Xerox DocuPrint 92C Technical manual

Xerox DocuPrint Network Printer Series
Installation Planning Guide
for Model 92C NPS
Version 7.1
$XJXVW 2000
721P87421

Xerox Corporation
701 South Aviation Boulevard
El Segundo, CA 90245
¸ 2000 by Xerox Corporation. All rights reserved.
Copyright protection claimed includes all forms and matters of
copyrightable material and information now allowed by statutory or
judicial law or hereinafter granted, including without limitation,
material generated from the software programs which are displayed
on the screen, such as icons, screen displays, looks, etc.
Printed in the United States of America.
Publication number: 721P87421
Xerox
·, The Document Company, the stylized X, and all Xerox
product names mentioned in this publication are trademarks of Xerox
Corporation. Products and trademarks of other companies are also
acknowledged.
Changes are periodically made to this document. Changes, technical
inaccuracies, and typographic errors will be corrected in subsequent
editions.

XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS iii
Laser safety
!Warning: Adjustments, use of controls, or performance of
procedures other than those specified herein may result in
hazardous light exposure.
The Xerox DocuPrint printers are certified to comply with the
performance standards of the U.S. Department of Health, Education,
and Welfare for Class 1 laser products. Class 1 laser products do not
emit hazardous radiation. The DocuPrint printers do not emit
hazardous radiation because the laser beam is completely enclosed
during all modes of customer operation.
The laser danger labels on the system are for Xerox service
representatives and are on or near panels or shields that must be
removed with a tool. DO NOT REMOVE LABELED PANELS OR
PANELS NEAR LABELS. ONLY XEROX SERVICE
REPRESENTATIVES HAVE ACCESS TO THESE PANELS.
Ozone information
This product produces ozone during normal operation. The amount
of ozone produced depends on copy volume. Ozone is heavier than
air. The environmental parameters specified in the Xerox installation
instructions ensure that concentration levels are within safe limits. If
you need additional information concerning ozone, call 1-800-828-
6571 to request the Xerox publication 600P83222, OZONE.
Operation safety
Your Xerox equipment and supplies have been designed and tested
to meet strict safety requirements. They have been approved by
safety agencies, and they comply with environmental standards.
Please observe the following precautions to ensure your continued
safety.
•Always connect equipment to a properly grounded electrical
outlet. If in doubt, have the outlet checked by a qualified
electrician.
!Warning: Improper connection of the equipment grounding
conductor may result in risk of electrical shock.
•Never use a ground adapter plug to connect equipment to an
electrical outlet that lacks a ground connection terminal.
•Always place equipment on a solid support surface with
adequate strength for its weight.



iv XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
•Always use materials and supplies specifically designed for
your Xerox equipment. Use of unsuitable materials may result in
poor performance and may create a hazardous situation.
•Never move either the printer or the Printer Controller without
first contacting Xerox for approval.
•Never attempt any maintenance that is not specifically
described in this documentation.
•Never remove any covers or guards that are fastened with
screws. There are no operator-serviceable areas within these
covers.
•Never override electrical or mechanical interlocks.
•Never use supplies or cleaning materials for other than their
intended purposes. Keep all materials out of the reach of
children.
•Never operate the equipment if you notice unusual noises or
odors. Disconnect the power cord from the electrical outlet and
call service to correct the problem.
If you need any additional safety information concerning the
equipment or materials Xerox supplies, call Xerox Product Safety at
the following toll-free number in the United States:
1-800-828-6571
For customers outside the United States, contact your local Xerox
representative or operating company.

XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS v
Table of Contents
Laser safety iii
Ozone information iii
Operation safety iii
Introduction ix
About this guide ix
Contents ix
Conventions x
Notice x
1. Product overview 1-1
System overview 1-1
Client workstations and system software 1-3
Supported hardware and operating systems 1-3
Client networking software 1-4
Ethernet LAN 1-4
Token Ring 1-5
Fiber Distributed Data Interface 1-5
NPS/IPS Dual Mode 1-5
Sixth Sense 1-5
2. Controller components and options 2-1
Controller hardware 2-1
Sun Ultra 2 workstation 2-1
Sun Ultra 60 workstation 2-4
Controller software 2-9
3. Printer components and options 3-1
Printer components 3-1
Printer control console 3-3
Printer options 3-4
High-capacity feeder 3-4
Dual stacker 3-5
Stitcher/stacker 3-6
Customer-changeable unit (CCU) 3-7
Bypass transport option 3-8
Interface with third-party devices 3-9
Electrical interface 3-9

TABLE OF CONTENTS
vi XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
4. Preparing for installation 4-1
Responsibilities 4-1
Xerox responsibilities 4-1
Customer responsibilities 4-2
Installation planning checklist 4-4
NPS network installation checklist 4-7
Novell network information 4-9
DocuPrint as a print server (PSERVER) 4-9
DocuPrint NPS as a remote printer (RPRINTER) 4-10
Connectivity requirements 4-12
Ethernet specifications 4-12
Token Ring specifications 4-12
Fiber Distributed Data Interface specifications 4-12
5. Controller specifications and requirements 5-1
Power requirements 5-1
Outlet configurations 5-2
Environmental specifications 5-3
Space requirements 5-3
Printer controller placement 5-3
Controller hardware specifications and requirements summary 5-7
6. Printer specifications and requirements 6-1
Power requirements 6-1
Outlet configurations 6-2
Printer outlet voltages—60 Hz 6-2
Printer outlet voltages—50 Hz 6-3
Environmental specifications 6-4
Space requirements 6-5
Printer placement 6-5
CCU changeout cart 6-10
Space planning guidelines 6-11
Clearance space requirements 6-11
Shared space 6-11
Floor leveling 6-15
Delivery access requirements 6-15
Printer hardware specifications and requirements summary 6-18
Space planning templates 6-19
7. System connections 7-1
Cable lengths 7-1
Cable locations 7-2

TABLE OF CONTENTS
XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS vii
8. Installation 8-1
Installation process 8-1
Your responsibilities 8-2
Software licensing 8-3
Ongoing maintenance 8-4
Routine maintenance 8-4
Meter reading and reporting 8-4
A. Supplies A-1
Paper and other throughput stocks A-1
Selecting paper A-1
Paper care A-3
Other supplies A-6
Dry ink A-6
Fuser lubricant A-6
Developer A-6
Stitcher wire A-7
Diskettes A-7
Tapes A-7
Fonts A-8
Consumable supplies tables A-9
Paper and special stocks tables A-9
Complete supplies list—Model 92C printer A-12
Ordering supplies A-14
B. Xerox support services B-1
Xerox Customer Service Support Center B-1
Xerox Printing Systems Customer Support Center B-2
Xerox Customer Documentation Catalog B-3
Xerox Documentation and Software Services (XDSS) B-3
Operator training B-3
Xerox Customer Education B-4
Xerox Font Center B-4
C. Related publications C-1
D. DocuPrint NPS on a Novell network D-1
Novell NetWare overview D-1
Print queues D-1
Queue to printer relationships D-2
PCONSOLE D-2
Print server (PSERVER) D-3
Job parameters D-3

TABLE OF CONTENTS
viii XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
Using Novell forms to specify virtual printers D-4
Remote printer (RPRINTER) D-4
DocuPrint NPS as a print server or as a remote printer D-5
Choosing a Print Server or Remote Printer Configuration D-5
Novell configuration D-7
Configuring DocuPrint as a PSERVER D-7
Configuring DocuPrint as an RPRINTER D-9
Supporting DocuPrint NPS on the file server D-10
Glossary GLOSSARY-1
Index INDEX-1

XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS ix
Introduction
This guide helps you prepare for delivery and installation of your new
Xerox DocuPrint printing system.
About this guide
This guide is intended for the person responsible for coordinating the
installation of the DocuPrint printer at your site. It lists the tasks you
must complete before installation can begin, as well as your
responsibilities during the installation.
Before using this guide, become familiar with its contents and
conventions.
Contents
This guide contains the following:
•Chapter 1, "Product overview," provides an overview of the
printing system.
•Chapter 2, "Controller components and options," describes
system controller hardware, software, and options of your
printing system.
•Chapter 3, "Printer components and options," describes printer
components, configurations, and options.
•Chapter 4, "Preparing for installation," provides a checklist of
tasks that must be accomplished before the installation. It also
explains connectivity requirements for transporting documents
from the host or client to the DocuPrint printing system.
•Chapter 5, "Controller specifications and requirements,"
describes power, environmental, and space requirements for
the system controller.
•Chapter 6, "Printer specifications and requirements," describes
power, environmental, and space requirements for the printer.
Space planning guidelines and diagrams are provided to help
you set up the work area.
•Chapter 7, "System connections," provides cable requirements
for your printing system.
•Chapter 8, "Installation," describes the activities that occur
during installation. It also describes ongoing maintenance
activities.
•Appendix A, "Supplies," describes how to select, store, and use
supplies for the DocuPrint printing system. It also provides a list
of consumable supplies you can order.

INTRODUCTION
x XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
•Appendix B, "Xerox support services," explains how to utilize
available Xerox support services.
•Appendix C, "Related publications," lists other Xerox
documents that are part of this publication set.
•Appendix D, "DocuPrint NPS on a Novell network," describes
some of the considerations to make before the installation of
DocuPrint on a Novell network.
A glossary and index are provided at the back of the guide.
Conventions
This guide uses the following conventions:
•Italics—Document and library names are shown in italics (for
example, the Xerox DocuPrint IPS Series Messages Guide).
•Capitalization of graphical user interface (GUI) window titles
matches the titles as they appear on the screen. In cases where
a window does not have a title, it is referenced using all lower
case. For example:
—At the graphical user interface, use the Output
Configuration window to group the trays.
—The main window displays the current system status.
Note: Notes are hints that help you perform a task or understand
the text.
Caution: Cautions alert you to an action that could damage
hardware or software.
!Warning: Warnings alert you to conditions that may affect the
safety of people.
Notice
This publication may contain descriptions of concepts and features
not currently available for your Xerox printing system. Consult your
Xerox sales representative or your operating system software
program description for additional information.


XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS 1-1
1. 1Product overview
This chapter provides an overview of the features and functions of
the Xerox DocuPrint Model 92C NPS.
System overview
The DocuPrint system enables personal computer (PC), Sun
Workstation, DEC workstation, HP/Apollo, IBM RS/6000, and Apple
Macintosh users to print PostScript level 2, HP PCL5e, or ASCII
documents on a high-speed Xerox DocuPrint Model 92C NPS
printer.
One or more of the following network communication systems may
be used to transport documents from the client workstation to the
printer:
•Ethernet local area network (LAN) running Transmission
Control Protocol/Internet Protocol (TCP/IP), AppleTalk, or
Novell NetWare network protocol software.
•Token Ring running TCP/IP, Novell, or AppleTalk network
protocol software.
•Fiber Distributed Data Interface (FDDI) running TCP/IP, Novell
3.x, or Apple Talk network protocols. The FDDI supports a
Single Connection configuration only.
Multiple network devices may be installed on the same NPS
controller. The default network device that ships with your NPS
controller is a 100 Mbit Ethernet connection. You may install other
network devices by installing additional network cards, provided each
card has a unique network to which it connects. For example, if you
use a Token Ring network connection, you have the option of using
the default Ethernet device as a secondary network.
If you choose to install multiple network devices on your NPS
controller, the following parameters apply:
•You must select a primary network device and designate any
others as secondary. The primary network device does not
have to be the default Ethernet device that ships with your
controller; it can be any of the network devices installed.
•You must run the TCP/IP protocol on the primary network
device. You may also run TCP/IP on other network devices. For
each network device running TCP/IP, you must specify a unique
IP address and IP netmask. For the primary network device,
you must specify the HostName and router IP address. The
HostName for any secondary devices is created from the name
chosen for the primary device.

PRODUCT OVERVIEW
1-2 XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
Note: You may not use the NPS controller as an IP router.
Consequently, the router IP address must be on the primary
network devices network only.
•You may run the AppleTalk protocol on only one network device.
The network device on which AppleTalk is run does not have to
be the primary network device.
•You may run Novell protocols on only the primary network
device.
Figure 1-1. DocuPrint printer system components
1 Customer-supplied client PC or workstation
2 Customer-supplied network
3 Xerox-supplied printer controller
4 Xerox-supplied printer interface
5 DocuPrint Model 92C printer.
Briefly, the functions of the components are as follows:
Customer-supplied client PC or
workstation
Users create their documents at the networked client PCs or
workstations using software applications that generate PostScript
(XGF), HP PCL5e, or ASCII output. When ready to print, users
submit the documents to the printer controller.
Customer-supplied network The customer will need to supply one or more of the following
networks:
•Ethernet local area network (LAN) running TCP/IP, AppleTalk,
or Novell NetWare network protocol.
•Token Ring running TCP/IP, Novell, or AppleTalk network
protocol.
•Fiber Distributed Data Interface (FDDI) running TCP/IP, Novell
3.x, or Apple Talk network protocols. The FDDI supports a
Single Connection configuration only.
Xerox-supplied printer controller Printer controller (color or monochrome monitor, processor, CD-
ROM drive, keyboard, mouse, optional 1/4-inch or 4mm tape drive):
The printer controller accepts the print job from the client workstation,
converts the files into page images, and sends the page images to
the printer. The user interface at the printer controller allows you to
perform tasks such as monitoring job status, prioritizing jobs, and
configuring the system. The optional cartridge tape drive can be used
for tasks such as backing up files. The CD-ROM drive also allows you
to install the printer controller software.

PRODUCT OVERVIEW
XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS 1-3
Xerox-supplied printer interface The printer interface cable provides high-speed data transport and
communication between the printer controller and the printer.
Xerox-supplied DocuPrint printer The printer (also known as an IOT or print engine) accepts data from
the printer controller and prints the document according to the print
options specified by the user. The printer also provides paper
stacking, collating, and optional finishing.
DocuPrint Network Printing System
(NPS)
The entire DocuPrint Network Printing System includes the printer
(also known as an IOT or print engine), printer controller, printer
interface, and all appropriate software. “DocuPrint printer”or “printer”
refers to the base printer engine (IOT) only, without the printer
controller and interface.
Note: It is your responsibility to supply, install, and maintain
hardware and software on any PC, DECStation, Sun Workstation,
HP/Apollo Workstation, IBM RS/6000 Workstation, or Macintosh
system used to generate documents for printing on the DocuPrint
printers. You are also responsible for obtaining, installing, and
maintaining the required Ethernet LAN or Token Ring network,
transceivers, cables, and connectors, as well as any necessary FDDI
connectors.
Xerox is responsible for the physical installation and service of the
printer and printer controller hardware and software components.
You have the general responsibility for the site of ensuring that the
right personnel, supplies, and that network hardware and software is
available. Refer to the “Preparing for installation”chapter of this
guide for a detailed description of the shared responsibilities of the
customer and of Xerox.
Client workstations and system software
To send print jobs to the DocuPrint NPS printer, the customer needs
to provide the proper client hardware as well as operating system
and network software.
Supported hardware and operating systems
Xerox DocuPrint Model 92C NPS supports the following types of
networked client workstations and operating systems:
•Sun Workstation running Solaris 1.1.x or Solaris 2.x
•PC running MS-DOS 6.2 and Microsoft Windows 3.1, using
Ethernet with TCP/IP or Novell NetWare 3.11 and 3.12
Note: Customers using Novell 4.1 must set the “Bindery
Emulation Mode”to be backwards compatible with Novell
3.12.

PRODUCT OVERVIEW
1-4 XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
•PC 386 or 486, running MS-DOS, version 6.2, with one of the
following TCP/IP packages:
—PathWay Access 3.1, Wollongong Integrated Networking/
Transmission Control Protocol (WIN/TCP) for DOS, release
6.0
—File Transfer Program (FTP) software, PC-TCP/IP, release
3.0 or higher
—Sun Personal Computer–Network File Services (PC-NFS),
version 5.1
•IBM RS/6000 running IBM AIX, version 4.1
•HP/Apollo running HP-UX, version 10.01
•DECStation 5000/200 running DEC Ultrix, version 4.3
•Apple Macintosh, System 7.x or 8.x, using AppleTalk through
EtherTalk, phase 1 or 2
•Any system that supports RFC-1179 lpr/lpd.
DocuPrint Model 92C NPS software may be compatible with
workstation models and software versions other than those listed
above.
Client networking software
Xerox client software, a third-party TCP/IP lpr networking software,
Novell, or Apple/Macintosh Printer Access Protocol (PAP)
networking software must be installed on your client workstations or
downloaded from the printer controller. This software provides an
interface with the printer controller, which allows you to submit print
jobs and check job status.
Note: The DocuPrint printing options available to a client user vary
according to the networking software loaded on the client
workstation.
For additional information on submitting jobs from a client
workstation, refer to the Xerox DocuPrint Network Printer Series
Guide to Submitting Jobs from the Client.
Ethernet LAN
Users of networked client workstations may send print jobs to the
DocuPrint NPS printer over the Ethernet LAN using TCP/IP,
AppleTalk using EtherTalk Link Access Protocol (ELAP), or Novell
NetWare 3.1x as the network protocol.
Regardless of printing or transmission protocol, the Ethernet
connection to the printer controller must be compatible with the
Institute of Electrical and Electronics Engineers (IEEE) 802.3
standard.

PRODUCT OVERVIEW
XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS 1-5
Token Ring
Users of network client workstations may send print jobs to the
DocuPrint NPS printer over Token Ring network using TCP/IP,
Novell 3.x, or AppleTalk network protocol.
Regardless of printing transmission protocol, the Token Ring
connection to the printer controller must be compatible with the
Institute of Electrical and Electronics Engineers (IEEE) 802.5
standard.
Fiber Distributed Data Interface
TCP/IP, Novell 3.x, and Apple Talk network protocols are supported
over FDDI. The FDDI supports a Single Connection configuration
only.
NPS/IPS Dual Mode
The Xerox DocuPrint Dual Mode option enables both DocuPrint IPS
and NPS systems to coexist on the same printer controller (Sun
workstation). This allows the DocuPrint system to receive data
streams supported by NPS and IPS, including IPDS, PostScript
Levels 1 and 2, HP PCL5c, HP PCL5e, and ASCII.
The customer may switch from one mode to the other. When your
system is operating in IPS mode, it can accept PostScript and PCL
data streams in the background; however, you can print these jobs
only when the system is in NPS mode. When in NPS mode, the
system cannot accept IPDS data streams in the background; you can
print them only when the system is in IPS mode.
Refer to the Xerox DocuPrint IPS/NPS Dual Mode Switching
Instructions and other Xerox DocuPrint IPS documentation for more
information.
Sixth Sense
Sixth Sense is a unique suite of diagnostic tools that allows Xerox
customer service engineers, analysts, and consultants to serve
customers more effectively.
Sixth Sense is intended to automate and expedite the range of
service-related support functions. Sixth Sense is a tool that enables
Xerox to provide benchmark service support. Xerox customers
benefit from the ability to bring broader support to focus more quickly.
For example, Sixth Sense can allow the Service Representative to
repeatedly "preview" the condition of the system prior to an actual
site visit. This may provide the ability to determine the correct part or
piece of information to have on hand when the site visit is made.
Sixth Sense is a no charge feature available to customers through
Xerox Service. The customer need only provide an analog phone line
for use by the Sixth Sense modem connection. For those customers
unable to dedicate a phone line to the Sixth Sense connection, three
and five port phone share devices are available for purchase.

PRODUCT OVERVIEW
1-6 XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
To take advantage of Sixth Sense, the customer needs to:
•Request Sixth Sense enablement through Xerox Service
•Provide an analog phone line
•If necessary, purchase an optional phone share device.
More information about the Sixth Sense can be found in the Xerox
DocuPrint 4850/4890 NPS System Administration Guide.

XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS 2-1
2. 2Controller components and
options
The printer controller provides the printer with print data and
commands, and receives status information from the printer. This
chapter describes the components and options available for the
controller.
Controller hardware
The printer controller consists of a Sun workstation and uses
proprietary Xerox hardware, firmware, and software to run the NPS.
Your controller may be either a Sun Ultra 2 or Ultra 60 workstation.
The following sections contain information about both the Ultra 2 and
the Ultra 60.
Sun Ultra 2 workstation
The Sun workstation provides a user interface to the print engine. It
is used to operate the NPS software that controls the printer. The
workstation contains the following hardware components:
•Sun Ultra 2 workstation processor (system unit)
•Display monitor
•Keyboard and mouse
•Connectivity boards for Ethernet and, optionally, Token Ring
•A Data Control Interface Module (DCIM2) card installed in the
processor to interface with the print engine.

CONTROLLER COMPONENTS AND OPTIONS
2-2 XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
Figure 2-1. Components of the Sun Ultra 2 workstation
1 Processor
2 Monitor
3 Mouse and mouse pad
4 Keyboard
5 Diskette drive
6 CD-ROM drive
Processor The 256 MB RAM processor is the central processing unit of the Sun
workstation. It contains a power switch, an internal disk drive, a
diskette drive, a CD-ROM drive, a power receptacle and outlet,
connectors and ports.
The processor has the following components:
•Internal disk drive: One 4.2 GB internal disk drive is provided
as a standard feature of the processor. The operating system,
the NPS application, and any queued print jobs are stored on
the internal disk. This disk cannot be used to store other
applications or data except as directed by your service
representative. Up to three optional disk drives are available in
increments of 4 or 9 GB.
•Diskette drive: Diskettes inserted into a diskette drive are used
to load files to, and back up files from, the internal disk drive.
The diskette drive uses industry standard 3.5 inch, 1.44 MB,
double-sided, high-density diskettes. This diskette drive is not
an input source for print jobs nor any other data or application; it
is reserved exclusively for use by a service representative to
update software and to store files. The diskette drive is located
in the processor, on the right front section for the Ultra 2.
1
3
4
2
6
5

CONTROLLER COMPONENTS AND OPTIONS
XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS 2-3
•CD-ROM drive: The CD-ROM drive is a high density, read-only,
optical laser storage device used for loading the NPS operating
system and other files. The CD-ROM drive is located in the
processor above the diskette drive.
•Cartridge tape drive (not shown): An optional 8 GB, 4 mm
SCSI cartridge tape drive also is available for the NPS. Like the
diskette and CD drives, this tape drive is not an input source for
print jobs or for any other data or application. It provides the
service representative with another means of loading system
maintenance files or saving diagnostic information.
•Back panel: The back panel of the processor has a power
switch, a power receptacle and outlet, connectors, connector
openings, and ports. The following figure shows the back panel
of the Sun workstation that is a part of your NPS controller.
Figure 2-2. Back panel of the Sun Ultra 2 processor
1 Power inlet
2 Serial connectors (2): RS-432/RS-232
3 Graphics/video output: UPA slot
4 Sbus slots (Number of slots varies depending on the model)
5 Audio connectors (4)
6 Parallel connector
7 Keyboard/mouse connector
8 TPE connector
9 MII connector
10 UPA slot
11 SCSI connector
12 Power on/Standby switch
Display monitor The display monitor has a 1192 x 700 pixel screen which displays the
NPS graphical user interface windows.
The graphical user interface allows you to interact with the printer
and to monitor its interaction with the various components. During a
print job, printer error messages may display to notify you of any
unexpected conditions.
11 98765
12
1234
10
3
20
1

CONTROLLER COMPONENTS AND OPTIONS
2-4 XEROX DOCUPRINT NETWORK PRINTER SERIES INSTALLATION PLANNING GUIDE FOR MODEL 92C NPS
Keyboard The keyboard consists of alphanumeric keys similar to a typewriter,
symbols and special character keys, an extended character set, and
function keys. The keyboard is one of your main methods of
communicating with the printer. You can use the keyboard to make
selections, and to enter commands that control functions such as
requesting sample prints, obtaining billing meter totals, shutting down
the system, and so forth.
Mouse The mouse is another main method of communicating with the
printer. The mouse has three buttons. The left and right buttons are
used to select NPS functions. The center button provides additional
functions that you will not be required to use. If your workstation has
an optical mouse, it must remain on its designated metallic pad to be
active. If the mouse has a roller ball instead of an optical sensor
underneath, it requires a non-metallic pad.
Note: Printer controller hardware configurations are subject to
upgrade.
Sun Ultra 60 workstation
The Sun Ultra 60 workstation provides a user interface to the print
engine. It has a high performance RISC processor chipset, based on
the industry standard Scalable Processor Architecture (SPARC). It is
used to operate the software that controls the printer. The
workstation contains the following hardware components:
•Sun Ultra 60 workstation processor (system unit)
•Display monitor
•Keyboard and mouse
•Diskette, CD-ROM, and cartridge tape drives
•Connectivity board for Ethernet and, optionally, Token Ring
•A Data Control Interface Module (PDCIMu) card installed in the
processor to interface with the print engine.