World Market 589790 User manual

SPENCE SLAT CABINET
SKU–589790
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877- 967-5362 FOR ASSISTANCE.
NOT FOR COMMERCIAL USE.
Page 1
Assembly Instructions

LABEL
Page 2
Component List DESCRIPTION QTY
ACabinet Body
B
C
1
Shelf
Leg
2
4
1
Hardware List
H-1 Allen Bolt
M6 x 60 mm
Flat Washer
M6x16mm
H-3 Lock Washer
M6
8
8
8
H-4 Metal Shelf Pin 8
Tool List
LABEL
H-2
DESCRIPTION QTY
LABEL DESCRIPTION QTY
Allen Wrench
N4
T-1

Assembly Preparation
Before Beginning:
• Unpack all hardware bags and components to ensure you have all parts-
• Read instructions, cover to cover-
• Have 2 adults on hand for assembly-
• Do not assemble on flooring or carpet-
• Assemble on a clean non-marring surface (packing foam)-
• Save all packaging until finished-
• In case of missing parts, please contact your nearest Cost Plus World
Market store or call our customer service call center at call 1-877-967-5362.
Page 3
A
B
CC
C
C
(H-3) Lock Washer x 8
Metal Shelf Pin x 8(H-4)
Allen Bolt x 8(H-1)
(H-2) Flat Washer x 8

Allen Bolt x 8(H-1)
Assembly Steps
Step 1
Page 4
Allen Wrench x 1
(T-1)
(H-2) Flat Washer x 8
(H-3) Lock Washer x 8
A
C
C
C
C
Place Cabinet Body (A) upside down onto a padded, non-marring surface as shown. Attach Legs
(C) to each corner as illustrated and secure each leg using 2 Allen Bolts (H-1), Lock Washers (H-3)
and Flat Washers (H-2), stacking the hardware in the order shown. Engage all bolts by hand first,
then fully tighten them usingAllen Wrench (T-1).
FRONT
TOP

Assembly Steps
Page 5
Step 2
A
B
B
Metal Shelf Pin x 8(H-4)
NOTE: ADJUST LEVELERS TO PREVENT ROCKING IF FLOOR IS UNEVEN.
NOTE: Shelves (B) are reversible,
meaning they can be installed on
either side of the cabinet.
TOP
FRONT
Using a second person to assist you, carefully turn the cabinet assembly upright. Fully open both
pre-installed doors on Cabinet Body (A). Next, install Metal Shelf Pins (H-4) into the desired hole
position on the inside edges of the cabinet as shown. NOTE: there are 3 holes representing 3
height positions for the shelf. Make sure Metal Shelf Pins (H-4) are attached in the same hole
position for all remaining corners. Insert both Shelves (B) on angle into Cabinet Body (A) as
shown, aligning the corner notches with each edge. Make sure both Shelves (B) rest evenly on
Metal Shelf Pins (H-4).
Assembly is now complete and the product is ready for use. NOTE: Levelers on the bottom of
each leg may be used for additional adjustments if needed for uneven floor surfaces.

Care & Maintenance
• Do not put hot items directly on furniture surface.
• Do not clean furniture with harsh cleansers or polish.
• Do not place furniture in direct sunlight.
• Do not place furniture near heating or cooling vents.
• Do not write on furniture without a padded barrier to protect the surface.
• Do not place furniture outside. For indoor use only.
• Not for commercial use. For residential use only.
• Dust and pick-up spills using a clean, non-colored, lint-free, dry cloth.
Page 6
• For dirt and surface markings, apply a small amount of dish soap to
a clean, lint-free cloth rinsed in lukewarm water. Wipe surface clean.