Wyrestorm MX-0606-HDBT-H2L User manual

6x6/8x8 4K HDBaseT Matrix
with HDCP 2.2 support (35m/115ft)
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1 Quickstart Guide
In the Box
1x MX-0606-HDBT-H2L or MX-0808-HDBT-H2L Matrix Switcher
1x IR Remote Handset
1x IR Receiver (38Khz)
6/8x Wide-band IR Receivers (30-50KHz)
6/8x IR Emitters
1x USB to DB9 RS-232 Cable
1x 100~240V AC 50/60Hz Power Cord with US Plug
1x 100~240V AC 50/60Hz Power Cord with UK Plug
1x 100~240V AC 50/60Hz Power Cord with EU Plug
2x Mounting Brackets
1x Quickstart Guide (this document)
Basic Wiring Diagram
Key
HDMI/Digital Video
HDBaseT/Ethernet
Digital Audio
IR
RS-232
MX-0808-HDBT-H2L
RX-70-POH
Router
Control System
CAB-IR-LINK (Sold
Separately)
UHD Source
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI or HDBaseT while devices
are powered on may cause damage. WyreStorm recommends powering off
devices before disconnecting these connections.
Reccomended Products
To take full advantage of the features of this matrix, WyreStorm recommends
the following products be used within the system.
• RX-70-POH HDBaseT Receiver – Use this receiver when 4K HDCP 2.2
output is required to a display.
• CAB-IR-LINK – Use this cable when using an IR control system for matrix
control of HDBaseT pass-through.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Detailed installation and conguration information may be found in
the download tab located on the product page.
• WebUI Reference Guide – Setup for advanced Matrix features such as IP
and testing of connections
• H2 Matrix Operation User Guide – Single page document showing the
operation via front panel and included IR remote.
• Drivers and API – Precongured drivers for popular control systems and
API document.
Installation
Before Beginning
• WyreStorm recommends visiting the product page before installing this
product for updates to this Quickstart Guide as well as other information
about the product.
• Verify that all items are included in the packaging per the In the Box list.
Pre Wire
1. Run a Cat5e/6/6a cable from the matrix location to the receiver location.
See Video Resolutions in the Specications table before determining
cable type and length. Terminate the cable per the HDMI/HDBaseT
Wiring section.
2. (Optional) If using IR emitters or connecting blocks, run the wire and
terminate per the IR TX (Emitter) Wiring section.
3. (Optional) If using IR receivers at either the transmitter or receiver, run
the wire and terminate per the IR RX/Ext (Receiver) Wiring section.
4. (Optional) If using RS-232 pass-through, run the wire and terminate per
the RS-232 Wiring section.
Installation
1. Connect an HDMI source to the HDMI In on the matrix using a cable
from a high quality brand such as WyreStorm Express. Repeat for
additional sources.
2. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45
female plug to the HDBT Out jack on the matrix. Repeat for additional
HDBaseT receivers.
3. (Optional) Using the included IR emitter or the cable created in Pre Wire
step 2, place an IR emitter onto a source device near the device’s IR
sensor. Connect the 3.5mm (1/8in) Mono Plug to an IR TX port. Repeat
for additional sources.
4. Using the included IR receiver, connect the 3.5mm (1/8in) Stereo
Plug to an IR RX (IR to Zone) port. If using a control system, use the
WyreStorm CAB-IR-LINK or the cable created in Pre Wire step 3. Repeat
for additional zones.
5. (Optional) Using an included IR receiver, connect the 3.5mm (1/8in)
Stereo Plug to an IR Ext port. If using a control system, use the
WyreStorm CAB-IR-LINK or the cable created in Pre Wire step 3.
6. (Optional) Using the cable created in Pre Wire step 4, connect the 9-pin
DB9 male jack to the RS-232 port on the matrix and the opposite end to
an RS-232 control system.
7. Install HDBaseT receivers (RX-70-POH recommended) following the
instructions provided with the model being installed.
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1 Quickstart Guide | 170418
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation
process.

HDMI In
19-pin type A HDMI female:
Supports HDMI and DVI/D (requires adapter -
not included). See HDMI/HDBaseT Wiring for
important wiring guidelines.
HDBT Out
8-pin RJ-45 female
Connect to the HDBT In of an HDBaseT
receiver. See HDMI/HDBaseT Wiring for
important wiring guidelines.
HDBT Out LED Operation
Green Solid: HDBaseT link has been
established with the receiver.
Green Flashing or Off: HDBaseT link has NOT
been established with the receiver.
Amber Flashing: HDBaseT functioning
normally and can establish a link with the
receiver.
Amber Off: HDBaseT has discovered a fault
and cannot establish a link with the receiver.
IR RX/Ext/TX
IR RX/Ext - 3.5mm (1/8in) Stereo Jack:
Connect to an IR receiver for matrix control
(Ext) or IR pass-through (RX) via HDBaseT.
IR TX - 3.5mm (1/8in) Mono Jack:
Connect to an IR emitter to control a local
device from the remote display location via
HDBaseT. See IR Wiring.
Update/RS-232
Mode
Normal: RS-232 Matrix control.
Update: RS-232 rmware update.
Dials: Selects card position to update.
LAN 8-pin RJ-45 female | 10/100 Mbps auto-
negotiating
EDID
4 Position Dipswitch:
Used to set EDIDs to correct resolution
conflicts between the source and the display.
See EDID Settings.
RS-232
9-pin DB9 Female
Used to control the matrix functions and
rmware updates.
Power
Power Switch: 0 –Power Off / I – Power On
Fuse Holder
IEC Power Cord Port
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1 Quickstart Guide | 170418
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
Front Panel
Rear Panel
Output Channel
Indicator
1-6 (6x6) or 1-8 (8x8)
Displays the source input number currently selected for the corresponding output number.
IR Sensor Receives IR signals from included handheld IR remote or attached emitter from IR control system for switcher control.
Source/Output
Navigation
Left/Right: Output Selection
Up/Down: Input Selection
Enter: Conrm Selection
A B C
A B C D E F G H

HDMI/HDBaseT Wiring
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference can have an adverse effect on
HDMI or HDBaseT transmission limiting performance. Steps should be
taken to minimize these factors (or remove completely) during installation
for best results.
• WyreStorm recommends using high quality HDMI cables such as
WyreStorm Express to ensure the highest content performance available.
• The type of category cable and length used can restrict the available video
resolution. While Cat5e can be used, WyreStorm recommends using Cat6
or higher to ensure the highest content performance available. See Video
Resolutions in the Specications table before determining cable type and
length.
Pin 1
Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
IR Wiring
IR TX (Emitter) Wiring
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: Anode/5V
Sleeve: Cathode/IR Signal
IR RX (Receiver) Wiring
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
IMPORTANT! IR TX Connection Guidelines
• 3rd party IR receivers may require a different voltage, refer to the
documentation provided with the IR receiver before making any
connections to avoid damaging the device.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
RS-232 Wiring
Most control systems and computers are DTE where pin 2 is RX, this can vary
from device to device. Refer to the documentation for the connected device
for pin functionally to ensure that the correct connections can be made.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
TX (Transmit)
RX (Receive)
-------
-------
GND (Ground)
Outside of DB9
male port shown.
-------
-------
-------
Pin 9: -------
5
9
8
7
6
4
3
2
1
EDID Settings
EDIDs can be congured to resolve issues with video output on displays that
may not accept the maximum resolution available from the source.
• When set to Smart EDID (default) the matrix will scan all selected displays
for the lowest resolution.
• When EDID Copy or a direct EDID is being used, SmartEDID is turned Off.
• Ensure that a display is connected and powered On to the selected output
before copying EDIDs or the copy will fail. When this occurs, EDID will be
set to 4K@30Hz 2ch.
• Power to the matrix must be cycled (Off/On) after changing dip switches in
order for the setting to take effect.
Smart EDID-Display
Lowest Resolution - 2ch
only (default)
1080i 2ch
4K UHD
4K @60Hz 2ch
No HDR
4K @30Hz 7.1ch
With HDR
4K @30Hz 5.1ch
With HDR
4K @30Hz 2ch
With HDR
4K @30Hz 8bit 2ch
No HDR
1080p
1080p @60Hz 7.1ch 1080p @60Hz 5.1ch
1080p @60Hz 2ch
Standard Video
1920x1200 2ch 1920x1200 No Audio
Copying EDIDs
1. Set the EDID dipswitch to the Front Panel, Web UI or API EDID Control
(all switches up).
2. Reboot the matrix.
3. Using the front navigation buttons, select the input port for the output.
Example: Input 2 for Output 2
4. Once the output port indicator blinks, press and hold Enter for 5
seconds. An OK message on the display indicates that the copy was
successful, an FL-2 indicates that the copy failed.
5. Reboot the matrix.
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1 Quickstart Guide | 170418
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4

Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit repair,
component replacement or complete product replacement in the event of malfunction. The decision to repair or replace will
be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and excludes normal
wear and tear or cosmetic damage. Visit the product page located at wyrestorm.com for additional information on this
product including important technical information not provided in this document and warranty terms & conditions.
Specications
Copyright © 2017 WyreStorm Technologies | wyrestorm.com
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1 Quickstart Guide | 170418
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the matrix and receiving device and
that both devices are powered on.
Note: When using PoH to power the transmitter, verify that the HDBaseT cable
is properly terminated per the HDMI/HDBaseT Wiring section.
• Verify that the transmitter, matrix/receiver, and display support the output
resolution of the source. Refer to Video Resolutions in the Specications
table for the max distance based on resolution.
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
• Verify that the HDBaseT cable is properly terminated per the HDMI/
HDBaseT Wiring section.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
• Verify that the IR and RS-232 cable(s) are properly terminated per the
appropriate wiring section.
- IR: IR Wiring.
- RS-232: RS-232 Wiring
• Verify that the IR emitter is located over or near the IR sensor on the device.
Move the emitter closer or further from the sensor as the IR signal can be
too strong in some cases.
• Verify that the IR receiver is in line of sight of the handheld remote.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
• Use a flashlight to locate the IR receiver behind any tinted panels on the
device being control.
Power
Power Supply Input: 100~240V AC 50/60Hz
PoH 48V 15.4W (each HDBT output)
Max Power Consumption 120W
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%,
non-condensing
Storage Temperature -4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%,
non-condensing
Maximum BTU 409.4 BTU/hr
Dimensions and Weight
Rack Units/Wall Box 2U
Height With | Without Feet 95.7mm/3.7in | 87.7mm/3.4in
Width With | Without Rack Ears 487.2mm/19in | 438mm/17.1in
Depth With | Without Handles 423.7mm/16.5in | 397.5mm/15.5in
Weight 8.2kg/18.04lbs
Regulatory
Safety and Emission CE | FCC | RoHS
Audio and Video
Inputs 6/8x HDMI 19-pin type A
Outputs 6/8x HDBaseT 8-pin RJ-45 female
Audio Formats 2ch PCM | Up to DTS-X and Dolby Atmos
Output Video Encoding HDBaseT Class B
Encoding Data Rate 10.2Gbps
End to End Latency 10μs (micro seconds)
Video Resolutions (Max)
HDMI
1920x1080p @60Hz 12bit (15m/50ft) | @60Hz 16bit (7m/23ft)
3840x2160p @30Hz 4:4:4 8bit (7m/23ft) | @24Hz 4:2:0 HDR 10bit per channel (3m/9.8ft)
4096x2160p @60Hz 8bit 4:2:0 (7m/23ft) | @60Hz 8bit 4:4:4 (3m/9.8ft)
Using Cat6
1920x1080p @60Hz 12bit (70m/230ft) | 16bit (35m/114ft)
3840x2160p @30Hz 4:4:4 8bit (35m/114ft) | @24Hz 4:2:0 HDR 10bit (35m/114ft)
4096x2160p @60Hz 4:2:0 8bit (35m/114ft)
Using Cat6a/7
1920x1080p @60Hz 12bit (70m/230ft) | @60Hz 16bit (40m/131ft)
3840x2160p @30Hz 4:4:4 8bit (40m/131ft) | @24Hz 4:2:0 HDR 10bit (40m/131ft)
4096x2160p @60Hz 4:2:0 8bit (40m/131ft)
Color Depth 1080p: 16bit | 4K UHD: 8bit | HDR @24p: 10bit BT.2020
Maximum Pixel Clock HDMI: 600mHz | HDBaseT: 297MHz
Communication and Control
HDMI HDMI 2.0 | HDCP 2.2 | EDID | DVI/D supported with adapter (not included)
HDBaseT HDCP 2.2 | EDID | 1-way PoH | Bidirectional IR
IR 1x IR Ext - 3.5mm (1/8in) Stereo | Matrix Control
6/8x IR TX - 3.5mm (1/8in) Mono | 6/8x IR RX - 3.5mm (1/8in) Stereo | Bidirectional over HDBaseT
RS-232 Matrix Control | Firmware Updates