Wyrestorm EX-70-G2 Series User manual

4K UHD HDBaseT Extender Set
with HDCP 2.2 & 2-way PoH
EX-70-G2 Quickstart Guide
Identifying Product Versions
This product was released in 2 different versions which contain different
chassis designs and feature sets. The differences are identied throughout
this document in order to make installation and use easier. Versions can
be identied by a v# after the model number on the product chassis model
number sticker. Note that version 1 of this product may not contain a v1 after
the product while all version 2s will contain a v2 after the model number.
In the Box
1x EX-70-G2 Transmitter
1x EX-70-G2 Receiver
1x 18V DC 1A Power Supply (US/UK/EU)
1x IR Emitters
1x IR Receivers
2x 3‐pin Screw Down Male Phoenix Connectors
4x Mounting Brackets (2x for TX | 2x for RX)
1x Quickstart Guide (this document)
Basic Wiring Diagram
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 180919
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
HDMI
HDMI
IR Emitter
IR Emitter
IR Receiver
18V DC 1A
Power Supply
IR to Control System
CAB-IR-LINK (Sold Separately)
EX-70-G2 Transmitter (TX) EX-70-G2 Receiver (RX)
HDMI Source HDMI Display
KEY
HDMI
HDBaseT Cat5e/6/6a
IR TX and RX
Power
HDBaseT
Cat6/6a/7

Front Panel (TX/RX) Rear Panel (TX/RX)
Power LED Solid: The receiver is powered On
Off: The receiver is powered Off
Status LED Flashing: The receiver is operating normally.
Off: The receiver is Not operating normally.
HDCP LED
Solid: HDCP content is present.
Flashing: HDCP content is not present.
Off: No signal.
LINK LED
Solid: Link to receiver has been established.
Flashing: Link to receiver has not been
established.
Power Input
5.5mm Screw Down Barrel Jack
Connect to the included 18V DC 1A power
supply to the transmitter or receiver. A power
supply is not required on the other end as it
will be powered using PoH.
See Power Supply Wiring for important
information.
HDBT In
HDBT Out
8-pin RJ-45 female
Connect the transmitters HDBT Out to
receivers HDBT In.
IR TX/RX
IR TX - 3.5mm (1/8in) Mono Jack: Connect
to the supplied IR emitter to control a local
device from the remote display location via
HDBaseT.
IR RX - 3.5mm (1/8in) Stereo Jack: Connect
to the supplied IR receiver to send IR to the
remote display location via HDBaseT.
See IR TX/RX Guidelines for more
information.
RS-232 1x RS-232: 3-pin Phoenix (v2 chassis only)
HDMI In (TX)
HDMI Out (RX)
19-pin type A HDMI female
Supports HDMI and DVI/D (requires adapter -
not included).
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 180919
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
EX-70-G2 Transmitter
EX-70-G2 Receiver
A B C D
EX-70-G2 Transmitter
EX-70-G2 Receiver
A B C ED

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 180919
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
IR TX/RX Guidelines
• Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received by the NetworkHD
system. Other 3rd party emitters and receivers can be used; however, these
devices must operate in the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within the
port. Refer to the CAB-IR-LINK product page for more information.
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
RS-232 Wiring
The EX-70-G2 v2 uses a 3-pin RS-232 with no hardware ow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary
from device to device. Refer to the documentation for the connected device
for pin functionally to ensure that the correct connections can be made. This
connection is not available on the v1 version of this product.
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
Power Supply Wiring
The EX-70-G2 can supply power from the transmitter to the receiver using PoH on the same category cable that transmits audio and video. The included power
must be connected to the transmitter in order to power the receiver (or vise versa). Should distance of the category cable or other factors prevent PoH from
being used, connect an 18V DC 1A power supply to both devices. Additional power supplies may be purchased from WyreStorm.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that all HDMI and HDBaseT connections are not loose and are
functioning properly
• Verify that the HDBaseT cable is properly terminated following EIA568B
standard
• Verify that the output resolution of the source and display is supported by
this extender
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
• Verify that the IR and RS-232 cables are properly terminated following the
Wiring and Connections section.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
EX-70-G2 Quickstart Guide | 180919
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Specications
Audio and Video
Transmitter Receiver
Inputs 1x HDMI In: 19-pin type A 1x HDBT In: 8-pin RJ-45 Female
Outputs 1x HDBT Out: 8-pin RJ-45 Female 1x HDMI Out: 19-pin type A
Output Video Encoding HDBaseT Class B
Encoding Data Rate 9.2Gbps
End to End Latency (Max) 10μs (micro seconds)
Audio Formats 2ch PCM | Multi Channel up to Dolby Atmos®and DTS-X™
Video Resolutions (Max)
Video Resolution HDMI Cat6 Cat6a/7
1920x1080p @60Hz 12bit 15m/49ft 70m/230ft 100m/328ft
1920x1080p @60Hz 16bit 7m/23ft 70m/230ft 100m/328ft
3840x2160p @30Hz 8bit 4:4:4 7m/23ft 35m/115ft 70m/230ft
3840x2160p @60Hz 8bit 4:2:0 7m/23ft 35m/115ft 70m/230ft
4096x2160p @60Hz 8bit 4:2:0 7m/23ft 35m/115ft 70m/230ft
Supported Standards DCI | RGB
Maximum Pixel Clock HDMI: 300MHz | HDBaseT: 297MHz
Communication and Control
HDMI HDMI | HDCP (v1 chassis 1.4 | v2 chassis 2.2) | EDID Pass-through | CEC Pass-through
DVI/D supported with adapter (not included)
HDBaseT HDMI | HDCP (v1 chassis 1.4 | v2 chassis 2.2) | EDID Pass-through | 2-way PoH | Bidirectional IR
IR 1x IR TX: 3.5mm (1/8in) TS Mono | 1x IR RX: 3.5mm (1/8in) TRS Stereo
RS-232 1x RS-232: 3-pin Phoenix (v2 chassis only)
Power
Power Supply 18V DC 1A
PoH IEEE 802.3af 15.4W Max | 2-way
Max Power Consumption Transmitter: 7W | Receiver: 17W
Environmental
Operating Temperature 0 to + 45°C (32 to + 113 °F), 10% to 90%, non-condensing
Storage Temperature -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-condensing
Maximum BTU Transmitter: 24 BTU/hr | Receiver: 58 BTU/hr
Dimensions and Weight
v1 Chassis v2 Chassis
Rack Units/Wall Box <1U <1U
Height 15mm/0.6in 15mm/0.6in
Width 109mm/4.3in 108.8mm/4.29in
Depth 64.2mm/2.53in 64.2mm/2.53in
Weight 0.36kg/0.79lbs 0.36kg/0.79lbs
Regulatory
Safety and Emission CE | FCC | RoHS
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a
period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited
product warranty.
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.