Worx Professional WU172 1 Series User manual

Lithium-Ion cordless drill/driver
W U172 W U172 .1 W U172 . 9 W U172 . A


4
5
7
1 2 3
8
9
6

2
1
2
3
1
2
3
1
C1
A2A10
A3 B1
B2
C3C2
FD
E

2
1
2
3
1
2
3
1
C1
A2A10
A3 B1
B2
C3
C2
FD
E

6
EN
PRODUCT SAFETY
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING: Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to
power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by

7
EN
the manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
e) Do not use a battery pack or tool that is damaged
or modified. Damaged or modified batteries may
exhibit unpredictable behaviour resulting in fire,
explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specified
range may damage the battery and increase the risk
of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
DRILL SAFETY WARNINGS
1 ) Safety instructions for all operations
a) Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory or fasteners may contact
hidden wiring or its own cord. Cutting accessory or
fasteners contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give
the operator an electric shock.
2) Safety instructions when using long drill bits
a) Never operate at higher speed than the
maximum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
b) Always start drilling at low speed and with the
bit tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to rotate
freely without contacting the workpiece, resulting in
personal injury.
c) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resulting in
personal injury.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells or battery
pack.
b) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer
where they may short-circuit each other or be
short-circuited by conductive materials. When
battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause burns or a
fire.
c) Do not expose battery pack to heat or fire. Avoid
storage in direct sunlight.
d) Do not subject battery pack to mechanical shock.
e) In the event of battery leaking, do not allow the
liquid to come into contact with the skin or eyes.
If contact has been made, wash the affected area
with copious amounts of water and seek medical
advice.
f) Seek medical advice immediately if a cell or battery
pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a clean dry
cloth if they become dirty.
i) Battery pack needs to be charged before use.
Always refer to this instruction and use the correct
charging procedure.
j) Do not maintain battery pack on charge when not
in use.
k) After extended periods of storage, it may be
necessary to charge and discharge the battery pack
several times to obtain maximum performance.
l) Battery pack gives its best performance when it is
operated at normal room temperature (20 °C ± 5 °C).
m) When disposing of battery packs, keep battery
packs of different electrochemical systems separate
from each other.
n) Recharge only with the charger specified byWorx.
Do not use any charger other than that specifically
provided for use with the equipment. A charger that
is suitable for one type of battery pack may create a
risk of fire when used with another battery pack.
o) Do not use any battery pack which is not designed
for use with the equipment.
p) Keep battery pack out of the reach of children.
q) Retain the original product literature for future
reference.
r) Remove the battery from the equipment when not
in use.
s) Dispose of properly.
t) Do not mix cells of different manufacture, capacity,
size or type within a device.
u) Do not remove battery pack from its original
packaging until required for use.
v) Observe the plus (+) and minus (–) marks on the
battery and ensure correct use.

8
EN
SYMBOLS
To reduce the risk of injury, user must
read instruction manual
Wear ear protection
Wear eye protection
Wear dust mask
Do not burn
Batteries may enter water cycle if
disposed improperly, which can be
hazardous for ecosystem. Do not
dispose of waste batteries as unsorted
municipal waste.
Warning
Wear protective gloves
Lock
Screw driving
Drilling
Wood
Metal
High speed
Low speed
Li-Ion battery. This product has been marked
with a symbol relating to ‘separate collection’
for all battery packs and battery pack. It will
then be recycled or dismantled in order
to reduce the impact on the environment.
Battery packs can be hazardous for the
environment and for human health since
they contain hazardous substances.
COMPONENT LIST
1. Keyless chuck
2. Torque adjustment ring
3. Two-speed gear control
4. Forward/Reverse rotation control
5. Soft grip handle
6. Battery pack release button*
7. Battery pack*
8. LED light
9. On/off switch
*Not all the accessories illustrated or described are
included in standard delivery.
TECHNICAL DATA
WU172WU172.1
WU172.A WU172.9
Voltage 20 V Max**
No load speed 0-400/0-1500 /min
Number of clutch
positions 15+1
Max torque 40 N.m
Chuck capacity 10 mm
Max. drilling
capacity
Steel 10 mm
Wood 30 mm
Machine weight 1.3kg 1.0kg
**Voltage measured without workload. Initial
battery voltage reaches maximum of 20 volts.
Nominal voltage is 18 volts.

9
EN
ACCESSORIES
WU172 WU172.1 WU172.9 WU172.A
2.0Ah
Lithium
Battery pack
(WA3593)
2 1 / /
2A Charger
(WA3924) 1 1 / /
We recommend that you purchase your accessories
listed in the above list from the same store that sold you
the tool. Refer to the accessory packaging for further
details. Store personnel can assist you and offer advice.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal and plastic.
Assembly and Operation
ACTION FIGURE
BEFORE OPERATION
Removing the battery pack See Fig. A1
Charging the battery See Fig. A2
Installing the battery pack See Fig. A3
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger
switch and disconnect tool from
power source when changing
accessories. Always ensure the bit is
secure before starting the tool. Damage
to the Chuck or a loose bit may cause
possible personal injury.
Removing the bits See Fig. B1
Inserting the bits See Fig. B2
OPERATON
Forward/reverse rotation control
WARNING: Never change the
direction of rotation when the chuck
is rotating, wait until it has stopped!
See Fig. C1,
C2, C3
TWO-SPEED GEAR CONTROL
WARNING: To prevent gear
damage, always allow the chuck to
come to a complete stop before
changing the direction of rotation.
See Fig. D
TORQUE ADJUSTMENT
Screw driving
Drilling
See Fig. E
Operating the On/Off Switch
WARNING: Do not operate for
long periods at low speed because
excess heat will be produced internally.
See Fig. F
LED light indicator
Before operation, the LED light will be
activated when the On/Off switch is
slightly depressed.
The tool and battery are equipped with a
protection system. When the LED Light
is quickly flashing 3 seconds and turn
off, the system will automatically cut off
power to the tool to extend battery life.
The tool will automatically stop during
operation if the tool and/or battery
are placed under one of the following
conditions:
• Overloaded: The tool is operated
in a manner that causes it to draw
an abnormally high current. In this
situation, release the Trigger Switch on
the tool and stop the application that
caused the tool to become overloaded.
Then pull the Trigger Switch again to
restart.
• Overheated: Under the condition
above, if the tool does not start, the
Tool and Battery are overheated. In this
situation, let the Tool and Battery cool
before pulling the Trigger Switch again.
• Low battery voltage: The remaining
Battery capacity is too low and the
tool will not operate. In this situation,
remove and recharge the Battery.
Warning: To turn on the light, press
the On/Off switch and make sure
the Forward/Reverse Rotation Control is
on right/left position.
See Fig. F
PROBLEM SOLUTION
1. WHY DOESTHE DRILL NOTTURN ON WHENYOU
PRESSTHE SWITCH?
The forward/reverse rotation control, which is on top of
the trigger, is positioned in the lock function. Unlock the
forward/reverse rotation control by putting it into the
required rotation position. Push the trigger and the drill will
start to rotate.
2.THE DRILL STOPS BEFORETHE SCREW IS
COMPLETELYTIGHTENED.WHY?
Verify the torque position of the torque adjusting ring, you
can find the torque-adjusting ring between the chuck and
the drill body. Position 1 is the lowest torque (screw driving
force) and position 15 is the highest torque (screw driving
force). Position is for drill operation. Regulate the torque
adjusting ring to a higher position to reach the best result.
3. REASONS FOR DIFFERENT BATTERY PACK
WORKINGTIMES
Charging time problems, as above, and having not used a
battery pack for a prolonged time will reduce the battery
pack working time. This can be corrected after several
charge and discharge operations by charging & working
with your drill. Heavy working conditions such as large

10
EN
screws into hard wood will use up the battery pack energy
faster than lighter working conditions. Do not re-charge
your battery pack below 0oC and above 45oC as this will
affect performance.
MAINTENANCE
Remove the battery pack from the tool before
carrying out any adjustment, servicing or
maintenance.
Your tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your
power tool. Wipe clean with a dry cloth. Always store
your power tool in a dry place. Keep the motor ventilation
slots clean. Keep all working controls free of dust.
Occasionally you may see sparks through the ventilation
slots. This is normal and will not damage your power tool.
FOR BATTERY TOOLS
The ambient temperature range for tool and battery use
and storage is 0oC -45oC.
The recommended ambient temperature range for the
charging system during charging is 0oC -40oC.
ENVIRONMENTAL
PROTECTION
Disposal
The machine, its accessories and
packaging materials should be sorted for
environmentally friendly recycling.
The plastic components are labeled for categorized
recycling.

HE
0°C
הקוזחת
הללוסה ילכ
.
.
הביבס תוכיא לע הרימש
קוליס
מ”עב סיסקל םוקימס :הרבחה םש
הדוהי ןבא 9090 .ד.ת המידק יברעמ ת”א :תבותכ
09-7611222 :ןופלט
www.semicom.co.il

HE
שמתשמל ךירדמ
שומישה ינפל ךירדמה תא ןויעב ארק אנא :קתפ
.ילכב
דעוימ שומיש
לועפתו הבכרה
ילטיגיד הלועפ
A1
A2
A3
קא›צ תמאתה
:הרהזא
B1
B2
תירוחאו המידק הטילש
:הרהזא
D
תיריהמ-וד םיכוליה תרקב
:הרהזא
הלעפה לש יוביכ / הלעפה
:הרהזא
דל יוויח
.LED
LED
3
ידמ רתוי סימעהל •:
:רתי תוממחתה •
:ךומנ הללוס חתמ •
:הרהזא
תויעב ןורתיפ
1
2
1
3

HE
3
.
n
n
רישכמה יקלח
חתפמ אלל קא'צ .1
טנמומ ןונוויכ תעבט .2
תיריהמ-וד םיכוליה תרקב .3
הכופה / המידק בוביס תרקב .4
הכר הזיחא תידי .5
* תוללוס רורחש ןצחל .6
* תוללוס תליבח .7
דל תרואת .8
הבכ / קלדה גתמ .9
םילולכ םיראותמה וא םיריואמה םירזיבאה לכ אל *
.יטרדנטסה חולשמב
םיינכט םינותנ
WU172.9
WU172
WU172.1
WU172.A
20V
1+
m
10
10
30
1.0 1.3
1820
םירזיבא
WU172.A WU172.9 WU172.1 WU172
1 2
Ah
)
1 1 A2
)

HE
2
תוריש 6(
יאנכט י"ע ןתניהל ילמשחה הדובעה ילכל תורישה לע .א
.םיירוקמ ףוליח יקלחב שמתשמה ךמסומ
.םימוגפ תוללוס יזראמ ןקתל תוסנל ןיא .ב
החדקמ תוחיטב תרהזא
תולועפה לכל תוחיטב תוארוה1(
2
a
c
הללוסל תוחיטב תוארוה
.תוללוסה זראמ וא תוללוסה תא סורגל וא חותפל ,קרפל ןיא )א
תוללוס יזראמ ןסחאל ןיא .תוללוסה זראמ תא רצקל ןיא )ב
רצקל םילולע םה הבש הריגמב וא הספוקב ןכוסמ ןפואב
.םתוא רצקל םילולע םיכילומ םירמוחש וא הז תא הז
ןוסחאמ ענמיה .שאל וא םוחל תוללוסה זראמ תא ףושחל ןיא )ג
.רישי שמש רואל ףושח םוקמב
.תוללוסה זראמב תיזיפ העיגפ עונמל שי )ד
םע םילזונה לש עגמ רשפאל ןיא ,הללוס תפילד לש הרקמב )ה
רוזאה תא ףוטשל שי ,עגמ לש הרקמב .םייניעה וא רועה
.יאופר לופיטל תונפלו םימ לש תולודג תויומכב עוגנה
וא הללוס תעילב לש הרקמב יאופר לופיטל דימ תונפל שי )ו
.תוללוס זראמ
.שביו יקנ תוללוסה זראמ תא רומשל שי )ז
תילטמב םתוקנל שי ,םיכלכלתמ תוללוסה זראמ יקדה םא )ח
.הייקנו השבי
דיפקהל שי .שומישה ינפל תוללוסה זראמ תא ןועטל שי )ט
.ןוכנה הניעטה ךילהב שמתשהלו הלא תוארוה לע דימת
ישב וניא רשאכ הניעטב תוללוסה זראמ תא ריאשהל ןיא )י־
.שומ
ןועטל ךרוצ היהיש ןכתיי ,ןוסחא לש תוכשוממ תופוקת רחאל )אי
םיעוציב תגשהל םימעפ המכ תוללוסה זראמ תא קורפלו
.םייברמ
לעופ אוה רשאכ םייבטימ םיעוציב קפסמ תוללוסה זראמ )בי
.)20°C ± 5°C( הליגרה רדחה תרוטרפמטב
יזראמ הזמ הז דירפהל שי ,תוללוס יזראמ לש הכלשה תעב )גי
.תונוש תוימיכ-ורטקלא תוטישב םילעופה תוללוס
ידי-לע ןיוצמה ןעטמה תועצמאב קר שדחמ ןועטל שי )די
קפוסמה ןעטמה דבלמ ןעטמ םושב שמתשהל ןיא .WORX
.דויצה םע שומישל דחוימב
.דויצה םע שומישל דעונ אלש תוללוס זראמב שמתשהל ןיא )וט
.םידלי לש םדי גשיהמ תוללוסה זראמ תא קיחרהל שי )זט
.דיתעב ןויעל םיירוקמה רצומה יכמסמ תא רומשל שי )זי
.שומישב וניא רשאכ דויצהמ הללוסה תא איצוהל שי )חי
.הכלהכ ךילשהל שי )טי
םינוש גוס וא לדוג ,תלוביק ,רוציי לש תוללוס בברעל ןיא )כ
.ןקתהב
דע תירוקמה ותזיראהמ תוללוסה זראמ תא ריסת לא )אכ
.שרדייש
בהל ידכ הללוסה לע )-( סונימו )+( סולפ םינמיסל בל םיש )בכ־
.ןוכנ שומיש חיט
םילמס
.

HE
1
רצומה תוחיטב
ילכל תויללכ תוחיטב תוארוה
םיילמשח הדובע
,תוארוהה ,תוחיטבה תורהזא לכ תא אורקל שי :הרהזא
.הז הדובע ילכל םיפרוצמה םיטרפמהו םירויאה
.דיתעב ןויעל ,חוטב םוקמב תרבוחה תא ורמש
הדובעה רוזאב תוחיטב 1(
.בטיה ראומו יקנ הדובע רוזא לע ורמש .א
רקב ןוגכ ,תוציפנ תוביבסב םיילמשח הדובע ילכ וליעפת לא .ב־
.קבא וא םיזג ,םיקילד םילזונ תב
הדובע ילכ תלעפה תעב םירחא םישנאו םידלי וקיחרה .ג
.ילמשח
תילמשח תוחיטב 2(
םיעקשל םיאתהל םיילמשחה הדובעה ילכ יעקת לע .א
.איהש הרוצ לכב עקתה תא ונשת לא םלועל .םיילמשחה
הדובע ילכ רוביחל םהשלכ םיעקת ימאתמב ושמתשת לא
.םיקראומ םיילמשח
,תורוניצ ןוגכ ,םיקראומ םיחטשמ םע עגממ וענמיה .ב
.םיררקמו לושיב ירונת ,םירוטאידר
.תוחלל וא םשגל םיילמשחה הדובעה ילכ תא ופשחת לא .ג
לבכב ושמתשת לא םלועל .הניזה לבכ לע חוכ וליעפת לא .ד
תא וקיחרה .ילמשחה עקשהמ וקותינל וא ילכה תאישנל
.םיענ םיקלחמ וא םידח תווצקמ ,ןמשמ ,םוחמ לבכה
תעב הנבמל ץוחמ שומישל םיאתמה ךיראמ לבכב ושמתשה .ה
הנבמל ץוחמ ילמשח הדובע ילכ תלעפה.
ילכ תלעפהמ ענמיהל ןתינ אלשכ תחפ קספמב ושמתשה .ו
.החל הביבסב ילמשח הדובע
תישיא תוחיטב 3(
תעב ןויגיהב וגהנו םישוע םתאש המל בל ומיש ,םירע ויה .א
.ילמשח הדובע ילכ תלעפה
.ןגמ יפקשמ דימת ושבל .ישיא ןגמ דויצב ושמתשה .ב
ינפל יובכ בצמב גתמהש ואדו .היופצ יתלב הלעפה וענמ .ג
.ותאישנ וא ילכה תמרה ,הללוס וא/ו חתמ רוקמל ילכה רוביח
ילכ תלעפה ינפל םיגרב תוחתפמ וא ןונווכ תוחתפמ וריסה .ד
.ילמשחה הדובעה
דימת ורמש .םיקחורמ תומוקמל עיגהל תנמ לע וחתמתת לא .ה
.הביצי הדימע לע
.םיטישכת וא םייופר םידגב ושבלת לא .םאתהב ושבלתה .ו
םיקלח ןיבל םידגבהו רעישה ןיב קחרמ לע דיפקהל שי
.םיענ
םהש אדוול שי קבא באוש רוביחל םימאתמ םיקפוסמשכ .ז
.יוארכ םהב םישמתשמו בטיה םירבוחמ
ות םילכב ףוכת שומיש בקע תורכיה ובש בצממ ענמיהל שי .ח־
.םילכה לש תוחיטבה תונורקעמ תומלעתהלו תוננאשל ליב
הקוזחתו שומיש 4(
ילכב ושמתשה .ילמשחה הדובעה ילכ לע חוכ וליעפת לא .א
.המישמל םיאתמה ילמשחה הדובעה
ליעפמ וניא גתמה םא ילמשחה הדובעה ילכב ושמתשת לא .ב
.ותוא הבכמ וא
הללוסה תא ואיצוה וא/ו חתמה רוקממ עקתה תא וקתנ .ג
תפלחה ,םהשלכ םינוויכ עוציב ינפל ילמשחה הדובעה ילכמ
.ןוסחא וא םירזיבא
גשיהמ קחרה שומישב םניאש םיילמשח הדובע ילכ ונסחא .ד
פהב םיאיקב םניאש םישנאל ורשפאת לאו םידלי לש םדי־
.ותוא ליעפהל הלא תוארוהב וא ילמשחה הדובעה ילכ תלע
םיקלח רחא וקדב .םיניקת םיילמשח הדובע ילכ לע ורמש .ה
רחא יאנת לכו םירובש םיקלח ,םיפפוכמ וא םימוקע םיענ
וגאד .ילמשחה הדובעה ילכ תלועפ לע עיפשהל לולעה
.וב שומישה ינפל םוגפ ילמשח הדובע ילכ ןוקיתל
.םייקנו םידח ךותיח ילכ לע ורמש .ו
'דכו םיטיבב םירזיבאב ,ילמשחה הדובעה ילכב ושמתשה .ז
הדובעה יאנתב תובשחתה ךות ,הלא תוארוהל םאתהב
.עוציבל הדובעה תוהמבו
םייקנ ,םישבי הזיחאה יחטשמ לעו תוידיה לע רומשל שי .ח
.זירג וא ןמש אללו
ותקוזחתו הללוס לעפומ הדובע ילכב שומיש 5(
.דבלב ןרציה י"ע קפוסמה ןעטמה תועצמאב ונעט .א
.דבלב ול תודעוימה תוללוס םע הדובעה ילכב ושמתשה .ב
םייתכתמ םיצפחמ ,שומישב הניאשכ ,הללוסה תא וקיחרה .ג
םיגרב ,םירמסמ ,תוחתפמ ,תועבטמ ,ריינ יבטא ןוגכ םירחא
ןיב עגמ רוציל םילולעה ,םירחא םינטק םייתכתמ םיצפח וא
.הללוסה יבטוק ינש
;הנממ ףולדל לולע הללוסה לזונ םיינוציק שומיש יאנתב .ד
.גגושב עגמ לש הרקמב םימב דימ ופטש .עגממ וענמיה
.םייניעה םע עגמ לש הרקמב יאופר עויס תלבקל ונפ ,ףסונב
רבעש וא םגפנש ילכב וא תוללוס זראמב שמתשהל ןיא .ה
.םייוניש
ירח הרוטרפמטל וא שאל ילכ וא תוללוס זראמ ףושחל ןיא .ו־
130°C.הג
זראמ תא ןועטל ןיא .הניעטה תוארוה לכ לע דיפקהל שי .ז
ןיוצמה חווטהמ תגרוחה הרוטרפמטב ילכה וא תוללוסה
.תוארוהב

Copyright © 2020, Positec. All Rights Reserved.
AR01528400
www.worx.com
This manual suits for next models
3
Table of contents
Languages:
Other Worx Professional Drill manuals

Worx Professional
Worx Professional WU171 User manual

Worx Professional
Worx Professional WU189 User manual

Worx Professional
Worx Professional WU181PT User manual

Worx Professional
Worx Professional WU362 User manual

Worx Professional
Worx Professional WU303 User manual

Worx Professional
Worx Professional WU100 User manual

Worx Professional
Worx Professional WU362 User manual

Worx Professional
Worx Professional WU303 User manual