Woxcon MUH88T-H2 KIT User manual

MUH88T-H2 KIT
8x8 HDMI 2.0 HDBaseT Matrix Switcher with
8 Receivers
All Rights Reserved
Version: MUH88T-H2 KIT_2019V1.3
User Manual

8x8 HDMI 2.0 HDBaseT Matrix Switcher
Preface
Read this user manual carefully before using the product. Pictures shown in this
manual are for reference only. Different models and specifications are subject to real
product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till
November, 2019. In the constant effort to improve the product, we reserve the right to
make functions or parameters changes without notice or obligation. Please refer to the
dealers for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

8x8 HDMI 2.0 HDBaseT Matrix Switcher
SAFETY PRECAUTIONS
To ensure the best performance from the product, please read all instructions carefully
before using the device. Save this manual for further reference.
l Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
l Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
l Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
l Using supplies or parts not meeting the specifications of product may cause
damage, deterioration or malfunction.
l Refer all servicing to qualified service personnel.
l To prev ent fire or sh ock haz ard , do not exp ose the uni t to r ain, moi sture or inst all
this product near water.
l Do not put any heavy items on the extension cable in case of extrusion.
l Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
l Install the device in a place with fine ventilation to avoid damage caused by
overheat.
l Keep the module away from liquids.
l Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module immediately.
l Do not twist or pull by force ends of the optical cable. It can cause malfunction.
l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
l Unplug the power cord when left unused for a long period of time.
l Information on disposal for scrapped devices: do not burn or mix with general
household waste, and please treat them as normal electrical wastes.

8x8 HDMI 2.0 HDBaseT Matrix Switcher
Table of Contents
1. Product Introduction .................................................................................................... 1
1.1 Features ............................................................................................................. 1
1.2 Package List ....................................................................................................... 2
2. Specification ................................................................................................................ 3
2.1 Matrix Switcher ................................................................................................... 3
2.2 HDBaseT Receiver ............................................................................................. 4
3. Panel Description ........................................................................................................ 6
3.1 Matrix Switcher Front Panel ............................................................................... 6
3.2 Matrix Switcher Rear Panel ................................................................................ 7
3.3 Receiver Front and Rear Panel .......................................................................... 8
4. System Connection ................................................................................................... 10
4.1 Usage Precaution ............................................................................................. 10
4.2 System Diagram ............................................................................................... 10
5. Button Control ............................................................................................................ 11
5.1 Signal Switching ............................................................................................... 11
5.2 Panel Button Locking/Unlocking ....................................................................... 12
5.3 Status Information Inquiry ................................................................................ 12
5.4 EDID Management ........................................................................................... 13
5.5 Audio Setting .................................................................................................... 15
5.6 Preset Setting ................................................................................................... 17
5.7 IP Address Inquiry ............................................................................................ 18
6. GUI Control ................................................................................................................ 19
6.1 Signal Switching ............................................................................................... 20
6.2 Audio Setting .................................................................................................... 21
6.3 Configuration .................................................................................................... 23
6.3.1 Down-scaling .......................................................................................... 23
6.3.2 HDCP Setting ......................................................................................... 24
6.3.3 EDID Copy ............................................................................................. 25
6.3.4 EDID Setting .......................................................................................... 26

8x8 HDMI 2.0 HDBaseT Matrix Switcher
6.4 CEC Control ..................................................................................................... 27
6.5 RS232 Control .................................................................................................. 30
6.6 Access Setting .................................................................................................. 31
6.7 Interface Setting ............................................................................................... 32
6.8 Network Setting ................................................................................................ 33
6.9 GUI Upgrade .................................................................................................... 34
7. IR Control .................................................................................................................. 35
7.1 IR Remote Control ............................................................................................ 35
7.2 IR Pass-through Control ................................................................................... 35
7.2.1 Control Local Input Device from Remote ............................................... 36
7.2.2 Control Remote Output Device from Local ............................................ 38
8. RS232 Control ........................................................................................................... 40
8.1 RS232 Control Connection ............................................................................... 40
8.1.1 Control the Matrix Switcher from Local .................................................. 40
8.1.2 Control the Matrix Switcher from Remote .............................................. 41
8.1.3 Control the Remote Third-party Device from Local ................................ 42
8.1.4 Control the Local Third-party Device from Remote ................................ 43
8.2 RS232 Control Software ................................................................................... 44
8.3 RS232 Commands ........................................................................................... 45
8.3.1 System Setting ....................................................................................... 45
8.3.2 Signal Switching ..................................................................................... 48
8.3.3 Audio Setting .......................................................................................... 50
8.3.4 HDCP Setting ......................................................................................... 54
8.3.5 EDID Management ................................................................................. 55
8.3.6 Third-party Device Control ..................................................................... 56
8.3.7 CEC Control ........................................................................................... 57
9. Firmware Upgrade ..................................................................................................... 60
10. Panel Drawing ......................................................................................................... 61
11. Troubleshooting & Maintenance .............................................................................. 62
12. Customer Service .................................................................................................... 63

8x8 HDMI 2.0 HDBaseT Matrix Switcher
1
1. Product Introduction
Thanks for choosing the professional 8x8 HDMI 2.0 HDBaseT matrix switcher with
eight receivers! The matrix is an eight-input by eight-output HDBaseT and HDMI matrix
with HDCP 2.2 and up to 4K/UHD@60Hz video support. It transmits 4K video to
distances up to 131 feet (40 meters) and 1080p video to distances up to 230 feet (70
meters) over a single CATx Ethernet cable. The eight HDBaseT outputs support 24V
Power over Cable (PoC) feature, allowing the receivers to draw their power from the
matrix over the HDBaseT cable.
The matrix switcher features comprehensive EDID management and advanced HDCP
handing to ensure maximum functionality with a wide range of video sources.
The matrix switcher not only supports bi-directional IR, RS232 extension but also has
IR, RS232, and TCP/IP control options.
The product provides performance in control and transmission, which could be used in
a number of different installation scenarios, for example, with computers, for monitoring
purposes, large screen displays, conference systems, television education, bank
security institutions, etc.
1.1 Features
l 8x8 HDBaseT matrix switcher with audio matrix.
l Fully compliant with the HDMI 2.0 and HDCP 2.2.
l Supports HDMI resolution up to 4K@60Hz 4:4:4, HDR10.
l Features eight mirrored HDMI outputs for eight HDBaseT outputs, and the eight
HDMI outputs support 4K to 1080p down-scaling.
l The eight HDBaseT outputs support 24V PoC, allowing the receivers to draw their
power from the matrix switcher over the HDBaseT cable.
l Transmits 4K signal to the distance up to 131 feet (40 meters) and 1080p signal to
the distance up to 230 feet (70 meters) over a single CATx Ethernet cable.
l Supports audio matrix. Provides eight digital SPDIF audio outputs and eight analog
L+R audio outputs for HDMI input audio de-embedding and HDBaseT output audio
de-embedding. Moreover, the eight digital SPDIF audio outputs supports ARC audio
output from receivers.
l Volume adjustment for analog L+R audio outputs.
l Supports comprehensive EDID management and advanced HDCP handling.
l Controllable via front panel buttons, RS232 local and pass-through, IR local and
pass-through, CEC, and TCP/IP (built-in GUI).

8x8 HDMI 2.0 HDBaseT Matrix Switcher
2
1.2 Package List
HDBaseT Matrix
Switcher
l 1x MUH88T-H2 8x8 HDMI 2.0 HDBaseT Matrix Switcher
l 2x Mounting Ears with 6 Screws
l 4x Plastic Cushions with 4 Screws
l 1x IR Receiver
l 1x IR Remote
l 1x RS232 Cable (3-pin to DB9)
l 16x 3-pin Terminal Blocks
l 1x Power Cord
HDBaseT Receiver
l 8x TPUH610SR HDBaseT Receivers
l 16x Mounting Ears with 32 Screws
l 32x Plastic Cushions
l 8x 3-pin Terminal Blocks
l 1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

8x8 HDMI 2.0 HDBaseT Matrix Switcher
3
2. Specification
2.1 Matrix Switcher
Video Input
Input
(8) HDMI
Input Connector
(8) Type-A female HDMI
HDMI Input Resolution
Up to 4Kx2K@60Hz 4:4:4, HDR10,1080p 3D
Video Output
Output
(8) HDBaseT, (8) HDMI
Output Connector
(8) RJ45, (8) Type-A female HDMI
HDMI Output Resolution
Up to 4Kx2K@60Hz 4:4:4, HDR10, 1080p 3D.
Supports 4K to 1080p down-scaling.
HDBaseT Output Resolution
Up to 4Kx2K@60Hz 4:2:0
HDMI Audio Signal
LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, Dolby Digital®
Plus, DTS:X™, and DTS-HD® Master Audio™ pass-through.
Audio Output
Output
(8) Stereo analog L+R audio, (8) Digital SPDIF audio
Output Connector
(8) 3-pin terminal blocks, (8) Tosli n k co n n ect o r s
Analog L+R Audio Format
Supports PCM
Digital SPDIF Audio Format
Supports PCM, Dolby Digital, DTS, DTS-HD
Local Audio Sampling Rate
Supports 44.1KHz, 48KHz, 96KHz
ARC Audio Sampling Rate
Supports 48KHz, 96KHz
Frequency Response
20Hz – 20KHz, ±3dB
Audio Output Impedance
70Ohms
Max Input Level
L+R: 2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV
(316mV) nominal consumer line level signal.
SPDIF:±0.05dBFS.
THD+N
< 0.05% (-80dB), 20Hz – 20KHz bandwidth, 1KHz sine at 0dBFS
level (or max level).
SNR
L+R: > 80dB, 20Hz - 20KHz bandwidth.
SPDIF: > 90dB, 20Hz-20 kHz bandwidth.
Crosstalk Isolation
SPDIF: < -70 dB, 10KHz sine at 0dBFS level (or max level before
clipping).
L+R: < -80 dB, 10KHz sine at 0dBFS level (or max level before
clipping).
L-R Level Deviation
L+R: < 0.3dB, 1KHz sine at 0dBFS level (or max level before
clipping).
Frequency Response
Deviation
< ± 0.5dB 20Hz - 20KHz.

8x8 HDMI 2.0 HDBaseT Matrix Switcher
4
Output Load Capability
L+R: 1KΩ and higher (Supports 10x paralleled 10KΩ loads).
Stereo Channel Separation
>70dB@1KHz.
Noise Level
L+R: -80dB; SPDIF: -90dB
Control Part
Control port
(8) IR IN, (1) IR ALL IN, (8) IR OUT, (1) IR ALL OUT, (1) IR EYE,
(9) RS232, (1) FIRWARE, (1) TCP/IP
Control Connector
(19) 3.5mm jacks, (9) 3-pin terminal blocks, (1) Type-A USB, (1)
RJ45
General
Transmission Mode
HDBaseT
Transmission Distance
1080p ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)
Bandwidth
18Gbps
Operation Temperature
-5℃ ~ +55℃
Storage Temperature
-25℃ ~ +70℃
Relative Humidity
10% ~ 90%
External Power Supply
100V~240V AC, 50/60Hz
Power Consumption
125W (Max)
Dimension (W*H*D)
436.6mm x 88mm x 440mm
Net Weight
5.8kg
2.2 HDBaseT Receiver
Video
Input
(1) HDBT
Input Connector
(1) RJ45
Input Resolution
Up to 4Kx2K@60Hz 4:2:0
Output
(1) HDMI
Output Connector
(1) Type-A female HDMI
Output Resolution
Up to 4Kx2K@60Hz 4:4:4 8bit, HDR10
Audio
Input
(1) ARC Audio In
Input Connector
(1) Toslink Connector
Output
(1) Audio Breakout
Output Connector
(1) Toslink connector
Audio Format
Supports PCM, Dolby Digital, Dolby True-HD, DTS and DTS-HD.

8x8 HDMI 2.0 HDBaseT Matrix Switcher
5
Frequency Response
20Hz – 20KHz, ±3dB
Max Output Level
2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV)
nominal consumer line level signal
THD+N
< 0.05% (-80dB), 20Hz – 20KHz bandwidth, 1KHz sine at 0dBFS
level (or max level)
SNR
> 85dB, 20Hz-20 kHz bandwidth
Crosstalk Isolation
> 70dB, 10KHz sine at 0dBFS level (or max level before clipping)
L-R Level Deviation
< 0.3dB, 1KHz sine at 0dBFS level (or max level before clipping)
Frequency Response
Deviation
< ± 0.5dB 20Hz - 20KHz
Output Load Capability
1KΩ and higher (Supports 10x paralleled 10KΩ loads)
Stereo Channel Separation
>70dB@1KHz
Control
Control Part
(1) ARC Mode button, (1) FW, (1) IR In, (1) IR Out, (1) RS232
Control Connector
(1) Micro-USB port, (2) 3.5mm jacks, (1) 3-pin terminal block
General
Bandwidth
18Gbps
HDMI Standard
2.0
HDCP Version
2.2, 1.4 compliant
CEC
Pass-through
Bidirectional PoC
Supported
HDMI 2.0 Cable Length
4K@60Hz 4:4:4 ≤ 5m, 4K@60Hz 4:2:0 ≤ 15m, 1080p ≤ 20m
Transmission Standard
HDBaseT
Transmission Distance
1080p@60Hz ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)
Operation Temperature
-5℃ ~ +55℃
Storage Temperature
-25℃ ~ +70℃
Relative Humidity
10%-90%
Power Supply
Input:100V~240V AC; Output:24V DC 1.25A
Power Consumption
12W (Max)
Dimension (W*H*D)
40mm x 19.5mm x 84mm
Net Weight
290g

8x8 HDMI 2.0 HDBaseT Matrix Switcher
6
3. Panel Description
3.1 Matrix Switcher Front Panel
①
LCD Screen: Presents real-time operation status.
②
Power LED: Illuminates RED when the device is in standby mode, illuminates
GREEN when device is powered on.
③
IR Sensor and its LED: Illuminates RED when the IR sensor receives an IR signal
from the IR remote to control the matrix switcher. The IR sensor is on the right side
of the LED.
④
INPUT: Eight buttons for input source selection.
⑤
OUTPUT: Eight buttons for output channel selection.
⑥
Menu Buttons:
l LOCK: Lock or unlock the front panel buttons.
l PRESET: Preset setting.
l MENU/↲: Menu or confirm button.
l BACK: Go back to the previous operation.
l UP: Page up.
l DOWN: Page down.
PWR
IR
1 2 3456 7 8
INPUT
UPMENU/
1 2 3456 7 8 DOWN
BACKPRESET
1 3
24 6
5

8x8 HDMI 2.0 HDBaseT Matrix Switcher
7
3.2 Matrix Switcher Rear Panel
①
INPUT: Eight type-A female HDMI input ports to connect HDMI sources.
②
AUDIO MATRIX OUT/ARC: Eight 3-pin terminal blocks and eight Toslink
connectors to connect speakers or amplifiers for HDMI input audio de-embedding
or HDBaseT output audio de-embedding, and the eight Tosl ink conn ect ors can
also be used for ARC audio output from HDBaseT receivers. They can make up an
audio matrix to be set by front panel buttons, GUI or RS232 commands.
③
OUTPUT: Eight HDBaseT RJ45 outputs to connect the eight HDBaseT receivers,
and eight local HDMI ports to connect local displays.
④
CONTROL:
l RS232: 3-pin terminal block to connect the control device (e.g. PC) to control
the matrix switcher by RS232 commands.
l IR EYE: 3.5mm jack to connect IR receiver to control the matrix switcher by the
IR remote.
l FW: Type-A USB port for firmware upgrade.
l TCP/IP: RJ45 port to connect the control device (e.g. PC) to control the matrix
switcher by GUI.
⑤
RS232: Eight 3-pin terminal blocks to control the third-party devices base on
RS232 pass-through feature. There is a one-to-one correspondence between the
eight RS232 ports and the eight RS232 ports of eight HDBaseT receivers.
⑥
IR IN:
l 1~8: Eight 3.5mm jacks to connect eight IR receivers. Each IR input is
associated with the respective HDBaseT output and cannot be switched
separately. It makes up a bi-directional IR transmission with the IR OUT on the
corresponding HDBaseT receiver.
l ALL IN: 3.5mm jack to connect the IR receiver to transmit the IR signal from the
RS232
Tx Rx
FWIR EYE TCP/IP 1 2 3 4 56 7 8 AL L IN 1 2 3 4 56 7 8 AL L OUT
Tx Rx
1 2 3 4 56 7 8 1 2 3 4 56 7 8
L R
1 2 3 4 56 7 8
HDB as eT H DM I
1 2 3 4 56 7 8 1 2 3 4 56 7 8
1239
4578
6

8x8 HDMI 2.0 HDBaseT Matrix Switcher
8
ALL IN port to all HDBaseT receivers.
⑦
IR OUT:
l 1~8: Eight 3.5mm jacks to connect eight IR emitters to send the IR signal
received from the corresponding HDBaseT receivers.
l ALL OUT: 3.5mm jack to connect the IR emitter to send the IR signal received
from all HDBaseT receivers.
⑧
AC100V~240V: Power port to connect an AC 100V~240V power by the power
cord.
⑨
GROUND: Connect to earth to ensure the unit is well grounded.
3.3 Receiver Front and Rear Panel
①
Power LED: The LED illuminates red when power is applied.
②
ARC Mode: Press the button with paper clip or other sharp tool to enable the ARC
mode, and then the left LED illuminates blue. Press it again to exit the ARC mode
and the LED is off. When the ARC audio is selected as the audio source for the
SPDIF output of matrix switcher, the ARC mode will be enabled automatically.
③
ARC Audio In: Tos link conn ec tor to co nne ct AR C audi o so urc e de vice (e. g.TV ).
④
FW: Micro-USB port for firmware upgrade.
⑤
HDMI Out: Type-A female HDMI output port to connect HDMI display (e.g.TV).
⑥
Audio Breakout: If the ARC mode is OFF, the Toslink connector is connected to
speaker or amplifier for HDMI source audio de-embedding. Note that if the ARC
mode is ON, this port has no audio output.
⑦
IR In: 3.5mm jack to connect the IR receiver for IR pass-through.
⑧
IR Out: 3.5mm jack to connect the IR emitter for IR pass-through.
⑨
RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a
third-party device to be controlled.
12345678911
10

8x8 HDMI 2.0 HDBaseT Matrix Switcher
9
⑩
HDBT In: RJ45 port to connect the HDBT output port of switcher/transmitter by
CATx Ethernet cable. The LINK LED illuminates orange when there is a valid
HDBaseT link between the switcher/transmitter and the receiver. The HDCP LED
illuminates green when the video contains HDCP content.
⑪
DC 24V: DC connector for the power adapter connection. If the
switcher/transmitter is connected to the power adaptor, the receiver doesn’t need
to connect power adaptor due to the HDBT output port of switcher/transmitter
supports 24V PoC output.

8x8 HDMI 2.0 HDBaseT Matrix Switcher
10
4. System Connection
4.1 Usage Precaution
l Make sure all components and accessories included before installation.
l System should be installed in a clean environment with proper temperature and
humidity.
l All of the power switches, plugs, sockets, and power cords should be insulated and
safe.
l All devices should be connected before power on.
4.2 System Diagram
The following diagram illustrates typical input and output connections that can be
utilized with this matrix switcher:
Tx Rx
LINKHDCP
Receiver
Projector
Blu-ray Remote
IR Emitter IR Receiver
Tx Rx
LINKHDCP
Receiver
Projector
Blu-ray Remote
IR Emitter IR Receiver
RS232
Tx Rx
FWIR EYE TCP/IP 1 2 3 4 5 6 7 8 ALL IN 1 2 3 4 5 6 7 8 ALL OUT
Tx Rx
12345678 12345678
L R
12 3 4 5 6 7 8
HDBa seT HD MI
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
HDMI:
IR:
RS232:
HDBaseT:
Ethernet:
Audio:
Apply TV 4K Blu -Ray
Laptop
Matr ix Re mote IR Receiver
HDTV HDTV
Amplifier Speaker
Speaker Speaker Speaker Speaker
Router
Proj ector
Remote
IR Receiver
IR Emi tter

8x8 HDMI 2.0 HDBaseT Matrix Switcher
11
5. Button Control
The matrix switcher can be controlled by using the buttons on the front panel.
Whenever a command is accepted, the indicators of all the buttons pressed will blink
three times then they will go off. If the command fails, the indicators will go off
immediately without blinking.
5.1 Signal Switching
l Switch an input to an output
Operation: INPUT# + OUTPUT# + MENU/↲"
Example: Switch Input 1 to Output 2:
Press INPUT 1 Press OUTPUT 2
Press to confirm.
Note: In default status, 8 IR OUT ports correspond with 8HDMI INPUTS. When you
switch an HDMI input, the corresponding IR OUT will be switched synchronously.
l Switch an input to several outputs
Operation: INPUT# + OUTPUT# + OUTPUT# +… + MENU/↲
Example: Switch Input 1 to Output 2, 3, and 4.
Press INPUT 1 Press OUTPUT 2, 3, 4
Press to confirm.
SWITCH:1 ->
SWITCH:1 ->
2
SWITCH:1 ->
SWITCH:1 ->
2 3 4

8x8 HDMI 2.0 HDBaseT Matrix Switcher
12
5.2 Panel Button Locking/Unlocking
Press and hold at least three seconds. Press
and hold to unlock.
5.3 Status Information Inquiry
Press Press enter status
information tab. Press or navigation buttons to check the previous
or next item respectively.
LCD Screen
Description
Report the signal switching status.
Report the connection status of all HDMI input ports.
Y means the corresponding input port is connected to
a source device, N means there is no connection
between the input port and source device.
1~8=HDBaseT output 1~8.
Report the connection status of all HDBT output
ports.
Y means the corresponding output port is connected
to an HDBaseT receiver, N means there is no
connection between the output port and HDBaseT
receiver.
HDBT Matrix
System Locked
HDBT Matrix
System Unlocked
Status Info <
EDID Management
IN 1 1 1 1
1 2 3 4
OUT
IN 1 1 1 1
5 6 7 8
OUT
IN 1 2 3 4
Y Y Y Y
LINK
IN 5 6 7 8
Y N N N
LINK
OUT 1 2 3 4
Y Y Y Y
LINK
OUT 5 6 7 8
Y N N N
LINK

8x8 HDMI 2.0 HDBaseT Matrix Switcher
13
9~16=HDMI loop output
1~8.
Report the connection status of all HDMI loop output
ports.
Y means the corresponding output port is connected
to a display device, N means there is no connection
between the output port and display device.
5.4 EDID Management
The Extended Display Identification Data (EDID) is used by the source device to match
its video resolution with the connected display. By default, the eight source devices
invoke the fifth built-in EDID: 4K@60Hz HDR 2CH.
l Enter EDID management tab:
Press Press to select EDID Management
Press enter EDID management tab. Press
or navigation buttons to select the below items:
ü Learn HDBT OUT
ü Learn HDMI OUT
ü Built-in EDID
l To copy the EDID data from one HDBT output to one or several inputs:
Example: Input 1, 2, 3 and 4 learn the EDID data of HDBT output 2.
Select Learn HDBT OUT Press to confirm.
Press OUTPUT 2
OUT 9 10 11 12
Y Y Y Y
LINK
OUT 13 14 15 16
Y Y Y Y
LINK
Status Info
EDID Management <
Learn HDBT OUT <
Learn HDMI OUT
PRESS INPUT KEY
Learn HDBT OUT 1
PRESS INPUT KEY
Learn HDBT OUT 2

8x8 HDMI 2.0 HDBaseT Matrix Switcher
14
Press INPUT 1, 2, 3, 4.
Press to confirm.
l To copy the EDID data from one HDMI output to one or several inputs:
Example: Input 1 and 2 learn the EDID data of HDMI output 4.
Select Learn HDMI OUT Press to confirm.
Press OUTPUT 4
Press INPUT 1 and 2. Press
to confirm.
l To invoke the built-in EDID data:
There are six types of built-in EDID data can be invoked, as shown as below:
No.
EDID
Video
Audio
1
1080p
2CH
2
1080p HDR
MultiCH
3
4K@30Hz HDR
2CH
4
4K@60Hz HDR
MultiCH
5 (Default)
4K@60Hz HDR
2CH
6
4K@60Hz HDR
MultiCH
User Custom
Example: Input 1 and 2 invoke the built-in EDID data: 4K@30Hz HDR 2CH.
Select Built-in EDID Press to confirm.
Press or navigation buttons to select the
1 2 3 4
Learn HDBT OUT 2
Learn HDBT OUT
Learn HDMI OUT <
PRESS INPUT KEY
Learn HDMI OUT 1
PRESS INPUT KEY
Learn HDMI OUT 4
1 2
Learn HDMI OUT 4
Learn HDMI OUT
Built-in EDID <
PRESS INPUT KEY
1080P 2CH <

8x8 HDMI 2.0 HDBaseT Matrix Switcher
15
built-in EDID to be invoked Press INPUT 1 and 2.
Press to confirm.
5.5 Audio Setting
The matrix switcher provides eight analog L+R audio output ports and eight digital
SPDIF output ports for audio de-embedding. The audio source selection of these eight
audio output ports, and the L+R audio volume can be controlled by the front panel
buttons.
l Audio Source Selection
There are sixteen audio sources can be selected for any analog L+R audio output port,
and twenty-four audio sources can be selected for any SPDIF audio output port.
Audio Output Ports
Audio Sources
Input Breakout
Output Breakout
ARC
L+R OUT 1
In1 Breakout
In2 Breakout
In3 Breakout
In4 Breakout
In5 Breakout
In6 Breakout
In7 Breakout
In8 Breakout
Out1 Breakout
Out2 Breakout
Out3 Breakout
Out4 Breakout
Out5 Breakout
Out6 Breakout
Out7 Breakout
Out8 Breakout
/
L+R OUT 2
L+R OUT 3
L+R OUT 4
L+R OUT 5
L+R OUT 6
L+R OUT 7
L+R OUT 8
SPDIF OUT 1
In1 Breakout
In2 Breakout
In3 Breakout
In4 Breakout
In5 Breakout
In6 Breakout
In7 Breakout
In8 Breakout
Out1 Breakout
Out2 Breakout
Out3 Breakout
Out4 Breakout
Out5 Breakout
Out6 Breakout
Out7 Breakout
Out8 Breakout
Out1 ARC
Out2 ARC
Out3 ARC
Out4 ARC
Out5 ARC
Out6 ARC
Out7 ARC
Out8 ARC
SPDIF OUT 2
SPDIF OUT 3
SPDIF OUT 4
SPDIF OUT 5
SPDIF OUT 6
SPDIF OUT 7
SPDIF OUT 8
PRESS INPUT KEY
4K30HDR 2CH <
1 2
4K30HDR 2CH <