M
L
H-1
H-1
H-1
FH-1
H-1
(H-1) Bolts1/4”x5/8”xØ15 20 PCS
Step 1:
Assembly Steps
(T-1) Allen Key 110mm x 30mm 1 PC
* Position Metal Legs (L) and Middle Metal Leg (M) to corners and the center of Bottom Panel (F) ;
Secure by using Bolts (H-1) and fully tighten all bolts by Allen Key (T-1).
Adjust levelers if
needed for stability.

Page 6
Step 2:
(T-2) Screw Driver (Not Provided) 1 PC
(H-2) Cam Lock Nuts 4 PCS
(H-3) Cam Lock Screws 4 PCS
(H-4) Wood Dowels 6 PCS
Assembly Steps
G
*Install Cam Lock Screws (H-3) first then insert the Wood Dowels (H-4) on the Left and Right Side
Panels (G&H). Fit the holes in the edge of the Bottom Panel (F) over the Cam Lock Screws (H-3) and
Wood Dowels (H-4). Install Cam Lock Nuts (H-2) and tighten by turning clockwise using Screw
Driver (T-2). Must follow Cam Lock Nuts (H-2) position before tighten.
H-4
H-3
H-4
H-2
F
H
X 2

X 2
Page 7
(T-2) Screw Driver (Not Provided) 1 PC
(H-2) Cam Lock Nuts 4 PCS
(H-3) Cam Lock Screws 4 PCS
(H-4) Wood Dowels 6 PCS
Step 3:
Assembly Steps
J
I
G
H
F
F
H-2
H-4 H-3
*Install Cam Lock Screws (H-3) first, then insert the Wood Dowels (H-4) on the Bottom Panel (F).
Fit the holes in the edge of the Left and Right Divider Panels (I&J) over the Cam Lock Screws (H-3)
and Wood Dowels (H-4). Install Cam Lock Nuts (H-2) and tighten by turning clockwise using Screw
Driver (T-2). Must follow Cam Lock Nuts (H-2) position before tighten.
UP
UP
UP

X 4
Page 8
Step 4
(T-2) Screw Driver (Not Provided) 1 PC
(H-2) Cam Lock Nuts 12 PCS
(H-3) Cam Lock Screws 12 PCS
(H-4) Wood Dowels 8 PCS
Assembly Steps
*Install Cam Lock Screws (H-3) first, then insert the Wood Dowels (H-4) on the Top Panel (D).
Fit the Cam Lock Screws (H-3) and the Wood Dowels (H-4) on the Top Panel (D) to the holes in the
edge of the Left & Right Side Panels (G&H) and Left & Right Divider Panels (I&J). Install Cam Lock
Nuts (H-2) and tighten by turning clockwise using Screw Driver (T-2). Must follow Cam Lock Nuts
(H-2) position before tighten.
H-2
H-4
H-3
D
I
G
JH

Page 9
H-5
E
D
G
G
H-5
Step 5:
(T-2) Screw Driver (Not Provided) 1 PC
(H-5) Wood Screws 15 x Ø4 28 PCS
Assembly Steps
*Attach Back Panel (E) into pre-assembled unit (Step 4). Secure using Wood Screws (H-5) and fully
tighten by a Screw Driver (T-2).

Page 10
D
A
C
B
H
* Assemble Left Door Panel (A), Right Door Panel (B), and Middle Door Panel (C) to pre-assembled
unit (Step 5). Secure using Bolts (H-6) and fully tighten by a Screw Driver (T-2).
D
A
H-6
H-6
Step 6:
(T-2) Screw Driver (Not Provided) 1 PC
(H-6) Bolts 12 x Ø4 24 PCS
Assembly Steps

Page 11
Step 7:
Step 8:
(H-7) Shelf Pins 12 PCS
Assembly Steps
* Attach Plastic Caps (H-8) into the holes of Cam Lock by hand.
* Product is now completely assembled.
* Insert Shelf Pins (H-7) into Left and Right Side Panels (G&H) and Divider Panels (I&J). Then
insert Adjustable Shelves (K) into assembled unit.
KK
K
G
A
I
B
C
JH
H-7
H-7
H-7
KK
AI
B
CJ
(H-8) Plastic Caps 20 PCS
H-8

Dustin Wood & Metal Inlay Cabinet is now ready to use.
Page 12
Assembly Steps:

Side to Side Adjustment
loosen screw A, adjust gap
with screw B and re-tighten
Screw A.
Depth Adjustment
loosen screw A, push hinge
arm forwards or backwards,
re-tighten screw A and secure
Screw B with a 1/4 turn
clockwise.
Height Adjustment
loosen screw C, adjust door
height and re-tighten screw C.
C
C
A
B
A
B
* The doors can be adjusted in all 3 directions to create an even fit between doors on this cabinet.
Follow the appropriate directions above to adjust door(s) as necessary.
Page 13
Hinge Adjustment Guide

* If any door failed to close properly, adjust the length of the magnetic latch's pin by turning it
counterclockwise, as shown. The push pin's length will extend to allow the lock to engage. You will
hear a soft click. Door will close.
Page 13-2
Push-Latch Adjustment Guide

H
Page 14
Assembly Steps:
BACK SIDE
A
B
THE WALL
2x
2x
Installation Instruction:
1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the
shorter screws.
2. Determine where furniture is to be placed and mark location on the wall for the mounting
bracket screw hole approximately 2” below the bracket mountad to the edge of the furniture.
3. Drill a 3/6” hole in the wall. Press the plastic anchor into hole and gently tap until the flange
on the anchor is against the wall surface.
4. Position the bracket over the anchor and use the longer screw to securely attach the bracket
to the wall.
5. Place the furniture so the bracket on the back edge is in line with the bracket to the wall.
6. Lace an end of the nylon restraint strap down through each bracket. Bring both ends together
and slide the beaded end of the strap through the keyhole shaped slot in the other end until snug.
Pull down on the beaded end until it snap locks into the keyhole slot.
7. To double lock, return the beaded end back through the keyhole as show.
8. Check to make sure the strap is securely laced and locked to the brackets.

WARNING
Serious or fatal crushing injuries can occur from furniture tipover. To help prevent tip-over:
-Install tipover restraint provided.
-Place heaviest items in the lower drawers.
-Unless specifically designed to accommodate,do not set TVs or other heavy objects on top of this product.
-Never allow children to climb or hang on drawers, doors, or shelves.
-Never open more than one drawer at a time. (OR)
-Do not defeat or remove the drawer interlock system.
Use of tipover restraints may only reduce, but not eliminate, the risk of tipover.
This is a permanent label. Do not remove.
Care & Maintenance
Do not put hot items directly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
Do not place furniture in direct sunlight.
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside. For indoor use only.
Do not place furniture near heating or cooling vents.
Dust and clean-up spills using clean, non-colored, lint-free cloth.
Clean
Page 15