Wyrestorm RX-70-IR-POH User manual

1
Technical Support: [e-mail] US: [phone] EU: [phone]
Instruction Manual
Thank you for choosing this WyreStorm product.
Please read these instructions carefully before installing to avoid complications later.
WyreStorm Extender Set
Solutions
RX-70-IR-POH
HDMI®Extension over Cat5e/6/7 with Class B
HDBaseTTM up to 70m/230ft with bidirectional
IR control, routed RS232 and Power-over-
HDBaseT

2
Technical Support: [email protected] US: [phone] EU: [phone]
Contents 1. Introduction
CONTENTS AND INTRODUCTION
As part of the WyreStorm Pro Plus range of matrices
and extenders, the RX-70-IR-POH display receiver
has been developed for more aordable HDBaseT
installations that demand the benets of an
HDBaseT transmission, including distribution of full
HD video, audio and bidirectional IR control over a
single Cat5e/6 cable up to 70m/230ft.
As an evolution of the Pro Plus range, the RX-70-IR-POH
also features support of routed serial control and Power-
over-HDBaseT for full compatibility with MX-PP-POH xed
and customisable matrices to offer system integrators
even greater exibility and application opportunities,
combined with out-of-the-box convenience that add
signicant value to any installation.
More Power
PoH enables low voltage power to be passed along
the Cat5e/6 cable from an MX-PP-POH matrix to
power RX-70-IR-POH receivers without the need
for local mains power at display zones for greater
exibility and convenience during installation as well as
improved energy efciency compared to a permanent
mains connection.
More Control
RX-70-IR-POH also supports routable serial control via
RS232 to allow central control of all connected display
devices, with protocols for leading control systems
available on the website product page – all of which adds
up to an incredibly powerful package for residential and
commercial applications of any size or budget.
Using the very latest Class B HDBaseT platform, the
RX-70-IR-POH supports single cable 36bit Deep Color
1080p HD Video @60Hz, including full frame-packing 3D
(Blu-Ray), HD multichannel audio and discrete IR control
of source and display from either location and routable
RS232 control using unshielded or shielded Cat5e/6
cable.
The RX-70-IR-POH has been designed for integration with
MX-PP-POH matrices and other WyreStorm HDBaseT
solutions, such as the AMP-001-010 Digital Audio
Amplier for distribution of full, uncompressed HD video,
audio and control combined with 2:1 audio, speaker/sub
connections, ARC and local audio input to create a total
HD AV distribution system including EDID management
and HDCP compliance.
Never has so much been possible for so little.
Introduction
Features
Safety Precautions
Package Contents
Connection & Operation
i. Pro Plus PoH Cabling Guide / Typical Application
ii. RJ45 Termination & Distance
iii. Initial Connection
iv. IR/RS232 Control Connection
RS232 - Understanding RS232 Connection and Signals
Updating RS232 Settings
Maintenance
Product Service
Panel Descriptions
1
2
3
4
5
6
7
8
9
10
11
12
14
15 Mail In Service
Warranty
i. Warranty Limits and Exclusions
Installation Notes
Specication
Troubleshooting
FAQ’s
RS232 Connection
16
17
13

3
Technical Support: [email protected] US: [phone] EU: [phone]
2. Features
FEATURES AND SAFETY PRECAUTIONS
• Receivers capable of 1080p HD video @60Hz and
HD multichannel audio transmissions up to
70m/230ft under perfect conditions*
• Transmits discrete wide-band two-way IR control
signal together within the HDMI signal over a single
Cat5e/6/7
• Robust Class B HDBaseT transmission technology
for more affordable HD distribution and control
whilst retaining the trademark HDBaseT stability
and resistance to electrostatic and environmental
interference compared to conventional UTP
transmission
• Power-over-HDBaseT for receivers to draw power
directly from the transmission device. No mains
power supply required at display location
• Supports all high denition resolutions: 1080p,
1080i, 720p with screen refresh rates of 24Hz,
30Hz, 50Hz and 60Hz
• Centralized Routed RS232 for serial control of
display devices, including third party control with
open source integration protocols available for
market leading control systems
• Output zone (7 x 70m/230ft) using another Class
B HDBaseT transmission device
• Fully supports 3D applications (frame-packing/
sequential – Blu-ray and Interlaced Stereoscopic
– Satellite/cable broadcasts)
• Supports 36bit Deep Colour
• HDMI V1.4
• Cable termination follows IEEE-568B standards
• HDCP compliant
• Automatically adjusts feedback, equalization
and amplication of signal for easy installation
• LED indication for visual link status and video
signal status
• Mounting bracket included
*Perfect transmission conditions - cable run within
specied distance range of product, no electrical
interference, the use of straight cable runs with no bends
or kinks and no patch panels or wall outlets used. Please
be advised that the presence of any of these factors in
your installation may compromise bandwidth and signal
strength.
Part Number RX-70-IR-POH
Innovation for Inspired Integration
For further information on this product and other
WyreStorm ranges, visit our website or download our
latest product guide. www.wyrestorm.com
For longer transmission distance, Ethernet pass- through,
to enable devices with 4k resolution or for 48bit Deep
Colour compatibility, please see our range of full HDBaseT
receivers and extender sets.
3. Safety Precautions
1. Do not expose this apparatus to rain, moisture,
sprays, drips or splashes and ensure that no
objects containing liquids are placed on the
apparatus, including cups, glasses and vases.
2. Do not place this unit in a conned space such as
enclosed shelving, cabinets or bookshelves.
Ensure the unit is adequately ventilated.
3. To prevent the risk of electric shock or re hazard
due to overheating, do not cover the unit or
obstruct ventilation openings with material,
newspaper, cardboard or anything that may restrict
airow into the unit.
4. Do not install near external heat sources such as
radiators, heat registers, boilers or any device that
produces heat such as ampliers or computers and
do not place near sources of naked ame.
5. Unplug apparatus from power supply during
lightening storms or when unused for long periods
of time.
6. Protect the power cable from being walked on,
pinched or restricted in any way, especially at plug
connections.
7. Only use attachments/accessories specied by the
manufacturer.
8. Units contain non-servicable parts - Refer all
servicing to qualied service personnel.
WARNING
To reduce the risk of re, electric shock
or product damage:
4
Technical Support: [email protected] US: [phone] EU: [phone]
FEATURES AND SAFETY PRECAUTIONS
MX0404-QI
• Quick and easy installation – set up in seconds straight out of
the box.
• Simplied ports - Input: HDMI – Output: integrated RJ45
connectors for a single Cat5e/6/7 UTP cable to each display
point for ease of installation.
• Conforms to IEEE-568B standards
• Each HDMI port also supports DVI signals.
• Each Output port can be fed to multiple displays (cascaded).
• Enables up to 4 HDMI video/audio devices to be independently
switched through up to 4 HDMI displays or projectors for
uncompressed digital distribution.
• Each output able to show any connected source simultaneously
regardless of whether the input carries HDCP encryption.
• Rened for Custom Install and Home Theatre Installations.
• Reads and copies EDID from connected devices with additional
EDID configuration through customisable DIP switch settings if
necessary.
• 2k resolution supported.
• Fully 3D compatible – Frame sequential 3D (Blu-ray) and
interlaced stereoscopic 3D (satellite broadcasts etc.)
• Supports all high denition resolutions up to and including
1080p and standard video formats.
• RS232 port.
• Choose from 6 switching modes – infrared remote control, front
panel buttons, local IR, IR call-back, LAN and RS232.
• Simple switching remote control included, which can also be
learned into a universal remote handset to allow the control of
multiple devices from one handset.
• Fully compatible for integration with market leading control systems.
• 4 x IR 3.5mm mini-jack ports for each output to link IR from
control system to control display
• Additional infrared extension port for longer IR connections
• HDMI v.1.3
• Supports 24Bit Colour depth
• Signalling rate of 6.75 Gbps
• Pack comes complete with 1 x 4x4 Matrix with 19” rack
brackets, 4 x 40m IR receivers with mounting brackets, IR
receivers, emitters and a Matrix remote control handset.
Additional features included on the RX-1UTP-IR-40
• Transmits one-way signal together with the HDMI signal over a
single Cat5e/6/7 cable.
• Receivers capable of 1080p transmissions up to 40m (131ft)
under ideal conditions*
• For even greater control and ne tuning, each receiver features
a fully adjustable EQ distance range for optimising the
transmission signal.
2. Features
3. Safety Precautions
1. Do not expose this apparatus to rain, moisture, sprays,
drips or splashes and ensure that no objects containing
liquids are placed on the apparatus, including cups,
glasses and vases.
2. Do not place this unit in a confined space such as
enclosed shelving, cabinets or bookshelves. Ensure the
unit is adequately ventilated.
3. To prevent the risk of electric shock or fire hazard due to
overheating, do not cover the unit or obstruct ventilation
openings with material, newspaper, cardboard or
anything that may restrict airflow into the unit.
4. Do not install near external heat sources such as
radiators, heat registers, boilers or any device that
produces heat such as amplifiers or computers and do
not place near sources of naked flame.
5. Unplug apparatus from power supply during lightening
storms or when unused for long periods of time.
6. Protect the power cable from being walked on, pinched
or restricted in any way, especially at plug connections.
7. Only use attachments/accessories specified by the
manufacturer.
8. Units contain non-servicable parts - Refer all servicing to
qualified service personnel.
WARNING
To reduce the risk of fire, electric shock
or product damage:
• Protection against ESD (electrostatic discharge) included within
the unit to further stabilise transmission.
• LED indications for clear power and video signal selection.
• 5v mains supply included but receivers may be powered through the
USB port of the display using Wyrestorm USB to 5v power adaptor)
• Fully cascadable to further lengthen transmission.
*NOTE: ideal conditions denote cable run is within
specified distance range of product, no electrical
interference, the use of straight cable runs with no bends
or kinks and no patch panels or wall outlets used. Please
be advised that the presence of any of these factors in
your installation may compromise bandwidth and signal
strength. For longer transmission distances, RS232 control
and Ethernet pass-through, please see our full HDBaseT
or HDBT Lite range of matrices, transmitters, receivers and
extender sets.
USB to 5V Cable
Part Number CAB-USB-5V

4
Technical Support: [email protected] US: [phone] EU: [phone]
4. Package Contents
1 x WyreStorm RX-70-IR-POH Display Receiver
1 x Printed installation guide (digital version also
downloadable from www.wyrestorm.com product
page)
1 x Receiver mounting brackets
1 x 5VDC power supply (for optional power supply)
1 x Wide-band IR RX Receiver (larger/rectangular) for
attachment to Display - IR frequency range: 940nm IR
Frequency: 38KHZ
SAFETY PRECAUTIONS, PACKAGE CONTENTS AND SPECIFICATIONS
5. Specications
Operating Temperature Range -5 to +35ºC (-41 to -95ºC)
Operating Humidity Range 5 to 90% RH (no condendation)
Output Bandwith Signalling Rate 6.75Gbps
Input Video Signal 0.5 - 1.0 volts p-p
Input DDC Signal 5 volts p-p (TTL)
Maximum Signal Link Range 1080p 36bit Deep Colour
Transmission distance 1080p signal up to 70m/230ft
Video Format Supported VESA: 640x480, 800x600, 1024x768,
1280x1024, 1600x1200, 1920x1080 1920x1200
DTV/HDTV:
480i/567i/480p/567p/720p/1080i/1080p
Output Video HDMI 1.4+ HDCP (sink mirrors source)
Audio Format Supported DTS-HD Master Audio, Dolby True HD, multi-channel 5.1, 7.1
Max. Transmission distance over HDMI 15m / 49ft (using good quality HDMI cables) - HDMI to
HDMI Coupler can be used to extend HDMI transmission further
if need be.
BTU Rating (British Thermal Unit) 17.3
Power Consumption 5 Watts (Max.)
Power Supply 5V DC from PoH, mains or USB 5V
Dimensions 90mm/3.5” (W)
25mm/0.98” (H)
120mm/4.72” (D)
Weight 0.35kg/0.77lb
Rack space required N/A

5
Technical Support: [email protected] US: [phone] EU: [phone]
6. Panel Description
PANEL DESCRIPTIONS
RS232 UTP IN LINK HDMI OUT IR RXI XIR TX DC/5V
1 2 3 4 5 6 7 8
3
6
1
4
7
2
5
8
RS232 Port
HDBaseT/PoH IN
LED HDBaseT Signal Link Indicator (Lit for Active)
HDMI Output
IR Receiver Port
IR Transmitter Port
DC 5V Power Input
LED Power Indicator (Lit for Active)
receiver
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT

6
Technical Support: [email protected] US: [phone] EU: [phone]
Control system
WyreStorm 70m
Poh transmitter rs232
ir link
cable
hdmi
ir tx
cat5e/6
70m/230ft
transmitter
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT
rs232
hdmi
ir rx
ir tx
receiver
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT
Control system
TYPICAL APPLICATION AND RJ45 TERMINATION & DISTANCE
Control system
hdmi ir tx
WyreStorm 8x8
Pro Plus Matrix
cat5e/6
70m/230ft
rs232
hdmi
ir rx
ir tx
receiver
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT
rs232
ir link
cable
Control system
7i. Pro Plus PoH Cabling Guide / Typical
Application
Control system
WyreStorm 70m
Poh transmitter rs232
ir link
cable
hdmi
ir tx cat5e/6
70m/230ft
transmitter
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT
rs232
hdmi
ir rx
ir tx
Control system
receiver
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT
cat5e/6
70m/230ft

7
Technical Support: [email protected] US: [phone] EU: [phone]
1
2
3
4
5
RJ45 TERMINATION AND CAT5E/6 CABLE DISTANCE, INITIAL CONNECTION AND IR/RS232 CONTROL CONNECTION
7ii. RJ45 Termination and Cat5e/6 Cable Distance
1
2
3
Cat5e Wiring Guide
The quality of termination for every RJ45 is essential.
Poor terminations leads to intermittent performance
and longer install times
4
7iii. Initial Connection
Connect an HDMI input (such as Blu-Ray, Games
Console, Satellite, Cable, media server etc.) to a
HDBaseT transmission device (such as a WyreStorm
TX-1UTP-IR-70-POH transmitter, AMP-001-010 digital
amplifier or MX-PP-POH matrix solution.
Connect a good quality, well terminated Cat5e/6
cable of no more than 70m/230ft in length between the
UTP/HDBaseT output of the transmission device to the
UTP Input of the RX-70-IR-POH
Attention: 70m/230ft is the maximum
recommended transmission distance for this
classification of HDBaseT equipment and denotes
perfect transmission conditions - including straight
cable runs with no electrical interference, bends,
kinks, patch panels or wall outlets. If any of the
above are a factor in your installation, transmission
range may be affected – take care to avoid where
possible.
Connect the HDMI sink (LED/Plasma display or
digital projector) to the HDMI Output of the RX-70-IR-
POH
If daisy-chaining receivers, repeat process for all
RX-70-IR-POH units installed from your transmission
devices.
For two way control of connected sources and
displays from either location, connect IR transmitters to
the IR TX ports of the HDBaseT Transmitter devices and
RX-70-IR-POH.
Insert IR receivers into IR RX ports of the HDBaseT
Receiver devices and matrix.
If using an RS232-based control system, insert
cables into the RS232 ports of devices to enable RS232
control.
Ensure IR TX transmitters are firmly attached over IR
sensors of devices to be controlled.
NOTE: If unsure of positioning, IR sensors can be located
on devices by shining a flashlight onto the facia of the
device - the IR sensor should be identifiable as a small
round sensor behind the panel. Consult your device
manufacturer handbook if difficulties are experienced.
Ensure IR RX receivers are positioned in clear line of
sight to the remote handset used to control them.
Attention: The RX-70-IR-POH is capable of
recieving Power-over-HDBaseT signal distances
up to 70m/230ft when used between PoH-enabled
devices such as a MX-PP-POH matrix or PoH
transmitters.
7iv. IR/RS232 Control
Connection
Pro Plus Class B HDBaseT Display Receiver with PoH
RX-70-IR-POH
1080p No Signal

8
Technical Support: [email protected] US: [phone] EU: [phone]
UNDERSTANDING RS232 CONNECTION & SIGNALS
DB-9 DB-25 Function
1 8 DCD Data Carrier Detect
2 3 RxD Receive Data
3 2 TxD Transmit Data
4 20 DTR Data Terminal Ready
5 7 GND Ground (Signal)
6 6 DSR Data Set Ready
7 4 RTS Request to Send
8 5 CTS Clear to Send
9 22 RI Ring Indicator
DB-9 to DB-25 Conversion
RS232 Connections
A straight-through cable should be used to connect a DTE (e.g. computer) to a DCE (e.g. Amp, Matrix or Modem), with
all signals from one side connected to the corresponding signals on the other side in a one-to-one basis.
A crossover (null-modem) cable can be used to connect two DTE directly, without a modem in between to cross
transmit and receive data signals between the two sides. There are numerous variations on how control signals are
wired:
DTE Pin Assignment (DB-9) DCE Pin Assignment (DB-9)
1 DCD Data Carrier Detect 1 DCD Data Carrier Detect
2 RxD Receive Data 2 TxD Transmit Data
3 TxD Transmit Data 3 RxD Receive Data
4 DTR Data Terminal Ready 4 DSR Data Set Ready
5 GND Ground (Signal) 5 GND Ground (Signal)
6 DSR Data Set Ready 6 DTR Data Terminal Ready
7 RTS Request to Send 7 CTS Clear to Send
8 CTS Clear to Send 8 RTS Request to Send
9 RI Ring Indicator 9 RI Ring Indicator
8. Understanding RS232 Connection & Signals
RS-232C, EIA RS-232, or simply RS-232, refers to
the same standard defined by the Electronic Industries
Association in 1969 for serial communication.
DTE and DCE
DTE stands for Data Terminal Equipment. A computer
or control system is DTE and connects to Data
Communication Equipment, or DCE such as an Amp,
Matrix or Modem.
DTE equipment typically feature a Male Connector, while
DCE contains a Female Connector, although that is not
always true - a simple way to confirm is to measure Pin
3 and Pin 5 of a DB-9 Connector with a Volt Meter. If a
voltage of -3V to -15V is achieved, the device is DTE. If
the voltage is on Pin 2, then the device is DCE.
NOTE: The result for a DB-25 Connector is reversed
(Please refer to DB-9 to DB-25 conversion table)
1 2 3 4 5
6 7 8 9
RS-232 Pin outs (DB-9)
A male DB-9 connector viewed from the front.
Reverse or back view of male connector for
Female Connector.

9
Technical Support: [email protected] US: [phone] EU: [phone]
UPDATING RS232 SETTINGS
RS-232 Logic Waveform (8N1)
The graphic (p.8 bottom left) illustrates a typical RS232 logic waveform (Data format: 1 Start bit, 8 Data bits, No Parity,
1 Stop bit). The data transmission starts with a Start bit, followed by the data bits (LSB sent first and MSB sent last),
and ends with a “Stop” bit.
The voltage of Logic “1” (Mark) is between -3VDC to -15VDC, while the Logic “0” (Space) is between +3VDC to
+15VDC.
RS232 connects the Ground of 2 different devices together, which is the so-called “Unbalanced” connection. An
unbalanced connection is more susceptible to noise, and has a distance limitation of 15m/49ft.
Straight-through (DB-9
(DTE) (DCE)
1 DCD ------- DCD 1
2 RxD ------- TxD 2
3 TxD ------- RxD 3
4 DTR ------- DSR 4
5 GND ------- GND 5
6 DSR ------- DTR 6
7 RTS ------- CTS 7
8 CTS ------- RTS 8
9 RI ------- RI 9
Crossover (Null-Modern) (DB-9
(DTE) (DCE)
1 DCD ------- DCD 1
2 RxD ------- TxD 3
3 TxD ------- RxD 2
4 DTR ------- DSR 6
5 GND ------- GND 5
6 DSR ------- DTR 4
7 RTS ------- CTS 8
8 CTS ------- RTS 7
9 RI RI 9
0 3 61 4 72 5 stopstart
LSB MSB
Mark (1) -12v
space (0) +12v
9. Updating RS232
Settings
Carefully open the case of the EX-70-IR-PP-POH Receiver. On the edge of the circuit board are positioned two
jumper caps to change settings from the ‘Normal’ position for default operation to ‘Update’, which allows
the system to enter Firmware Update Mode.
Gently move the jumper caps to the ‘Update’ position to allow upgrade through the RS232
port.
Connect USB - Serial Cable to PC and run VS010 RX Firmware Update batch file.
Once update has been completed, be sure to return the jumper caps to the ‘Normal’
position for RS232 control signal transmission to be passed.
Note: Connect RS232 cables to the RS232 port of the EX-70-IR-PP-POH Receiver to form
one extension cable.
1
2
3
4
Update
Normal
1
3 4
2
5 6

10
Technical Support: [email protected] US: [phone] EU: [phone]
RS232 CONNECTION AND TROUBLESHOOTING
11. Troubleshooting
Test Monitor
Part Number TTMONITOR
Signal Generator
Part Number TTSignal
Generally, the majority of HD distribution installation
issues are either caused by minor connection
errors, communication problems between devices,
or when the transmission of high signal bandwidth
is attempted using insufficient cable. Should you
encounter any technical difficulties when installing
and configuring the matrix, we are confident
solutions can be found by working through the
following troubleshooting checklist before seeking
alternative technical support.
No Picture or Poor Quality Picture
1) Power – are all HDBaseT transmitters or matrices
powered? All units should have their own power
source connected ie. 12v for 70m/230ft HDBaseT PoH
transmitters – Please use power supplies included.
Note: Display receivers do not need to be independently
powered if part of an HDBaseT PoH extender set or MX-
PP-POH Matrix solution. Non-PoH display receivers can
also be powered via the display USB port by using the
USB to 5v power cable also supplied with this model.
Are all sources definitely powered and firmly connected?
2) If possible, always use test equipment prior to
installation and to troubleshoot any problems.
3) Distance – Is the cable too long for the signal to be
transmitted effectively? The HDBaseT classification used
within the transmitters and receivers allow transmission of
1080p up to 70m/230ft so make sure the cable distance
matches the project requirements and is well within the
maximum transmission distance of the signal.
Note: If approaching the limits of the transmission
capabilities, transmission should be extended by using
another extender set to ensure the signal reaches its
destination effectively.
10. RS232 Connection
To allow serial commands sent from transmitting device to be sent to display device, simply connect a 9 pin straight
through RS232 cable between the RX-70-IR-POH and your display.
Control system
hdmi ir tx
WyreStorm 8x8
Pro Plus Matrix
cat5e/6
70m/230ft
rs232
hdmi
ir rx
ir tx
receiver
RX70-IR-PP-POH
70m/230ft HDMI Extension over HDBaseT
3D compatible, Bidirectional IR, Power-over-HDBaseT
rs232
ir link
cable
Control system

11
Technical Support: [email protected] US: [phone] EU: [phone]
TROUBLESHOOTING
4) Cable Joins – Joins in the cable run or RJ45
connectors can impact on signal strength, resulting in
reduced transmission that may manifest itself in incorrect
picture quality, picture dropping out or a complete lack of
picture
5) Cable Choice and Signal Reduction – Are stranded
patch leads being used as interconnects between patch
panels or wall outlets? CCA (Copper Clad aluminium)
cables being used? These can reduce transmission
rates by up to 40% – we recommend solid core straight
through with minimum connections used wherever
possible.
6) Correct connection – It may seem obvious but
double check all UTP, HDMI, power and IR cables are
connected to the correct ports.
Note: Even a fraction off can be the difference between
aperfect picture and a blank screen. Double check all
connections are firmly made in the correct ports.
7) Cable wired to 568B standard? Is the cable wired
and terminated correctly and are those terminations
connected to the correct ports? Incorrect wiring and
termination will result in unstable operation or a blank
screen.
8) Electrical interference – HDBaseT is less susceptible
to interference compared to regular transmissions but
the location of cables and devices should be considered
- could any form of interference be generated? If so,
attempt to remove the source of electrical interference
or move the cable run to decrease the effects of the
interference.
9) Is a picture achieved when connecting the source
directly to the display? If not then the problem could lie
with the input or output device rather than the means of
distribution i.e. the cable, receiver or matrix itself.
10) HDMI lead condition and quality – HDMI cables
and connectors are delicate and can be damaged much
easier than component or coax cable. Furthermore,
lead quality varies dramatically, particularly in lower price
brackets. Swap HDMI leads and check operation –
damage to or quality of your leads could be the problem.
If in doubt, swap them over. Always take care inserting
and extracting your HDMI from matrix ports so as not to
damage the connectors or ports.
11) Picture speckles/HD ‘noise’ – represents a poorly
established signal that may be caused by poor quality or
excessive HDMI cable lengths. Try swapping the display
adaptors from a location that is functioning properly or
swapping the outputs of the matrix switch used.
If the problem remains on the same screen this may be
caused by a connection problem between matrix and
display – turn off all equipment and swap the signal
carrying cables at both ends to ascertain if the cable or
termination is at fault.
HD Noise (NO image) may be an HDCP Issue between
the source and display but poor cabling can also cause
this due to poor communication.
12) Blu-ray: 3D – is the equipment used 3D enabled/
compatible? Is a 3D disc being played in a 3D enabled
Blu-ray player or through a compatible AV receiver?
16) Colour distortion – a pink or green screen indicates
an incompatibility between colour spacing formats – the
commonly used RGB or YUV used by older displays.
Some sources allow switching between RGB and YUV
which may solve any colour problems. If not, try changing
the HDMI cable between the source and the matrix to rule
out defective cabling.
No Sound or Poor Quality Audio
Audio is transmitted within the video signal – there is no
separate audio track – so generally a problem with sound
will be accompanied by a problem with picture. However,
if technical issues with audio are experienced, the cause
is typically communication between sources, displays
and/or AV receiver settings.
1) Have specific speaker sets or zones been
enabled? Some AV receivers allow individual speaker
selections assigned to specific zones in the set up so
check the speakers used are fully connected to the
amplifier and correctly assigned within the system set up.
It may be an EDID issue in that the source reads the audio
EDID from the display and only requests two channel
audio and EDID copy from the AVR may be required or
use an embedded EDID in the AMP or Matrix.
Note: If problems are experienced when an AV receiver is
used, the cause is usually the settings of the AVR itself.
Refer to the AVR manufacturer’s guidelines on the correct
settings to use for your requirements.
2) Consistency of audio output between devices – Is
there any discrepancy between the audio output of the
source, the audio or zonal settings of the AV receiver and
the speaker configuration used needed for successful

12
Technical Support: [email protected] US: [phone] EU: [phone]
TROUBLESHOOTING AND FAQ’S
12. FAQ’s
audio replication? If outputting 7.1, make sure all devices
connected are also outputting 7.1
Note: Occasionally with some sources, the device settings
allow the specification of audio output through a TV or an
HDMI port. If using an AV receiver, check the HDMI output
option is selected.
3) Do all the local sources work through the AV
receiver?
Check the operation of each source individually.
Bandwidth
1) If using a graphics-based source (such as a PC/Mac/
media server), make sure the source resolution is set to
a maximum of 1080p, 50Hz. Higher resolutions available
for graphics-based systems require higher bandwidth
that may affect transmission of signals as well as
incompatibility with devices.
IR
1) Check emitters at the IR TX transmitter end
and receivers at the IR RX receiver end – are they
connected to the correct ports on the matrix and display
receiver.
2) Is the emitter correctly positioned on the source?
Fix the emitter directly over the infrared sensor of the
source and attach using the adhesive backing.
Note: Locate the infrared source sensor by using a
flashlight to find the sensor within the facia of the source
display. If necessary, secure the emitter over the sensor
with a small amount of contact adhesive.
3) Is the remote handset powered and sending a
signal?
Note: IR is invisible to the naked eye, so use a digital
camera/ phone camera to check the remote signal – point
the camera at the remote control when pressing a button.
The remote transmitter can be seen flashing to indicate a
signal being sent. Replace batteries if flashing is not seen
on the digital camera screen.
4) IR dropout issues can be due to exterior influences
emitting infrared radiation that can interrupt IR signals.
Ensure emitters and receivers are away from the following
causes of IR interference.
• Direct sunlight, Fluorescent lighting (on cold start up)
• Halogen lighting
• Plasma screens
5) UTP Termination Issues – ensure cables and RJ45
terminations are correct and in good condition at
both transmitter and receiver ends to see if control is
established. If so, a possible re-termination of the cable
could remedy the problem.
6) Are WyreStorm emitters and receivers being used?
The use of third party products/magic eyes may not be
compatible. Always use WyreStorm components included
with your purchase or check compatibility of third party
control systems with your WyreStorm dealer.
7) If problems persist, swap out the IR emitters and
receivers to rule out faults with the units themselves. Use
emitters you know are fully operational to test working
condition.
8) Reactivate the IR call-back function on your matrix
and swap IR ports on the matrix to rule out a fault with
thematrix or connection ports.
9) Should IR remain unresponsive, turn off and disconnect
all cables from the matrix and reconnect zones one at a
time to assess if one location in particular is the problem.
If so, run new cables directly to the display – if this fixes
the problem, it is likely that electromagnetic interference /
damage to the cable somewhere along the run is causing
the IR signal to drop out. Investigate and remove EM
interference from the run or replace damaged UTP cable.
Cat5e or 6?
While our equipment is tested and graded to Cat 5e
cable standard; tests have shown that better results
are achieved when using Cat6 cable. The lower AWG
(American Wire Gauge) uses thicker copper cores ensure
better signal transfer/Transmission rates. Newly installed
cabling should always conform to Part P Regulation and
BS 7671 (17th Edition), and should be terminated to 568B
standard.
Can I use a single Cat 5e/Cat 6 cable?
Although conventional transmission is considered to
be two Cat 5e cables, HDBaseT transmission as used
only requires a single cable; all of the twin cable features
are supported with the added benefit of RS232 control
and Ethernet on 100m/328ft HDBaseT products, with
70m/230ft HDBaseT products removing Ethernet
passthrough functionality.

How far can the signal travel?
Under perfect transmission conditions our HDBaseT
receivers will operate at 50m, 70m or 100m (@1080p)
depending on the model used. Perfect conditions means
no electrical interference, straight cable runs with no
bends or kinks and no patch panels or wall outlets. If
some of the above are factors in your installation then
signal strength and bandwidth can be compromised. If
a cable run is reaching the upper limit of the receivers’
capabilities, then the signal can be boosted by way of an
Amp as an in-line repeater up to 7 times (490m) using
HDBaseT technology.
What about 3D?
The RX-70-IR-POH, all of our matrix switches and most
of our extender products will pass-through a 3D Blu-ray
signal (frame packing - Blu-Ray & Stereoscopic - satellite/
cable).
How do I control the sources?
All of our HDMI distribution products support IR pass-
through from point-to-point extender sets to AMP and
HDBaseT matrices. Most of the range now supports
wideband IR meaning it is compatible with any IR device
available on the market. Our PP and HDBaseT matrix
range (Cat 5e/Cat6) has IR pass-through from each of the
outputs and has discrete IR outputs at the switch end,
meaning you can have multiple identical sources yet the
IR would be routed only to the applicable source.
Do I need power at the TV end?
No. Our RX-70-IR-POH HD display adaptors require
no power supply at the TV end. To operate, the PoH
receivers draw the power from an PoH matrix or PoH
Transmitter. NON PoH devices require 5v. It’s important
that these are powered locally and do not receive remote
power from the rack as there can be issues resulting
from voltage drop along the length of cable. For non-PoH
products, our USB to 5v power cables overcome the
problem of having a second mains outlet behind the TV.
These useful leads draw power from the USB port of the
display to power the receiver, this also means that the
receiver is only powered when the display is on making
the system more energy efficient and environmentally
friendly.
Are WyreStorm products compatible with HDMI 1.4?
HDMI 1.4 refers to a list of ‘features’ that a device is
capable of supporting, including Ethernet channel, return
audio channel, 3Detc. Due to the continuously evolving
nature of the technology, HDMI Licensing LLC have now
decided to simplify terminology by testing and referring to
cable in terms of STANDARD or HIGH-SPEED rather than
in generations 1.3, 1.4 etc.
• STANDARD (or “category 1”) HDMI cables perform
at speeds of 75Mhz or up to 6.75Gbps, which is the
equivalent to a 720p/1080i signal – These HDMI cables
are NOT recommended.
• All WyreStorm equipment support HIGH-SPEED
(or “category 2”) HDMI cables that have been tested
to perform at speeds of 340Mhz or up to 10.2Gbps,
which is the highest bandwidth currently utilised over
an HDMI cable and can successfully handle 1080p
signals including those at increased colour depths and/
or increased refresh rates from the Source. High-Speed
cables are also able to accommodate higher resolution
displays, such as WQXGA cinema monitors (resolution of
2560 x 1600).
What about screens with different resolution
capabilities?
When sending a signal point to point a TV will
communicate it’s capabilities to the source, then the
source will output a suitable signal that compatible (i.e.
1080p Stereo audio). If you were to use a matrix switch
with three 1080p screens and one 1080i screen, the
resultant image would be1080i across all screens. The
matrix switches do not scale per output but instead
negotiate with the source a signal that all screens are
capable of supporting.
How does the Matrix cope with HDCP?
HDCP (High Definition Copyright Protection) is a feature
built in to HDMI devices to prevent theft of or illegal
distribution of HD content. Unlike competing products,
WyreStorm matrix switches are legal and comply with
HDCP regulations. They do this by assigning a “key” to
every display connected to the switch. HDCP “keys” are
assigned to a display when connected to a HDMI device
normally. This doesn’t change when connected to a
switch; it just assigns more of them.
I can get 1080i but not 1080p at a TV location
Firstly ensure that both the source is capable of outputting
1080p and that the TV is Full HD 1080p screen. If this is
the case then the AMP, 70 metre receiver or PP Matrix
may require EDID management setting up using the DIP
switches. This useful feature provides a successful “send
and receive” to ensure swift and stable EDID negotiation
between the source and display. See Troubleshooting
section for more tips on problem solving.
I cannot get a signal from my A/V receiver along a
Cat 5e extender set
Check to ensure that the A/V Receiver isn’t adding CEC
(HDMI Control Protocol) to the outgoing signal, this can
sometimes have an effect on the HDMI signal.
13
Technical Support: [email protected] US: [phone] EU: [phone]
FAQ’S

MAINTENANCE, PRODUCT SERVICE, MAIL-IN-SERVICE, WARRANTY AND WARRANTY LIMITS AND EXCLUSIONS
16i. Warranty Limits and
Exclusions
1. Damage requiring service: This unit should be
serviced by a qualified service personnel if:
• The DC power supply or AC adaptor has been
damaged.
• Objects or liquid have gotten into the unit.
• The unit has been exposed to rain.
• The unit does not operate normally or exhibits a marked
change in performance.
• The unit has been dropped or the cabinet damaged.
2. Servicing Personnel: Do not attempt to service
the unit beyond that described in these operating
instructions. Refer all other servicing to authorised
servicing personnel.
3. Replacement Parts: When parts need replacing,
ensure parts approved by the manufacturer are used
– either those specified by the manufacturer or parts
possessing the same characteristics as the original parts.
Be aware – unauthorised substitutes may result in fire,
electric shock, or other hazards and will invalidate your
warranty.
4. Safety Check: After repairs or service, ask the
service personnel to perform safety checks to confirm
the unit is in proper working condition.When shipping the
unit, carefully pack and send it prepaid, with adequate
insurance and preferably in the original packaging. Please
include a document or letter detailing the reason for
return and include a daytime telephone number and/or
email address where you can be contacted.
If repair is required during the limited warranty period,
the purchaser will be required to provide a sales receipt
or other proof of purchase, indicating date and location
of purchase as well as the price paid for the product.
The customer will be charged for the repair of any unit
received unless such information is provided.
Should you feel your product does not function
adequately due to defects in materials or workmanship,
we (referred to as “the warrantor”) will, for the length of
the period indicated below (starting from the original date
of purchase) either:
a) Repair the product with new or refurbished parts.
or
b) Replace it with a new or refurbished product.
Limited warranty period:
All WyreStorm products are covered by a 3 year PARTS
and LABOUR warranty. During this period there will be no
charge for unit repair, replacement of unit components or
replacement of product if necessary.
The decision to repair or replace will be made by the
warrantor. The purchaser must mail-in the product during
the warranty period. This limited warranty only covers the
product purchased as new and is extended to the original
purchaser only. It is non-transferable to subsequent
owners, even during the warranty period.
A purchase receipt or other proof of original purchase
date is required for the limited warranty service.
1. This Limited Warranty ONLY COVERS failures due
to defects in materials or workmanship and DOES
NOT COVER normal wear and tear or cosmetic
damage.
The limited warranty also DOES NOT COVER damage
that occurs in shipment or failures caused by products
not supplied by the warrantor, failures resulting from
accident, misuse, abuse, neglect, mishandling,
misapplication, alteration, incorrect installation, set-up
adjustment, implementation of/to consumer controls,
improper maintenance, power line surge, lightening
damage, modification, service by anyone other than
a manufacturer-approved service centre or factory-
authorised personnel, or damage attributable to acts of
God.
2. There are no express warranties except as listed
under “limited warranty coverage.” The warrantor
15. Mail-in-service
16. Warranty
14. Product Service
14 Technical Support: [email protected] US: [phone] EU: [phone]
Clean this unit with a soft, dry cloth only. Never use
alcohol, paint thinner or other harsh chemicals.
13. Maintenance

INSTALLATION NOTES
16i. Warranty Limits and
Exclusions
17. Installation Notes
is not liable for incidental or consequential damage
resulting from the use of this product or arising out
of any breach of this warranty.
For example: damages for lost time, the cost of having a
person/persons remove or re-install previously installed
equipment, travel to and from service location, loss of or
damage to media, images, data or other recorded/stored
content. The items listed here are not exclusive, but are
for illustration only.
Parts and service not covered by this limited warranty
are not the responsibility of the warrantor and should be
considered the responsibility of the individual.
15
Technical Support: [email protected] US: [phone] EU: [phone]

www.wyrestorm.com
WyreStorm Offices
US Office: 6991 Appling Farms Parkway, Suite 104, Memphis, TN 38133
Tel: + 901 384 3575 Fax: + 901 384 3574
Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK
Tel: [phone] Fax: [phone]
WyreStorm Technical Support
US: [phone]
UK:- [phone]
Email: [email protected]
We reserve the right to change specification or product dimensions at any time.
1 866 677 0053
WyreStorm Oces
WyreStorm Technical Support
1 1
www.wyrestorm.com
WyreStorm Offices
US Office: 6991 Appling Farms Parkway, Suite 104, Memphis, TN 38133
Tel: + 901 384 3575 Fax: + 901 384 3574
Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK
Tel: [phone] Fax: [phone]
WyreStorm Technical Support
US: [phone]
UK:- [phone]
Email: [email protected]
We reserve the right to change specification or product dimensions at any time.
www.wyrestorm.com
WyreStorm Offices
US Office: 6991 Appling Farms Parkway, Suite 104, Memphis, TN 38133
Tel: + 901 384 3575 Fax: + 901 384 3574
Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK
Tel: [phone] Fax: [phone]
WyreStorm Technical Support
US: [phone]
UK:- [phone]
Email: [email protected]
We reserve the right to change specification or product dimensions at any time.