World Market RYDER 574837 User manual

Assembly Instructions
RYDER LAPTOP TABLE
SKU-574837, 574838
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Page 1
NOT FOR COMMERCIAL USE.

Page 2
Component List
LABEL
A 1
1
1
1
2
B
C
D
E
DESCRIPTION
Top Panel
Upper Support Frame
Lower Support Frame
Back Side Frame
Vertical Support Bars
QTY
LABEL DESCRIPTION QTY
Allen Key 4-1/3”x 1-1/6” 1T-1
Tool List
LABEL
H-1 6
2
8
H-2
DESCRIPTION QTY
Hardware
H-3
Small Allen Bolt (Ø1/4”x1/2”)
Large Allen Bolt (Ø1/4”x1”)
Button Head Allen Bolt (Ø1/5”x1/2”)
6H-4 Spring Washers (Ø2/5”xØ1/4”)

Page 3
Assembly Preparation
●Unpack all hardware bags and components to ensure you have all parts -
●Read instructions, cover to cover -
●Have two adults on hand for assembly -
●Do not assemble on flooring or carpet -
●Assemble on a clean non-marring surface (packing foam) -
●Save all packaging until finished -
●In case of missing parts, please contact your nearest Cost Plus Market
store or call out customer service call center at 1-877-967-5362.

Page 4
Assembly Steps:
Step 1
Attach Upper Support Frame (B) and Lower Support Frame (C) to Back Side Frame (D) by sliding
both frames over the metal blocks on Back Side Frame (D) as shown. Secure the frames using Button
Head Allen Bolts (H-3). Engage all bolts first before fully tightening with Allen Key (T-1).
H-3
B
C
D
X4
T-1
(H-3)
(T-1) Allen Key 4-1/3”x 1-1/6” 1PC
8 PCSButton Head Allen Bolt (Ø1/5”x1/2”)

Page 5
Assembly Steps:
Step 2
H-1
H-4
X2
X2
T-1
T-1
H-2
(H-1)
(H-2)
(T-1) Allen Key 4-1/3” x 1-1/6” 1PC
2 PCS
2 PCS
Small Allen Bolt (Ø1/4”x1/2”)
Large Allen Bolt (Ø1/4”x1”)
(H-4) 2 PCSSpring Washers (Ø2/5”xØ1/4”)
B
C
D
E
E
Attach Vertical Support Bars (E) to the Upper Support Frame using Small Allen Bolts (H-1) and
Spring Washers (H-4), stacking the hardware in the order as shown. Next attach the bottom of the
Vertical Support Bars (E) to Lower Support Frame (C) using Large Allen Bolts (H-2). Engage all bolts
first and then fully tighten using Allen Key (T-1).

Page 6
Assembly Steps:
Step 3
T-1
H-1
H-4
A
(H-1)
(T-1) Allen Key 4-1/3” x 1-1/6” 1PC
4 PCS
Small Allen Bolt (Ø1/4”x1/2”)
(H-4) 4 PCSSpring Washers (Ø2/5”xØ1/4”)
Place the Top Panel (A) upside down onto a padded, non-marring surface. Attach the assembled base
frame (from Step 2) to Top Panel (A) and secure using 4 Small Allen Bolts (H-1) and 4 Spring
Washers (H-4), stacking the hardware in the order as shown. Engage all bolts first and then fully
tighten using Allen Key (T-1).

Page 7
Assembly Steps:
Carefully turn the table upright and then it is now ready for use.
Levelers can be used for
adjustment if needed.
NOTE:

Care & Maintenance
Do not put hot items directly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
Do not place furniture in direct sunlight.
Do not place furniture near heating or cooling vents.
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside. For indoor use only.
Dust and pick-up spills using a clean,
Recommend using coasters to protect table top. Wipe spills immediately
with a sofe, dry cloth.
NOTE
non-colored, lint-free, dry cloth.
Not for commercial use. For residential use only.
Page 8