Worx WX045.X User manual

WX045 WX045.X

EN
D
F
I
ES
PT
NL
DK
NOR
SV
PL
GR
HU
RO
CZ
SK
SL
RU
Original instructions
Originalbetriebsanleitung
Notice originale
Istruzioni originali
Manual original
Manual original
Oorspronkelijke gebruiksaanwijzing
Original brugsanvisning
Opprinnelige Instruksjonene
Bruksanvisning i original
Instrukcja oryginalna
ΠΡΩΤΟΤΥΠΟ ΟΔΗΓΙΩΝ ΧΡΗΣΗΣ
Eredeti használati utasítás
Instrucţiuni originale
Původní návod k používání
Pôvodný návod na použitie
Izvirna navodila
Оригинальное руководство по эксплуатации
P06
P16
P27
P38
P49
P60
P71
P82
P92
P102
P112
P124
P136
P147
P158
P169
P180
P191
EN
D
F
I
ES
PT
NL
DK
NOR
SV
PL
GR
HU
RO
CZ
SK
SL
RU

1
2
34
5
6
7
8
9

1
2
A B
C D
E

6
EN
TABLE OF CONTENTS
1. PRODUCT SAFTY
2. COMPONENT LIST
3. TECHNICAL DATA
4. OPERATING INSTRUCTIONS
5. MAINTENANCE
6. ENVIRONMENTAL PROTECTION
7. DECLARATION OF CONFORMITY
8. TROUBLESHOOTING
1.PRODUCT SAFETY
GENERAL SAFETY WARNINGS
WARNING Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in

SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or men-
tal capabilities or lack of experience and
knowledge if they have been given super-
vision or instruction concerning use of the
appliance in a safe way and understand
the hazards involved. Children shall not

7
EN
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
WARNING: For the purposes of re-
charging the battery, only use the de-
tachable supply unit provided with this appli-
ance.
ADDITIONAL SAFETY INSTRUCTIONS
FOR GLUE GUNS

with care, therefore
– be careful when using the appliance
in places where there are combustible
materials;
– do not apply to the same place for a long
time;
– do not use in presence of an explosive
atmosphere;
– be aware that heat may be conducted to
combustible materials that are out of sight;
– place the appliance on its stand after use
and allow it to cool down before storage;
– do not leave the appliance unattended when
it is switched on.

8
EN
SAFETY WARNINGS FOR BATTERY PACK
a)Do not dismantle, open or shred cells or
battery pack.
b)Do not short-circuit a battery pack. Do not
store battery packs haphazardly in a box or
drawer where they may short-circuit each
other or be short-circuited by conductive
materials. When battery pack is not in use,

paper clips, coins, keys, nails, screws or

connection from one terminal to another.
Shorting the battery terminals together may

c) Do not expose battery pack to heat or re.
Avoid storage in direct sunlight.
d)Do not subject battery pack to mechanical
shock.
e)In the event of battery leaking, do not allow
the liquid to come into contact with the
skin or eyes. If contact has been made,
wash the affected area with copious
amounts of water and seek medical advice.
f) Keep battery pack clean and dry.
g)Wipe the battery pack terminals with a
clean dry cloth if they become dirty.

9
EN
h)Battery pack needs to be charged before
use. Always refer to this instruction and
use the correct charging procedure.
i) Do not maintain battery pack on charge
when not in use.
j) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
k)Recharge only with the charger specied
by Worx. Do not use any charger other than
that specically provided for use with the
equipment.
l) Do not use any battery pack which is not
designed for use with the equipment.
m)Keep battery pack out of the reach of
children.
n)Retain the original product literature for
future reference.
o)Remove the battery from the equipment
when not in use.
p)Dispose of properly.
q)Do not mix cells of different manufacture,
capacity, size or type within a device.
r) Keep the battery away from microwaves
and high pressure.

10
EN
SYMBOLS
Read operator’s manual
Warning
Wear eye protection
Wear protective gloves
Do not burn
Batteries may enter water cycle if disposed improperly, which can
be hazardous for ecosystem. Do not dispose of waste batteries as
unsorted municipal waste.
Li-I on
Li-Ion battery. This product has been marked with a symbol
relating to ‘separate collection’ for all battery packs and battery
pack. It will then be recycled or dismantled in order to reduce
the impact on the environment. Battery packs can be hazardous
for the environment and for human health since they contain
hazardous substances.
Waste electrical products must not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authorities or retailer for recycling advice.
2. COMPONENT LIST
1. GLUE STICK HOLE
2. NOZZLE
3. HEATING INDICATOR
4. ON/OFF SWITCH
5. SWITCH TRIGGER
6. BATTERY PACK RELEASE BUTTON *

11
EN
7. BATTERY PACK *
8. GLUE STICK
9. GLUE STICK CHAMBER
* Not all the accessories illustrated or described are included in standard
delivery.
3.TECHNICAL DATA
Type WX045 WX045.X (045- designation of machinery, representative of
glue gun)
WX045 WX045.X **
Rated voltage 20 V Max. ***
Glue Stick Diameter 11mm
Nozzle Caliber 3 mm
Preheating Time 3 mins
Temperature when heated 200 °C
Machine weight (bare tool) 0.36 kg
** X=1-999, A-Z, M1-M9 there are only used for different customers, there are no safe
relevant changes between these models.
*** Voltage measured without workload. Initial battery voltage reaches maximum of
20 volts. Nominal voltage is 18 volts.
SUGGESTED BATTERIES AND CHARGERS
Category Model Capacity
20V Battery WA3551 2.0Ah
20V Charger WA3760 0.4A
We recommend that you purchase your accessories from the same store that
sold you the tool. Refer to the accessory packaging for further details. Store
personnel can assist you and offer advice.

12
EN
4. OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction book carefully.
INTENDED USE
The tool can be used for bonding wood, leather, plastics ,papers and other
materials.
OPERATION
ACTION FIGURE
Inserting or removing the battery pack See Fig. A
Charging the battery pack See Fig. B
Insert the glue stick into the glue stick hole See Fig. C

The heat indicator light will be red as it heats and will turn green
when it is ready to use. See Fig. D
Press the switch trigger for gluing
NOTE: It is recommended to apply the glue on large surfaces

apply in lines.
WARNING: Do not allow the hot glue or the nozzle tip
to come into contact with persons or animals.If hot
glue contacts with the skin, do not try to remove the glue
from the skin,but put the affected area immediately under a
stream of cold water for several minutes.
See Fig. E
5.MAINTENANCE
Remove the battery before carrying out any adjustment, servicing or
maintenance.
There are no user serviceable parts in your power tool. Never use water or
chemical cleaners to clean your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust. Occasionally you may see sparks
through the ventilation slots. This is normal and will not damage your power
tool.Store the accessories in a dry place.
Warning: Do not use inflammable solvents for cleaning the surfaces to be
glued. For excess hardened glue, it can be removed with a blunt object. Do
not use solvent for cleaning.

13
EN
6. ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
authorities or retailer for recycling advice.
7.DECLARATION OF CONFORMITY
We,
Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
On behalf of Positec declare that the product
Description 20V Cordless Full Size Hot Glue Gun
Type Designation WX045 WX045.X (045-designation of machinery,
representative of glue gun)
Function Gluing
Complies with the following directives,
2014/30/EU, 2011/65/EU & (EU)2015/863
Standards conform to
EN 60335-1, EN 60335-2-45
EN 62233, EN 55014-1, EN 55014-2

Name Marcel Filz
Address Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany

Allen Ding

Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China

14
EN
8.TROUBLESHOOTING
Problems Possible Causes Possible Solution
No glue comes out Glue stick is used up.
Glue stick diameter is too
large or small.
Glue stick is not pushed
to the end.
Insert a new glue stick.
Use recommended glue
sticks.
Push the glue stick to
the end when loading.
Glue stick falls out
from the tool. Glue stick diameter is too small. Use recommended glue sticks.
There is glue leaking
out without trigger
pressed after use.
The temperature is still
high in short time after
use and will cause glue
melted.
It is normal and will stop
leaking out when the
glue gun cools down.
Trigger is blocked for
glue escaping toward
the rear.
Glue stick diameter too
small.
Glue stick’s melting
temperature is too low.
Use recommended glue
sticks.
Glue does not flow
evenly. Glue stick’s melting temperature is too low.
Glue is not heated long
enough.
Trigger is not pressed
uniformly.
Wait for heating.
Allow the glue gun time
to heat up.
Press trigger slowly and
uniformly.
Adhesive surface only
bonds on one side. Adhesive already partially has cooled off before
work-pieces have been
bonded.
Bond work-pieces in a
quicker way.
Set gluing points instead
of applying glue over
surface.
Adhesive bond
doesn’t work after
cooling.
Surface is greasy or too
smooth.
Surface is dusty.
Unsuitable material or
work-piece.
Roughen adhesive
surface slightly.
Clean the surface.
Use specialized
adhesive.
Glued tiles in moist
locations are not
adhesive.
Moisture spreads under
bonding parts. Suggest to use specialized adhensive
suitable for moist
locations
Glued shoe soles are
not adhesive. Moisture causes leather to puff up and creeps
under bonding location.
Use specialized
adhesive.

15
EN
Strands are pulled
out when removing
the glue gun from the
work-piece.
Trigger is still pressed
after operation.
Nozzle has not been
wiped off.
Discontinue pressing
trigger before
completing the
operation.
Wipe off nozzle.
Work-piece melts. Work-piece contains
material that melts at a
low temperature.
Use specialized
adhesive.
Burns on fingers when
applying adhesive. Adhesive penetrates 
tissue
Do not hold work-piece
in hand.
Apply adhesive with
work-piece placed on
heat-resistant silicone
pad or base.
Metal work-piece has
heated up. Do not hold work-piece in hand.
Apply adhesive with
work-piece placed on
heat-resistant silicone
pad or base.
Clamp work-piece.

16
D
INHALTSVERZEICHNIS
1. PRODUKTSICHERHEIT
2. KOMPONENTEN
3. TECHNISCHE DATEN
4. HINWEISE ZUM BETRIEB
5. WARTUNG
6. UMWELTSCHUTZ
7. KONFORMITÄTSERKLÄRUNG
8. PROBLEMBEHEBUNG
1.SICHERHEITSVORSCHRIFTEN
SICHERHEITSHINWEISE
WARNUNG: Lesen Sie alle
Sicherheitshinweise und Anweisungen.
Eine Missachtung der nachstehenden

oder Verletzungen nach sich ziehen.
Bewahren Sie alle Sicherheitshinweise und
Anweisungen für die Zukunft auf.
Dieses Gerät kann von Kindern ab 8 Jahren
und Personen mit verringerten physischen,
sensorischen oder mentalen Fähigkeiten
bzw. Mangel an Erfahrung oder Kenntnis
verwendet werden, wenn sie von einer
Person beaufsichtigt oder bezüglich des
Gebrauchs des Gerätes in einer sicheren

17
D
Umgebung unterwiesen werden und die damit
verbundenen Gefahren verstehen. Kinder
sollten mit dem Gerät nicht spielen und
Reinigungs- und Wartungsarbeiten nur unter
Aufsicht durchführen.
WARNUNG: Verwenden Sie zum
Auaden des Akkus ausschließlich die
diesem Gerät beiliegende, abnehmbare
Stromversorgungseinheit.
ZUSÄTZLICHE SICHERHEITSHINWEISE
FÜR HEISSKLEBEPISTOLEN
Bei unvorsichtiger Handhabung des Gerätes
kann
ein Brand entstehen, deshalb
- Seien Sie vorsichtig, wenn Sie dieses
Gerät an Orten verwenden, an denen sich
entzündbare Substanzen.
- Gerät nicht für längere Zeit auf ein und
dieselbe Stelle richten.
- Nicht in der Nähe leicht entzündbarer Gase
oder Materialien arbeiten.
- Wärme kann zu brennbaren Teilen
gelangen, die sich außer Sichtweite

- Gerät vor der Aufbewahrung vollständig
abkühlen lassen.

18
D
- Gerät nicht unbeaufsichtigt betreiben.
SICHERHEIT HINWEISE FÜR AKKUPACK
a)Zellen bzw. Akkupack nicht zerlegen,
öffnen oder zerdrücken.
b)Akkupack nicht kurzschließen.
Akkupacks nicht wahllos in einer
Schachtel oder Schublade aufbewahren,
wo sie einander kurzschließen oder
durch andere leitfähige Materialien
kurzgeschlossen werden könnten.
Bei Nichtverwendung des Akkupacks
ist dieses von Metallgegenständen
fernzuhalten, wie etwa Büroklammern,
Münzen, Nägeln, Schrauben oder anderen
kleinen Metallgegenständen, wo sich
die Batterieklemmen berühren könnten.
Das Kurzschließen der Batterieklemmen
kann Verbrennungen bzw. einen Brand
verursachen.
c)Zellen bzw. Akkupacks nicht Hitze oder
Feuer aussetzen. Lagerung in direktem
Sonnenlicht vermeiden.
d)Akkupack nicht mechanischen Stößen
aussetzen.
e)Im Fall, dass Flüssigkeit aus dem Akku
austritt, darf diese nicht in Kontakt mit

19
D
der Haut oder den Augen kommen. Sollte
dies dennoch geschehen, den betroffenen
Bereich sofort mit viel Wasser spülen und
einen Arzt aufsuchen.
f) Akkupack sauber und trocken halten.
g)Sollten die Klemmen des Akkupacks
schmutzig werden, diese mit einem
sauberen, trockenen Tuch abwischen.
h)Akkupackmuss vor Gebrauch aufgeladen
werden. Immer dieses Anweisungen
beachten und den korrekten Ladevorgang
ausführen.
i) Akkupack bei Nichtverwendung nicht
längere Zeit auaden lassen.
j) Nach längerer Lagerung des Gerätes ist
es eventuell notwendig, die Zellen oder
das Akkupack mehrere Male aufzuladen
und zu entladen, um eine optimale
Leistung zu erhalten.
k)Nur mit dem von Worx bezeichneten
Ladegerät auaden. Kein Ladegerät
verwenden, das nicht ausdrücklich für
den Gebrauch mit dem Gerät vorgesehen
ist.
l) Kein Akkupack verwenden, das nicht für
den Gebrauch mit dem Gerät vorgesehen

20
D
ist.
m)Akkupacks von Kindern fernhalten.
n)Die originalen Produktunterlagen zum
späteren Nachschlagen aufbewahren.
o)Den Akku bei Nichtverwendung aus dem
Gerät nehmen.
p)Ordnungsgemäß entsorgen.
q)Vermischen Sie keine Zellen
verschiedener Hersteller, Kapazitäten,
Größen oder Typen innerhalb eines
Geräts.
r) Halten Sie den Akku von Mikrowellen und
hohem Druck fern.
SYMBOLE
Bedienungsanleitung lesen
Warnung
Tragen Sie eine Schutzbrille
Schutzhandschuhe tragen
Nicht verbrennen
Wenn die Akkus unsachgemäß behandelt wird, können sie in
den Wasserkreislauf gelangen und das Ökosystem schädigen.
Entsorgen Sie verbrauchte Akkus nicht über den Hausmüll.