X-Rite DTP32 User manual

X-Rite World Headquarters © 1995 X-Rite, Incorporated Doc# DI00012a.doc
[phone] Fax [phone] August 18, 1995
Interfacing the DTP32/DTP12 with the Seiko DPU-411 Thermal Printer
To interface the DTP unit to send output to a Seiko DPU-411 Thermal Printer, you must first
set-up three things: 1) connect the two devices with the correct cabling and adapters, 2) set
the dip switches on the DPU-411 correctly, and 3) configure the communications set-up on the
DTP unit.
Cabling
To connect the DTP32 or DTP12 to the Seiko printer you will need a 418-69 cable and a 418-
80 converter from X-Rite. Plug the 418-80 into the RS 232 port in the back of the Seiko
Printer. Next plug the cable in; one end to the DTP unit, the other to the adapter plugged into
the printer. It will not matter which end goes to which device.
Setting the DPU's Dip Switches
Next you must set the dip switches found on the bottom of the Seiko DPU-411 Thermal
Printer. Turning the printer over you will notice two sets of dip switches. The first set of
switches are labeled 1 through 8. The second set is labeled 1 through 6. Switches pushed up
(towards the word "ON") are on, while switches in the down position are off. Set the switches
as follows:
1: OFF 1: ON
2: OFF 2: ON
3: ON 3: OFF
4: ON 4: OFF
5: OFF 5: ON
6: OFF 6: ON
7: ON
8: ON
Configuring the DTP
To configure the DTP unit we must go to the configure menu. Start by pressing the two right-
most buttons on the DTP unit at the same time. This will get you to Page one of the MAIN
MENU. Now press the left-most button twice to scroll you to page 3 of the Main Menu. The
display should read "p3 cnfg edit". Press the button under the word "cnfg" to enter the configu-
ration menu.
®
Interfacing the DTP32/DTP12 with the Seiko
DPU-411 Thermal Printer
Author - Michael DiCosola

X-Rite World Headquarters © 1995 X-Rite, Incorporated Doc# DI00012a.doc
[phone] Fax [phone] August 18, 1995
Check the following fields to ensure proper communication:
•Press the button under the word "TYPE". If "TYPE" does not change to "ser", continue to
press the same button until it does read "ser".
•Press the left-most button to continue.
•Press the button under the word "BAUD". If "BAUD" does not change to "1200", continue
to press the same button until it does read "1200".
•Press the button under the word "HAND". If "HAND" does not change to "xon", continue to
press the same button until it does read "xon".
•If the last word on the display, "axmt", is spelled in all capital letters, press the button be-
neath "AXMT" until the word changes from capital letters to lower case letters.
•Press the left-most button to continue.
•Press the button under the word "DLIM". If "DLIM" does not change to "crlf", continue to
press the same button until it does read "crlf".
•Press the two left-most buttons at the same time to save these configuration settings.
Sending Data to the Printer
After reading an auto scannable test strip the DTP will automatically display your readings.
Use the up or down arrows to view the separate reading of each strip. Use the right most but-
ton to toggle between different strips if you scanned more than one strip. Pressing the button
under the word "xmit" will transmit your data to the Seiko printer. The word will temporarily
change to all capitals and the Seiko will begin printing your output.