X-keys XK-24 User manual

XK-24 Programmable Keypad KVM
Product Manual
Part# XK-0994-UKVM-R
24 Keys
USB Keyboard
Blue or Red Backlighting
Designed, Sold, and Supported in USA
From P.I Engineering, The No Slogan Company
www.xkeys.com
Box Contents
This package contains:
1- X-keys XK-24 KVM Version
1- Replacement key set (2 tall, 1 wide, 1 key puller)
1 –Software Disc
2- Angled feet
2- Legend Sheet (1 blank, 1 pre-printed)
1- Product Manual (this document)
Software
Install MacroWorks .3.1 from the enclosed disc or download the newest
version from: xkeys.com/PISupport/SoftwareMacroWorks.php
IMPORTANT
To put this XK-24 into programming mode, hold down the programming button
(the black button on the top edge of the X-keys) while plugging it into a USB
port. After MW3.1 writes your macros to the XK-24 memory, unplug the XK-24
to return it to keyboard mode.
Once programmed, the XK-24 may be plugged into any system and it will play
back programmed keystrokes just like any standard USB keyboard.
Backlighting
The XK-24 has two backlighting colors (red and blue). The factory setting is
blue at full intensity. You may change the intensity level or turn on or off either
set of LEDS with “Hardware Default Backlighting” settings under the Unit Data
tab in MW3.1. Be sure to click the “Save Backlighting” button to write your
settings to the XK-24s memory.

2
Support
Should you encounter difficulty with the installation or programming, please
check the MW3.1 Help File or check the troubleshooting guide on our web
site. You may also contact our technical support department.
E-mail: [e-mail] Phone: [phone]
Compatibility
X-keys USB devices are compatible with any computer or host system which
supports USB HID Keyboard input. For more information contact our
Technical Support Department ([e-mail]).
Identifying the Keys
Select appropriate icons or use the blank side of the legend sheet to create
your own key legends. The keycaps snap off with a fingernail or small
screwdriver. Apply the label under the keycap, and replace it. The key caps
hold a legend 0.575" wide and 0.5" high (14.6mm x 12.7mm). Other options
are available for printing legends for multiple units. Contact our Sales
Department ([e-mail]) for more information.
Horizontal and Vertical Double-keys
The included double-keys replace two single keys on the X-keys. To install a
double key cap, remove two adjacent keys with the provided key-puller.
Pressing the key puller over an adjacent key and working it under the cap to
be removed is the recommended method. Press the double-key in place over
the two exposed switch stems.
Key Blockers
Unused keys may be replaced with optional key blockers and identified as
blocked keys in MW3.1.
Feet
The included angled feet may be snapped in to the bottom of the XK-24 to
give it a slight tilt in either portrait or landscape orientation.

3
Compatible Accessories
Please visit the Accessories page on our website for details on the following.
Tall and wide keycaps
Colored and transparent key caps
Blank key blockers
Other Products from P.I. Engineering
X-keys XK-24 –24 programmable keys
X-keys XK-60 –60 programmable keys
X-keys XK-80 –80 programmable keys
X-keys XK-128 –128 programmable keys
X-keys XK-12 Joystick –12 keys with a precision joystick
X-keys XK-12 Jog & Shuttle –12 keys with jog & shuttle
X-keys XK-12 Touchpad –12 keys with touchpad
X-keys XK-3 Foot Pedal –three programmable pedals
X-keys XK-4 Stick –four programmable keys
X-keys XK-8 Stick –eight programmable keys
X-keys XK-16 Stick –sixteen programmable keys
X-keys XK-68 Jog & Shuttle –68 keys with jog & shuttle
X-keys XK-68 Joystick –68 keys with a precision joystick\
X-keys Matrix Board –128 switch points
Y-mouse PS/2 to USB adapter
FCC Declaration of Conformity
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instruction manual may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio TV technician for help.
Any changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.

4
Contact Us
Sales
E-mail:
[e-mail]
Phone: [phone] or
1-517-655-5523
FAX: [phone]
Technical Support
Web: www.piengineering.com
E-mail:
[e-mail]
Phone: [phone]
Our Shipping Address
P.I. Engineering
101 Innovation Parkway
Williamston, MI 48895-1663
USA
Limited Warranty
For all X-keys products purchased and installed in the United States and Canada, P.I. Engineering
warrants that the X-keys product will be free from defects in materials and workmanship under
normal use and service, and will meet the specifications presented by P.I. Engineering at the time
of original purchase, for one year as evidenced by a copy of the purchase receipt. Under this
warranty, P.I. Engineering will, at its sole option, repair or replace any X-keys product which is
defective, provided that you are responsible for (i) the cost of transportation of the product to
P.I. Engineering or its designated service facility, and (ii) any loss or damage to the product
resulting from such transportation.
Upon discovery of a defect in the product within the Warranty Period, you should notify
P.I. Engineering Technical Support via telephone to obtain an RMA (return authorization number)
and instructions for shipping the product to a service location designated by P.I. Engineering. You
should send the product, shipping charges prepaid, to the designated location, accompanied by
the return authorization number, your name, address, and telephone number, proof of purchase,
and a description of the defect. P.I. Engineering will pay for return of product(s) to the customer.
P.I. Engineering shall have no responsibility to repair or replace the X-keys product if the failure
has resulted from accident, abuse, mutilation, misuse, or repair/modification performed by any
entity other than P.I. Engineering.
THIS WARRANTY IS EXCLUSIVE OF ALL OTHER WARRANTIES, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.
P.I. ENGINEERING DOES NOT WARRANT THIS X-keys PRODUCT FOR FITNESS FOR A PARTICULAR PURPOSE OR
MERCHANTABILITY. P.I. ENGINEERING AND ITS EMPLOYEES SHALL NOT BE HELD LIABLE FOR ANY CONSEQUENTIAL,
INDIRECT, OR INCIDENTAL DAMAGES, EVEN IF ADVISED OF THEIR POSSIBILITY, ARISING OUT OF THE USE OR
INABILITY TO USE THIS PRODUCT. SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR LIMITATION OF CERTAIN
LIABILITIES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO STATE.
In the event that the above limitations are held unenforceable, P.I. Engineering’s liability for any damages to you or to any party
shall not exceed the purchase price you paid, regardless of the form of any claim.
This limited warranty is valid for and only applies to products purchased and used inside the United States (and its territories) and
Canada.
This limited warranty is governed by the laws of the United States of America and the state of Michigan.
X-keys Electronic design: P.I. Engineering, Inc., Williamston, Michigan
Patent # 4964075
© 2014P.I. Engineering, Inc. All rights reserved.
Y-mouse, Y-see two, Y-key key, X-keys, and the “P.I. Eclipse” are trademarks of P.I. Engineering, Inc.
PS/2 is a registered trademark of International Business Machines, Inc.
All other trademarks are property of their respective owners.
www.piengineering.com ◘ www.xkeys.com
www.ymouse.com ◘ www.raildriver.com
PI Part#0970