World Market 556231 User manual

Randall Cane Top Desk
SKU - 556231
Assembly Instructions
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Page 1

Page 2
Component
LABEL
A
B
C
D
E
Desk top with glass 1
Shelf frame 1
1
2
2
DESCRIPTION QTY
List
Hardware List
LABEL DESCRIPTION
H-1 Pan Head Allen Bolt (Ø6x15mm) 20
H-2
H-3
H-4
H-5
6
4
Bolt (M6x40mm)
Bolt (M6x30mm)
QTY
Spring Washer (Ø6xØ11x2mm) 10
10
Flat Washer (Ø6xØ18x2mm)
Support rail
Leg I
Leg II
H-6 1
TIPPING KIT CHECK LIST
CODE COMPONENT QTY
01 PLASTIC STRAP 2
02 SCREW 4
03 NYLON WALL PLUG 2
04 METAL BRACKET 4
03 04
02
01
Tool List
T-1
Phillips head screw driver tool
needed (not included )
T-2
Ball allen key (M4x30x110mm) 1
LABEL DESCRIPTION QTY

Page 3
Assembly Preparation
Before Beginning:
A
C
B
E
DE
D
Read instructions, cover to cover.
Have 2 adults on hand for assembly.
Save all packaging until
Assemble on a clean non-marring surface (packing foam).
Do not assemble on ooring or carpet.
In case of missing parts contact your nearest Cost Plus World Market store or our
customer service call center 877-967-5362.
Unpack all hardware bags and components to ensure you have all parts.

Page 4
Assembly Steps
Step 1
Step 2
1. Attach Leg I (D) and Leg II (E) to Shelf Frame (B) .
2. Secure using Pan Head Allen Bolt (H-1), Bolt (H-2), Spring Washer (H-4),
Flat Washer (H-5) with ball allen key (T-1) as shown
Do Not fully tighten any hardware yet.
1. Take the glass out of the Desk Top.
2. Attach Support Rail (C) to Desk Top (A). Secure with Bolt (H-3), Spring Washer(H-4),
Flat Washer (H-5) with ball allen key (T-1) as shown
4x
4x
T-1
T-1
H-1
H-2 H-4 H-5
A
B
C
E
E
D
D
T-1
H-3
H-4
H-5
4x

Page 5
Assembly Steps
Step 3
Step 4
1. Attach step 3 assembly to Desk Top (A) with pan head allen bolt (H-1).
2. Secure Shelf frame (B) to Support Rail (C) with Bolt (H-2), Spring washer (H-4),
Flat Washer (H-5).
Turn Desk right side up and insert the glass into Desk top
3. Fully tighten all Bolts with ball allen key (T-1) and make sure all hardware is engaged.
T-1
H-1
16x
2x
Adjust levelers if
needed for stability.
Tempered clear glass
T-1 H-2
H-4
H-5

Assembly Steps
Installation Instruction:
Attach one of the mounting brackets securely near the top back edge of the furniture piece
by inserting the screw.Refer to picture A.
Determine the final position of the furniture piece. Mark location on the wall approximately
2” below the bracket mounted to the back of the furniture.
Drill a starter hole into the wall stud. If wall stud is not available, drill a hole into the wall
and insert plastic anchor. Gently tap anchor until the flange of the anchor is flush with the wall.
Attach the second bracket by inserting and securing the screw to the wall. Refer to picture B.
Align the two brackets.
Insert the strap through both brackets and tighten until snug.
Check to make sure that the brackets are firmly installed the strap is secure.
BACK SIDE
A
B
THE WALL
2x
2x
03 04
02
01
Page 6
0.5"

Care & Maintenance
.
.
.
.
.
.
.
.Do not put hot items direct ly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
Do not place furniture in direct sunlight.
Do not place furniture near
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside. For indoor use only.
Dust and pick-up spills using a clean, non-colored, lint-free cloth.
Not for commercial use. For residential use only.
Page 7
heating or cooling vents.