Wyrestorm RXV-70-4K User manual

PDF provided by Conference Room AV
WyreStorm RXV-70-4K HDMI Over HDBaseT Receiver - 328'

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the
installation process.
Basic Wiring Diagram
Quickstart Guide
RXV-70-4K
4K HDR HDMI-Over-HDBaseT Receiver
with HDCP 2.2 and PoH
HDBaseT Cat6/6a/7
Control
Power
Key
HDMI/Digital Video
HDBaseT/Ethernet
MX-1616-H2XC
with TX-H2X-VLC
Modular Card
Control System
IR RX
CAB-IR-LINK (Sold Separately)
RXV-70-4K
HDR Display
HDMI
Ethernet
IR RX IR TX
Note: Not required if powering
the receiver via PoH.
12V DC 2A
Power Supply
IMPORTANT! Installation Requirements
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
In the Box
1x RXV-70-4K Receiver
1x IR Emitter
1x IR Receiver
2x Mounting Brackets
1x 3-pin Phoenix Connector
1x Quickstart Guide (this document)

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
2 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results
• WyreStorm recommends using pre-terminated HDMI and DP cables due to
the complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
IR TX/RX Guidelines
• Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received Other 3rd party
emitters and receivers can be used; however, these devices must operate in
the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within
the port. Refer to the CAB-IR-LINK product page for more information.
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
RS-232 Wiring
The RXV-70-4K uses a 3-pin RS-232 with no hardware ow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary
from device to device. Refer to the documentation for the connected device
for pin functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
3 of 4
EDID Conguration
This receiver uses EDID pass-through from the display to the source. No conguration is required for EDID settings.
Setup and Conguration
RS-232 Mode Settings
The RS-232 connector is used to transmit RS-232 over HDBaseT to the remote
location and for rmware updates. Ensure that the RS-232 Mode switch in
the proper position for the operation being performed. This connection is only
available on version 1 of this product.
Set the mode switch to Normal to transmit RS-232
signals from the TX to the RX for controlling devices in
the remote location.
Set the mode switch to the Update position to install a
rmware update in either the TX or RX.
Troubleshooting
No or Poor-Quality Picture (snow or noisy image)
• Verify that power is being supplied to the transmitter and receiver.
• Verify that the ber cable is properly terminated.
• Verify that the output resolution of the source and display is supported by
this extender.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
• Verify that the RS-232/Ethernet cables are properly terminated.
• Verify that emitters/receivers are compatible with WyreStorm IR.
• If using an IR control system, verify that it is connected using the CAB-IR-
LINK cable.

Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: [phone] | ROW: 844.280.WYRE (9973)
[email protected]
4 of 4
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a
period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited
product warranty.
Specications
Note: WyreStorm reserves the right to change product specication, appearance or dimensions of this product at any time without prior notice.
Audio and Video
Inputs 1x HDBT In: 8-pin RJ-45 Female
Outputs 1x HDMI Out: 19-pin type A
Input Video Encoding HDBaseT Class A
Encoding Data Rate 9.2Gbps
End to End Latency 10μs (micro seconds)
Audio Formats 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos
Video Resolutions (Max)
Resolution HDMI Cat6 Cat6a/7
1920x1080p @60Hz 12bit 15m/49ft 100m/328ft 100m/328ft
1920x1080p @60Hz 16bit 7m/23ft 70m/230ft 100m/328ft
3840x2160p @24Hz 10bit 4:2:0 HDR 3m/10ft 70m/230ft 100m/328ft
3840x2160p @30Hz 8bit 4:4:4 7m/23ft 70m/230ft 100m/328ft
3840x2160p @60Hz 10bit 4:2:0 HDR 3m/10ft 70m/230ft 100m/328ft
4096x2160p @60Hz 8bit 4:2:0 7m/23ft 70m/230ft 100m/328ft
4096x2160p @60Hz 8bit 4:4:4 7m/23ft 70m/230ft 100m/328ft
Supported Standards DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
Maximum Pixel Clock HDMI: 600MHz | HDBaseT: 297MHz
Communication and Control
HDMI HDCP 2.2 | EDID | CEC | DVI-D supported with adapter (not included)
HDBaseT HDMI | HDCP 2.2 | EDID | CEC | 1-way PoH to Receiver | Bidirectional IR
CEC CEC Pass-through – Requires CEC compatibility between source and display
Ethernet 1x Ethernet: 8-pin RJ-45 Female | Bidirectional over HDBaseT
IR 1x IR RX 3.5mm (1/8in) TRS Stereo | 1x IR TX: 3.5mm (1/8in) TS Mono | Bidirectional over HDBaseT
RS-232 1x RS-232: 3-pin Phoenix | Bidirectional over HDBT
Power
Power Supply 12V DC 2A
PoH 48V 15.4W
Max Power Consumption 8.68W
Environmental
Operating Temperature 0 ~ +45°C (32 ~ +113 °F) | 10% ~ 90% non-condensing
Storage Temperature -20 ~ +70°C (-4 ~ +158 °F) | 10% ~ 90% non-condensing
Maximum BTU 29.6 BTU/hr
Dimensions and Weight
Rack Units | Wall Box <1U
Height With | Without Feet 20.5mm/0.81in | 20mm/0.79in
Width With | Without Brackets 193mm/7.6in | 150mm/5.91in
Depth With | Without Handles 74.4mm/2.93in | 74.4mm/2.93in
Weight 0.4kg/0.88lbs
Regulatory
Safety and Emission CE | FCC | RoHS