World Market Cortez Woven 608166 User manual

THANK YOU FOR PURCHASING OUR QUALITY PRODUCT. IF YOU HAVE ANY
QUESTIONS PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE,
PLEASE CONTACT YOUR NEAREST WORLD MARKET STORE, OR CALL OUR
TOLL FREE NUMBER 877-967-5362 FOR ASSISTANCE.
Cortez Woven 3 Door Buffet
R
Assembly Instructions
SKU - 608166
NOT FOR COMMERCIAL USE.
Page 1

Part List
Page 2
E : Back Panel - 1 pc
A: Top Panel - 1 pc B: Bottom Panel - 1 pc
D-2: Right Side Panel - 1 pc
F-1 : Left Door Frame - 1 pc
D-1: Left Side Panel - 1 pc
C: Divider Panel - 1 pc
G : Large Shelf - 1 pc H: Small Shelf - 1 pc
J : Leg - 4 pcs K : Center Leg - 1 pc
F-2 : Right Door Frame - 1 pc
F-3 : Mid Door Frame - 1 pc

LABEL DESCRIPTION Q.TY PICTURE
Anti Tip-kit
Page 3
8
26
9
9
9
Cam lock Ø15 mm (Minifix)
1
Pan head Screw 3.5 x 20 mm
Shelf Pin Ø6
Hardware List
LABEL DESCRIPTION QTY
1
T-1
T-2
Phillips Screwdriver
(Not Included) 1
PICTURE
Allen Key
4 x 110 x 30 mm
Tool List
H-1
H-2
H-3
H-4
H-5
H-6
Cam Screw (Minifix Bolt)
Connecting Screw M7 x 50 mm

Before Beginning:
Read instructions, cover to cover.
In case of missing parts, please contact your nearest World Market store or
our customer service call center 877-967-5362.
Assemble on a clean non-marring surface (packing foam).
Unpack all hardware bags and components to ensure you have all parts.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Save all packaging until finished.
Assembly Preparation
Page 4

Step 1
Assembly Steps
Page 5
(T-2) Phillips Screwdriver
(H-2) Cam Screw x 9
A
Front
Step 2
Install and secure Left Side Panel (D-1) and Right Side Panel (D-2) to Bottom Panel (B) using Connecting
Screws (H-3). Secure Divider Panel (C) to Bottom Panel (B) using Connecting Screws (H-3).
Engage all screws by hand first and then fully tighten them using Allen Key (T-1)
(T-1) Allen key
(H-3) Connecting Screw x 9
T - 2
H - 2
Place Top Panel (A) upside down onto a padded, non-marring surface. Install Cam Screws (H-2) into the
pre-drilled holes on Top Panel (A) Fully tighten using a Phillips screwdriver (T-2) (not included).
Set the Top Panel assembly aside until Step 4.
Front B
H - 3
D-1
D-2
C

Page 6
Step 3
Step 4
Using a second person to assist you, carefully turn the assembly from Step 3 upright so that it rests evenly on
all the legs. Attach the Left Door Frame (F-1), Right Door Frame (F-2) and Mid Door Frame (F-3) by inserting
the bottom door pivot hinge ( pre-installed on Doors ) into the corresponding sleeve holes along the front edge
of Bottom Panel (B) as shown. All three Doors (F) must be installed prior to placing Top Panel (A) onto
the assembly. With the doors installed, use a second person to assist you and carefully lower Top Panel (A)
down onto the assembly. Align all of the cam screws (installed in Step 1) with their corresponding holes on
Panels D-1/C/D-2 and ensure that the top door pivot hinge on each door fits into their respective sleeve hole on
Top Panel (A).
F-1
A
Front
Position and secure Legs (J) and Center Leg (K) to Bottom panel (B) by using screw of legs.
J
J
K
Front
B
B
F-3
F-2

Page 7
Step 5
After installing All Cam Locks (H-1), ensure the Top Panel (A) is fully seated down onto the Left / Right Side
Panels (D-1/D-2) and Divider Panel (C), and the three Doors (F1, F2 & F3) and their pivot hinges are all properly
engaged. Once confirmed, fully tighten all Cam Locks (H-1) by turning clockwise using Allen Key (T-1) until they
are snug. DO NOT over tighten Cam Locks.
T - 1
Insert Cam Locks (H-1) into the Left/Right Side Panels (D-1/D-2) and the Divider Panel (C) following the
orientation directions above.
The arrow on the Cam Lock (H-1) must point towards the Cam Screw (H-2) when first inserting the Cam Lock.
There are three Cam Locks per each of the panels.
(T-1) Allen key
(H-1) Cam Lock x 9
Step 5.3
Lock
Step 5.2
Step 5.1
Insert Fully
Follow Arrow direction

Page 8
Step 6
Step 7
Step 7.1: Insert Shelf Pins (H-5) into the desired hole locations on Left / Right Side panel (D-1/D-2) and Divider
Panel (C).
Step 7.2: Insert Shelf (G/H) into position as shown, making sure they rest evenly on each Shelf Pin (H-5).
(H-4) Pan Head Screw x 26
(T-2) Phillips Screwdriver
x26
Attach Back Panel (E) to the back of the storage assembly as shown. Secure the panel using Pan Head Screws
(H-4) and a Phillips head screwdriver (T-2) (not included).
(H-5) Shelf Pin x 8
G
H
H - 4
T - 2
E
H - 5
Step 7.1
Step 7.2
Front

Page 9
Step 8
NOTE: Levelers can be used
for adjustment if needed.
ADJUSTABLE LEVELER
Ensure that all bolts have been fully tightened.
Assembly is now complete and the Cortez Woven 3 Doors Buffet is ready for use.
NOTE: Levelers can be adjusted for additional stability if needed.

Page 10
Do not put hot items directly on furniture surface.
Do not clean furniture with harsh cleansers or polish.
Do not place furniture in direct sunlight.
Do not place furniture near heating or cooling vents.
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside. For indoor use only.
Not for commercial use. For residential use only.
Dust and pick-up spills using a clean,non-colored, lint-free cloth.
Cleaner
Care & Maintenance