Woxcon MUH44E-H2 KIT User manual

MUH44E-H2 KIT
4K 4x4 HDBaseT Matrix with 3 Receivers
All Rights Reserved
Version: MUH44E-H2 KIT_2019V1.1
User Manual

4K 4x4 HDBaseT Matrix with 3 Receivers
Preface
Read this user manual carefully before using the product. Pictures shown in this
manual are for reference only. Different models and specifications are subject to real
product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till
September, 2019. In the constant effort to improve the product, we reserve the right to
make functions or parameters changes without notice or obligation. Please refer to the
dealers for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at their own expense will be required to take whatever measures
may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

4K 4x4 HDBaseT Matrix with 3 Receivers
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
l Unpack the equipment carefully and save the original box and packing material for
possible future shipment
l Follow basic safety precautions to reduce the risk of fire, electrical shock and
injury to persons.
l Do not dismantle the housing or modify the module. It may result in electrical
shock or burn.
l Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
l Refer all servicing to qualified service personnel.
l To prevent f i r e o r shock hazard, do not e x p o s e t h e u n i t to rain, moi s t u r e o r install
this product near water.
l Do not put any heavy items on the extension cable in case of extrusion.
l Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
l Install the device in a place with fine ventilation to avoid damage caused by
overheat.
l Keep the module away from liquids.
l Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module
immediately.
l Do not twist or pull by force ends of the cable. It can cause malfunction.
l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
l Unplug the power cord when left unused for a long period of time.
l Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

4K 4x4 HDBaseT Matrix with 3 Receivers
Table of Contents
1. Product Introduction .................................................................................................... 1
1.1 Features ............................................................................................................. 1
1.2 Package List ....................................................................................................... 2
2. Specification ................................................................................................................ 3
2.1 MUH44E-H2 HDBaseT Matrix ............................................................................ 3
2.2 TPUH-BYE20R HDBaseT Receiver ................................................................... 4
3. Panel Description ........................................................................................................ 5
3.1 Matrix Front Panel .............................................................................................. 5
3.2 Matrix Rear Panel ............................................................................................... 5
3.3 Receiver Front and Rear Panel .......................................................................... 6
4. System Connection ..................................................................................................... 7
4.1 Usage Precaution ............................................................................................... 7
4.2 System Diagram ................................................................................................. 7
5. Panel Control ............................................................................................................... 8
5.1 Signal Switching ................................................................................................. 8
5.2 EDID Setting ....................................................................................................... 8
6. IR Control .................................................................................................................... 9
6.1 IR Remote Control .............................................................................................. 9
6.2 IR Pass-through Control ................................................................................... 10
6.2.1 Control Far-end Device locally ............................................................... 10
6.2.2 Control Local Device Remotely .............................................................. 10
7. GUI Control ................................................................................................................ 13
7.1 Switching Tab ................................................................................................... 14
7.2 Audio Tab .......................................................................................................... 15
7.3 Configuration Tab ............................................................................................. 16
7.3.1 PoC Setting ............................................................................................ 16
7.3.2 EDID Copy ............................................................................................. 16
7.3.3 EDID Setting .......................................................................................... 17
7.4 RS232 Tab ........................................................................................................ 18
7.5 Access Tab ....................................................................................................... 19

4K 4x4 HDBaseT Matrix with 3 Receivers
7.6 Interface Tab ..................................................................................................... 20
7.7 Network Tab ...................................................................................................... 21
7.8 GUI Upgrade .................................................................................................... 22
8. RS232 Control ........................................................................................................... 23
8.1 RS232 Control Software ................................................................................... 23
8.2 RS232 Communication Command ................................................................... 25
8.2.1 Device Control ........................................................................................ 25
8.2.2 Source Switching ................................................................................... 26
8.2.3 Preset Setting ......................................................................................... 26
8.2.4 Audio Control .......................................................................................... 27
8.2.5 EDID Management ................................................................................. 27
8.2.6 HDCP Management ............................................................................... 30
8.2.7 Third-party Device Control ..................................................................... 31
9. Panel Drawing ........................................................................................................... 32
10. Troubleshooting and Maintenance .......................................................................... 33
11. Customer Service .................................................................................................... 35

4K 4x4 HDBaseT Matrix with 3 Receivers
1
1. Product Introduction
Thanks for choosing this 4K 4x4 HDBaseT Matrix with 3 Receivers! It features 4 HDMI
inputs, 1 HDMI output with audio breakout and 3 HDBaseT outputs. The de-embedded
audio can be output from SPDIF and L/R connector. It supports video resolutions up to
4K@60Hz 4:4:4 and can transmit 4K video to distances up to 131 feet (40 meters) and
1080P video to distances up to 229 feet (70 meters) over a single CATx cable. It
supports bidirectional IR extension and IR, RS232, and TCP/IP control options. It
supports the Power over Cable (PoC) feature, allowing the receivers to draw their
power from the matrix over the CATx cable. In addition, there is the smart built-in EDID
setting can be selected by the 4-pin DIP switch on the rear panel.
1.1 Features
l Supports HDMI resolutions up to 4K@60Hz 4:4:4, including 1080P 3D video
l Fully compliant with the HDMI 2.0 and HDCP 2.2 specifications
l Can transmit 4K signals to distances up to 131 feet (40 meters) and 1080P signals to
distances up to 229 feet (70 meters) over a single CATx cable.
l Features three HDBaseT outputs and includes three receivers.
l Supports the 24V PoC feature, allowing the receivers to draw their power from the
matrix over the CATx cable.
l Includes a local HDMI output with corresponding digital optical S/PDIF and stereo
L/R analog outputs.
l Smart EDID management for various application and customized setting.
l Controllable via RS232, IR and TCP/IP.

4K 4x4 HDBaseT Matrix with 3 Receivers
2
1.2 Package List
HDBaseT Matrix
l 1x MUH44E-H2 4K 4x4 HDBaseT Matrix
l 2x Mounting Ears with 6 Screws
l 4x Plastic Cushions
l 1x IR Remote
l 4x IR Receivers
l 4x IR Emitters
l 1x RS232 Cable (3-pin to DB9)
l 1x 5-pin Terminal Bl o c k
l 1x Power Adaptor (24V DC 2.71A)
l 1x Power Cord
HDBaseT
Receiver
l 3x TPUH-BYE20R HDBaseT Receivers
l 6x Mounting Ears with 6 Screws
l 1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

4K 4x4 HDBaseT Matrix with 3 Receivers
3
2. Specification
2.1 MUH44E-H2 HDBaseT Matrix
Video
Video Input
(4) HDMI
Video Input Connector
(4) Type-A female HDMI
Video input Video Resolution
Up to 4K@60Hz 4:4:4
Video Output
(3) HDBaseT, (1) HDMI
Video Output Connector
(3) RJ45, (1) Type-A Female HDMI,
Video output Video Resolution
HDMI: Up to 4K@60Hz 4:4:4
HDBaseT: Up to 4K@60Hz 4:4:4
HDMI Version
Up to 2.0
HDCP Version
Up to 2.2
HDMI Audio Signal
LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, Dolby Digital®
Plus, DTS:X™, and DTS-HD® Master Audio™ pass-through.
Audio
Audio Output
(1) SPDIF, (1) L/R
Audio Output Connector
(1) Tos li nk c on ne ct or s, (1) 5-pin terminal blocks
Frequency Response
20Hz – 20kHz, ±3dB
Max Output Level
2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV)
nominal consumer line level signal
THD+N
< 0.05% (-80dB), 20Hz – 20kHz bandwidth, 1kHz sine at 0dBFS level
(or max level)
SNR
> 80dB, 20Hz - 20kHz bandwidth
Crosstalk Isolation
> 70dB, 10kHz sine at 0dBFS level (or max level before clipping)
L-R Level Deviation
< 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping)
Frequency Response Deviation
< ± 0.5dB 20Hz - 20kHz
Output Load Capability
1KΩ and higher (Supports 10x paralleled 10KΩ loads)
Stereo Channel Separation
>70dB@1kHz
Control
Control Port
(1) FIRMWARE, (3) IR IN, (1) IR EYE, (4) IR OUT, (1) TCP/IP,
(1) RS232, (1) EDID
Control Connector
(1) Micro-USB, (8) 3.5mm jacks, (1) RJ45, (1) 3-pin terminal block,
(1) 4-pin DIP switch
General
Transmission Standard
HDBaseT
Transmission Distance
1080P@60Hz ≤ 230 feet (70 meters),

4K 4x4 HDBaseT Matrix with 3 Receivers
4
4K@60Hz ≤ 131 feet (40 meters)
Bandwidth
18Gbps
Operation Temperature
-5~ +55℃
Storage Temperature
-25 ~ +70℃
Relative Humidity
10%-90%
External Power Supply
Input: AC 100~240V, 50/60Hz; Output: 24V DC 2.71A
Maximum Power Consumption
58watts
Dimension (W*H*D)
436.4mm x 44mm x 236.5mm
Net Weight
1.9KG
2.2 TPUH-BYE20R HDBaseT Receiver
Receiver
Input
(1) HDBT
Input Connector
(1) RJ45
Output
(1) HDMI
Output Connector
(1) Female type-A HDMI
Control
(1) IR IN, (1) IR OUT
Control Connector
(2) 3.5mm mini jacks
General
Video Resolution
Up to 4K@60Hz 4:4:4
Transmission Mode
HDBaseT
Transmission Distance
1080P@60Hz ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)
HDMI Version
Up to 2.0
HDCP Version
Up to 2.2
Bandwidth
18Gbps
Power Consumption
9.5W (Max)
Operating Temperature
-5℃ ~ +55℃
Storage Temperature
-25℃ ~ +70℃
Relative Humidity
10%-90%
Power Supply
Input Power: 24V DC 1.25A or Power over Cable (PoC)，
AC Adaptor Input Power: 100~240VAC, 50/60Hz
Dimension (W*H*D)
74mm x 18mm x 120mm
Net Weight (g)
235g

4K 4x4 HDBaseT Matrix with 3 Receivers
5
3. Panel Description
3.1 Matrix Front Panel
①
FIRMWARE: Micro-USB port for firmware upgrade.
②
Power LED: The LED illuminates red when power is applied.
③
Signal Switching Zone:
A. INPUT LEDs: A series of four LEDs, one of which illuminates blue to indicate
which source is selected.
B. OUTPUT button: Press the button repeatedly to cycle through the four video
inputs.
④
PRESET RECALL:
l Press and hold the button 1~3 to save the current switching status to the
corresponding preset 1~3.
l Press the button 1~3 to recall the saved preset 1~3.
3.2 Matrix Rear Panel
①
INPUTS: Four type-A female HDMI ports to connect the HDMI source devices
(Blu-ray Disc™ or DVD players, gaming consoles, etc.).
②
IR IN: Three 3.5mm jacks to connect the IR receivers for IR pass-through.
③
IR EYE: 3.5mm jack to connect the IR receiver for IR local control.
④
IR OUT: Four 3.5mm jacks to connect the IR emitters for IR pass-through.
12 3 4
AB
4
123567

4K 4x4 HDBaseT Matrix with 3 Receivers
6
⑤
OUTPUTS:
l 1~3-HDBT: Three HDBaseT RJ45 outputs to connect the three HDBaseT
receivers.
l 4-HDMI: One local HDMI port to connect a local display.
l SPDIF: A digital optical S/PDIF audio output.
l L/R: A stereo pair of analog RCA audio output jacks.
⑥
CONTROL:
l TCP/IP: RJ45 port to connect the control device (e.g. PC) to control the matrix
by GUI.
l RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or
a device to be controlled by RS232 commands.
l EDID: 4-pin DIP switch for EDID setting.
⑦
POWER: DC barrel connector for the power adapter connection.
3.3 Receiver Front and Rear Panel
①
HDMI Out: Type-A female HDMI port to connect the display device.
②
IR IN: 3.5mm jack to connect the IR receiver for IR pass-through.
③
IR OUT: 3.5mm jack to connect the IR emitter for IR pass-through.
④
HDBT In: RJ45 port to connect the HDBT output port of HDBaseT matrix by CATx
Ethernet cable. The LINK LED illuminates orange when there is a valid HDBaseT
link between the matrix and the receiver. The HDCP LED illuminates green when
the video contains HDCP content.
⑤
POWER LED: The LED illuminates red when power is applied.
⑥
DC 24V: DC barrel connector for the power adapter connection.
IR O ut
IR InHDM I O ut DC 2 4VHDBT In
123456

4K 4x4 HDBaseT Matrix with 3 Receivers
7
4. System Connection
4.1 Usage Precaution
l Make sure all components and accessories included before installation.
l System should be installed in a clean environment with proper temperature and
humidity.
l All of the power switches, plugs, sockets, and power cords should be insulated and
safe.
l All devices should be connected before power on.
4.2 System Diagram
HDMI 1 HDMI 2 HDMI 3 HDMI 4 1-HDBT
IR OUT
IR EYE
2-HDBT SPDIF4-HDMI3-HDBT DC 24V TCP/IP
RxTx
RS232
POWER CONT ROL IR IN OUTP UTS INPU TS
1 2 3
41 2 3
L R
1 2 3 4
ON DIP
EDID
On
Off
1
0
PS4
Game Console
Laptop
Blu Ray -
IR Emitter
IR
Emitter
Re cei v er
4K TV
IR
Receiver
Soundbar PC
HDMI:
HDBaseT:
IR:
AUDIO:
RS232:
TCP/IP:

4K 4x4 HDBaseT Matrix with 3 Receivers
8
5. Panel Control
5.1 Signal Switching
l Repeatedly press the OUTPUT button on front panel to cycle through the various
inputs for the corresponding output.
l Press and hold PRESET RECALL button 1~3 to save the current switching status to
the corresponding preset 1~3.
l Press the PRESET RECALL button 1~3 to recall the saved preset 1~3.
5.2 EDID Setting
The Extended Display Identification Data (EDID) is used for the source device to
match its video resolution with the connected display. By default, the EDID of source
device is 1080P PCM 2CH. Meanwhile, since the displays with different capabilities
are connected to the matrix, the 4-pin DIP switch on the rear panel can be used to set
the EDID to a built-in fixed value. Use the following table to determine the setting for
the 4-pin DIP switch for specific video resolution and audio capabilities. The switch
represents “0” when in the lower (Off) position, and it represents “1” while putting the
switch in the upper (On) position.
Switch Status
Video Resolution
Audio Format
0000 (Default)
Enable RS232, GUI or IR remote EDID management.
0001
1080P
2CH
0010
1080P
Multi-CH
0011
4K@30Hz HD
2CH
0100
4K@30Hz HDR
Multi-CH
0101
4K@60Hz HDR
2CH
0110
4K@60Hz HDR
Multi-CH
0111
User-define
Note:
l 2CH: LPCM 2Ch.
l Multi-CH: 8Ch LPCM, Dolby TrueHD, DTS-HD, Dolby Digital5.1, DTS 5.1, Dolby
Digital Plus.

4K 4x4 HDBaseT Matrix with 3 Receivers
9
6. IR Control
6.1 IR Remote Control
Connect IR receiver to the IR EYE port, the matrix can be controlled by the below IR
remote.
l Press the STANDBY (1) button to enter or exit standby
mode.
l To swi t c h t h e selected input for o n e o r mo re of the
outputs, first press the number corresponding to the
desired INPUT (2), then press one or more OUTPUTS (3)
or the ALL (4) button, then press the ENTER (4) button to
execute the change.
l Examples:
ü To send i n p u t 3 t o output 2, fi r s t p r ess the INPUTS 3
button, then press the OUTPUTS 2 button, and finally
press the ENTER button to execute the change.
ü To send i n p u t 1 t o outputs 1 and 4, f i r s t press the
INPUTS 1 button, then press both the OUTPUTS 1
and 4 buttons, and finally press the ENTER button to
execute the change.
ü To send i n p u t 4 to a l l o u t p u t s, f i r st p r e s s the INPUTS 4
button, then press the ALL button, and finally press
the ENTER button to execute the change.
l To set t h e E D I D for one or more source d e v i c e s t o the
EDID capabilities of a specific output, press the EDID (4)
button, then press the desired INPUTS (2) or the ALL (4)
button, then press the OUTPUTS (3) button
corresponding to the desired display, finally press the
ENTER (4) button to execute the operation.
INPUTS
OUTPUTS
MENU
1 2
34
1 2
34
ALL EDID
CLEAR ENTER
1
2
3
4

4K 4x4 HDBaseT Matrix with 3 Receivers
10
6.2 IR Pass-through Control
6.2.1 Control Far-end Device locally
Connect an IR receiver to IR IN port of the matrix; users can control far-end display via
its IR remote from local.
In that case, the IR signal is transferred via twisted pair. Only the corresponding IR
OUT port can emit control signals to the remote display.
See the figure below:
6.2.2 Control Local Device Remotely
Connect IR receiver(s) to IR IN ports on far-end HDBT receiver(s), and IR emitter(s) to
IR OUT ports of the matrix, and use the IR remote of local source to control the device
remotely.
l One to One:
Connect an IR receiver to IR IN port on far-end HDBaseT receiver, and an IR
emitter to IR OUT 1 port of the matrix. Use the IR remote of local source to control
the device remotely. See below:
HDMI 1 HDMI 2 HDMI 3 HDMI 4 1-HDBT
IR OUT
IR EY E
2-HDBT SPDIF4-HDMI
3-HDBT DC 24 V TCP/IP
RxTx
RS232
POWER CONTROL IR IN OUTPUTS INPUTS
1 2 3
4
1 2 3
L R
1 2 3 4
ON DIP
EDID
On
Off
1
0
IR
Emitter
IR
Receiver
Blu Ray -
Receiver
HDMI:
HDBaseT:
IR:
AUDIO:
RS232:
TCP/IP:

4K 4x4 HDBaseT Matrix with 3 Receivers
11
l Multiple to One:
If switch HDMI 1 to all HDBT outputs, connect three IR receivers to IR IN ports of
HDBaseT receivers, and an IR emitter to IR OUT 1 port of the matrix. See below:
HDM I 1 HDMI 2 HDM I 3 HDMI 4 1-HDBT
IR OUT
IR EYE
2-HDBT SPDIF4-HDMI
3-HDBT DC 24V TCP/IP
RxTx
RS232
POWER CONTROL IR IN O UTPUT S INP UTS
1 2 3
41 2 3
L R
1 2 3 4
ON DIP
EDID
On
Off
1
0
IR
Emitter
Re c e i v er
IR
Receiver
HDMI:
HDBaseT:
IR:
AUDIO:
RS232:
TCP/IP:
Blu Ray -
HDMI 1 HDMI 2 HDMI 3 HDMI 4 1-HDBT
IR OUT
IR EYE
2-HDBT SPDIF4-HDMI3-HDBT DC 24V TCP/IP
RxTx
RS232
POWER CONT ROL IR IN OUTP UTS INPU TS
1 2 3
41 2 3
L R
1 2 3 4
ON DIP
EDID
On
Off
1
0
Re c eiv e r
IR
Receiver
Re c eiv e r
IR
Receiver
IR
Emitter
HDMI:
HDBaseT:
IR:
AUDIO:
RS232:
TCP/IP:
Re c eiv e r
IR
Receiver
Blu Ray -

4K 4x4 HDBaseT Matrix with 3 Receivers
12
The IR signal can be sent by any three of IR remotes, then it is transferred to
HDBaseT receiver, then to IR OUT 1 port and received by the local source device.
Switching Operation:
Sending command (reference to 8.2.2 Source Switching):
Command
Description
IRFollowON.
Enable the IR switching to follow video switching.
IRFollowOFF.
Disable the IR switching to follow video switching.
IR[X]:[Y].
Switch local IR OUT [X] to far-end IR IN [Y]. x=1~4, Y=1~3.

4K 4x4 HDBaseT Matrix with 3 Receivers
13
7. GUI Control
The matrix can be controlled via TCP/IP. The default IP settings are:
IP Address:
192.168.0.178
Subnet Mask:
255.255.255.0
Gateway:
192.168.0.1
Type 192.168.0.178 in the internet browser, it will enter the below log-in webpage:
Username: admin
Password: admin
Type the user name and password, and then click Login to enter the section for video
switching.

4K 4x4 HDBaseT Matrix with 3 Receivers
14
7.1 Switching Tab
Use the 4x4 button grid on the left side to set which inputs are directed to which
outputs. For example, clicking the buttons on the Input 1 row and Output 1,2,3,4
column, directs input 1 to all outputs.
Use the 6 numbered buttons on the right in conjunction with the Save and Recall
buttons to save and load layout presets.
l To save a g i v e n layout, first click one of the numbered buttons, then click the Save
button.
l To l o a d a p r e v i ously saved layout, f i r s t click one of t h e n u m b e r e d b u t tons, then
click the Recall button.

4K 4x4 HDBaseT Matrix with 3 Receivers
15
7.2 Audio Tab
l Turn on or turn off the analog audio output and digital audio output.