World Market Jagger 626729 User manual

R
Jagger Record Media Cabinet 60''
SKU 626729
PAGE 1
2023.08.08
Assembly Instructions
ALL PRODUCTS SOLD AT WORLD MARKET ARE NOT
FOR COMMERCIAL USE AND ARE INTENDED FOR
RESIDENTIAL USE ONLY
Thank you for your purchase. If you have any questions pertaining to the assembly of this
furniture piece, please contact the nearest World Market store. If you are not near a store,
please call our customer service call center toll free at 877-967-5362 for assistance.

LABEL DESCRIPTION Q.TY
PICTURE
Component List
A
Leg
1
Top Frame
Bottom Frame
Left Side Frame
Right Side Frame
Mid Divider Frame
Left Divider Frame
Adjustable Shelf
Back Panel
Lid
B
C-1
C-2
1
1
1
2
D-1
D-2 1
1
E
F
G
1
1
4
I
TOP FRONT
TOP FRONT
TOP
TOP
TOP
TOP
TOP FRONT
FRONT
TOP
TOP
TOP
PAGE 2

Anti Tip-kit
Lock Washer Ø8 x Ø13 x T2 mm
Nut M8 x 13 mm
10
Cam lock Ø15 mm
Pan head Screw M3.5 x 25 mm
Shelf Pin Ø6
Cam Screw
Connecting Screw M7 x 50 mm
Connector Bolt M6 x 10 mm
(inside)
Allen Bolt M6 x 20 mm
Large Flat Washer
Ø10 x Ø20 x T2 mm
LABEL DESCRIPTION Q.TY
PICTURE
Hardware List
H-1
H-2
H-3
H-4
H-5
H-6
H-7
H-8
H-9
H-10
H-11
H-12
10
10
32
4
1
1
1
Small Flat Washer
Ø8 x Ø16 x T2 mm 8
8
8
1
PAGE 3

Tool List
LABEL DESCRIPTION QTY
1
T-1
Phillips Screwdriver
(Not Included)
PICTURE
Allen Key
4 x 110 x 30 mm
Wrench 13 mm
Triangle
T-2
T-3
T-4
1
1
1
PAGE 4

Assembly Preparation
Before Beginning:
Read the assembly instructions, cover-to-cover. Save any Care and Maintenance instructions pages for
after the assembly has been completed.
In case of missing parts, please contact your nearest World Market store or call our customer service call
center at call 1-877-967-5362.
Assemble on a clean non-marring surface (such as the product's packing foam).
Unpack all hardware bags and components to ensure you have all parts. Take note of bolt hardware
size differences and components that may have directional labels (Example: TOP or FRONT).
It is always recommended to have 2 adults on hand for assembly.
Do not assemble on hard, abrasive flooring or carpeted surfaces that can damage or get caught in the
components during assembly.
Do not discard any packaging until the product has been fully assembled.
WARNING: Small parts are a choking hazard. Adult supervision is required before, during, and after
assembly.
PAGE 5

Step 1
Assembly Steps
Place Top Frame (A) upside down onto a padded, non-marring surface. Install Cam Screws (H-2) into the
pre-drilled holes on Top Frame (A) as shown. Fully tighten using a Phillips screwdriver (T-4, not included) per
illustration above.
(T-4) Phillips Screwdriver
(H-2) Cam Screw x 10
Step 2
(H-1) Cam Lock x 10 (T-1) Allen key
FRONT
TOP
FRONT
IMPORTANT:
Please make note of the different
hardware sizes and ensure you are
using the correct size hardware (bolts,
screws, and washers) for each step.
A
T-4
H-2
Using a second person to assist you, hold the Top Frame (A) on the front edge as illustrated. Position the Left/Right
Side Frames (C-1/C-2) and the Left/Mid Divider Frames (D-1/D-2) with the Top Frame (A) so that the previously
installed Cam Screws (H-2) and dowels are inserted into their corresponding holes. Note the position of the Cam
Lock (H-1) holes. Install Cam Locks (H-1) into all components as illustrated above, ensuring the arrows point
toward the corresponding Cam Screws (H-2). Once placed, fully tighten Cam locks (H-1) by turning clockwise
using the provided Allen Key (T-1). Fully tighten but DO NOT over tighten. The assembly should now be able to
stand on its own.
x10
T-1
Follow arrow
direction
x10
AD-2
H-1
H-2
D-1 D-1
C-1
C-2
Make sure Cam Screws are
tightened fully as shown
PAGE 6

Step 4
Step 3
(T-1) Allen key
(H-3) Connecting Screw x 10
(H-6) Connector bolt x 1
(H-7) Allen bolt x 1
(H-8) Large Flat washer x 1
Using a second person to assist you, carefully position the Bottom Frame (B) with the assembly by inserting the
dowels in Left/Right Side Frames (C-1/C-2) and Mid/Left Divider Frame (D-1/D-2) into their receiving holes in
the Bottom Frame (B). Once engaged, use the provided 90 Degree Triangle (T-3) to ensure the assembly is square.
If there is a gap between either edge of the Triangle (T-3), adjust the assembly until there are no gaps. Once
satisfied, secure the connection by engaging all Connecting Screws (H-3) first by hand, then fully tightening using
the provided Allen Key (T-1), as shown. Do no over tighten.
G
H-7H-8
H-6
(T-1) Allen key
x10H-3
T-1
C-1
D-1
D-1
D-2
C-2
A
B
Triangle
90°
FRONT
x1
F
Position Lid (G) to Back Panel (F). Secure with Connector Bolt (H-6), Large Flat Washer (H-8) and Allen Bolt
(H-7) using provided Allen Key (T-1), stacking the hardware through Back Panels in the order as shown. Engage
all bolts first then fully tighten. DO NOT over tighten.
(T-3) Triangle
T-3
T-1
FRONT
TOP
PAGE 7

(H-4) Pan Head Screw x 32
(T-4) Phillips Screwdriver
(H-9) Small Flat Washer x 8
(H-10) Lock Washer x 8
(H-11) Nut x 8
(T-2) Wrench
Step 6
Step 5
Check that the cabinet is square (90 degrees) using Triangle (T-3). Once square, position Back Panel (F) onto
assembly as shown. Make sure panel is oriented correctly (Connecting Bolt from previous step should point toward
the top). Secure around the perimeter of the cabinet with Pan Head Screws (H-4) using Phillips Screwdriver (T-4;
not included). DO NOT over tighten.
x32
H-4
Triangle
90°
(T-3) Triangle
C-2 B
F
Using a second person to assist you, carefully turn the assembly upside down onto a padded, non-marring surface.
Install and secure Legs (I) to Bottom Frame (B) with Small Flat Washers (H-9), Lock Washers (H-10) and Nuts
(H-11) using provided Wrench (T-2), stacking the hardware in the order as shown. Engage all Nuts (H-11) first,
then fully tighten. DO NOT over tighten.
H-9
H-10
H-11
T-2 A
C-2
D-2 D-1 D-1 C-1
B
I
I
FRONT
TOP
T-3
T-4
FRONT
TOP
PAGE 8

Step 7
Step 8
ADJUSTABLE LEVELER
Levelers are located on the bottom of
each Leg and may be used for
additional adjustment if needed for
uneven surfaces.
Step 7.1
H-5
x4
(H-5) Shelf Pin x 4
Step 7.1: Using a second person to assist you, carefully turn assembly upright. Insert Shelf Pins (H-5) into the
desired hole locations on Right Side Frame (C-2) and Mid Divider Frames (D-2)
Step 7.2: Turn Adjustable Shelf (E) diagonally and carefully insert into position as shown, making sure they rest
evenly on each Shelf Pin (H-5). The cut out in each Shelf should be toward the back.
Step 7.2
E
C-1 D-1 D-1
D-2
C-2
A
TOP
FRONT
Vertical storage compartments are
designed to fit most standard size
Long-Playing (LP) Vinyl Records.
Assembly is now complete and the product is ready for use. Adjustable levelers are located on the bottom of each
leg and may be adjusted by turning outwards, counter-clockwise to help account for uneven surfaces.
NOTE: Hardware may loosen over time. Periodically check that all connections remain tight and adjust as needed.
PAGE 9

Anti-Tip Measures
Furniture tip overs can result in death or serious injuries. To reduce the likelihood of tip over, this product should be used with the enclosed
Anti-Tip Kit. This Anti-Tip Kit is only a deterrent. It is not a substitute for proper adult supervision. Manufacturer and retailer assume no
liability for improper installation or excess loads placed on screws, brackets, or straps. When properly installed, this restraint provides
protection against unexpected tipping of furniture. This Anti-Tip Kit MUST be installed into the wall using proper mounting hardware OR
into a wall stud using appropriate screws. Position of the Anti-Tip Kit depends on the product and the location of the wall studs. The
hardware provided is not a comprehensive solution for all wall types. Be sure to consult a professional or your local hardware store to
determine the hardware needed for your specific wall type (plaster, drywall, concrete, etc.).
WARNING
Using a second person to assist you, place the unit in the desired final location against a wall. It is suggested to
use a stud finder to find wall studs along the length of the unit and roughly 1 inch below the top. Where
possible, mark a drill hole position on the wall where there is a stud and use a Drill or Screwdriver (NOT
INCLUDED) to attach Wall Brackets to the wall using Long Screws in the location of the wall studs.
In a case where there is no wall stud, hold Brackets on wall and mark the drill hole positions so that they are
roughly 1 inch below the top of the piece. Using a Drill (NOT INCLUDED) with a drill bit roughly the
diameter of the plastic Wall Plugs, drill pilot holes in marked positions. Insert the plastic Wall Plugs into the
holes until the tops are roughly flush with the wall. Align the holes and insert the Long Screws through
Brackets and into the corresponding holes in the wall using a Phillips Head Screwdriver (NOT INCLUDED).
Next, attach remaining 2 Brackets to the back of the piece using Short Screws so they align with Brackets
installed on the wall. Loop Straps through Brackets (A) on the furniture piece, then through Brackets on the
wall and tighten until snug. Installation is now complete.
IMPORTANT: Check that the Wall Brackets are firmly screwed into the wall and the Cable Ties are snug.
If there is any hesitation, please consult a professional or your local hardware store.
75 mm
Anti-Tip kit contents Anti-Tip kit installation
PAGE 10