Xerox Nuvera 100 Assembly instructions

Software Version 10.2
21 May 2010
701P50711
Xerox Nuvera®
Hints and Tips Guide
Xerox Nuvera 100/120/144 EA/MX Production System
Xerox Nuvera 200/288 EA/MX Perfecting Production System

©2010 Xerox Corporation. All rights reserved. XEROX® and XEROX and Design®, Xerox Nuvera® and FreeFlow® are
trademarks of Xerox Corporation in the United States and/or other countries.
Changes are periodically made to this document. Technical inaccuracies and typographic errors will be corrected in
subsequent editions.
Document Version: 10.2 (May 21, 2010).

Table of Contents
Preface....................................................................................................................... v
.......................................................................................................vGeneral Purpose and Audience
1Software Versions....................................................................................1-1
2New Capabilities in Version 10.2 Software....................................2-1
3Release Issues ...........................................................................................3-1
...................................................................................................................................3-1Issues resolved
................................................................................3-2Issues remaining from previous release
............................3-2CQ#45919 Tray Programming Reverts to Default Settings
...........................................................................................................3-2CQ#45544 Build Job
............................................3-2CQ#43471 Skewed Inserts with Xerox Tape Binder
..................................................................................................3-2CQ#43522 Annotation-1
..................................................................................................3-3CQ#43522 Annotation-2
................................................................................3-3CQ#44256 Configuration Backup
................................................3-3CQ#44223 PDF and HTML Files Viewed from CD
..................3-3CQ#44186 Recognizing Indication of Successfully Proofed Job
...................................................................3-4CQ#38117 Short Edge Feed 9x11 Stock
CQ#26871 Queue and Job based subsetting fails for Odd number of
pages duplex jobs ................................................................................................................3-4
CQ#47602 DS3500 finisher: a Job integrity issue may occur if the unload
button is pressed just before the first sheet is delivered...................................3-4
................................................3-4CQ#47579 Non-clearable Top Edge Sensor Fault
CQ#46849 Message stating 'The online configuration file online.config
does not exist' when closing the 'Gateways'.........................................................3-5
3-5CQ#47518 When printing files from CD, all pending jobs go to reject state
CQ#47650 Printer will boot up slowly when FFRPS is on and the user has a
firewall turned on.................................................................................................................3-5
3-5CQ#46415 System may stop at SUNOS banner screen during power on
...................3-6When exiting MICR Mode, the Edge erase remains at no erase
Hints and Tips Guide iii

Preface
General Purpose and Audience
This document for the Xerox Nuvera contains the following information:
•Software release deliverables and version numbers
•New features in this release
•Issues resolved in this release
•New issues present in this release
•Known operating limitations that are to be resolved in a future release
Standard system operating procedures and information can be found in the following
documentation:
•For specific information about system operations, performance and features, refer to the
Xerox Nuvera User Guide and Training Aid.
•For connectivity topics and DFA configuration management, refer to the Xerox Nuvera
System Administrator’s Guide as well as the DFA Resource Guide.
•For print driver installation, supported print drivers, and common issues with the Xerox
FreeFlow® Print Server print driver functionality, refer to the CentreWare Printer Drivers
Guide. New print drivers are available at www.xerox.com.
•For LCDS specific information, refer to the LCDS User Guide.
•For more detail on IPDS functionality refer to the FreeFlow Print Server IPDS User Guide.
Hints and Tips Guide v

Preface Xerox Nuvera
[This page left intentionally blank]
vi Hints and Tips Guide

1
1Software Versions
This document references the following software versions:
Item Version Number
Free Flow Print Server 7.0 SP3 / Tigris
System software
RV.9.2.24.xx
CP.73.A1.31
IPDS (must match DocuSP version) CP.73A1.31
FreeFlow Print Server 7.0 SP3 Remote
Workflow *
CP. 73A1.14 (English)
CP. 73A1.14 (Multinational)
FreeFlow Print Server 7.0 SP3 and
Variable Input version
FreeFlow Print Server 7.0 SP1 Includes Variable Input
(VI) and Variable Print Manager (VPM) version 5.0.
VIPP Version VIPP Project Container is known as the FreeFlow VI
Project Container.
Drivers ** 100/120/144/200/288 EA/MX DPS
CD Release version: 02.073.09
Windows Driver: 5.138.3.0
Mac Driver: 7.0.6 (497)
FreeFlow Print Server 7.0 SP1 x86
System Restore
CP.5162.93 01-July-2007
* Note
Since the Xerox software supports the current release and two past major releases,
DocuSP Remote Workflow 5.1 software supports DocuSP versions 4.1, 4.2, 5.0, and 5.1. If
an earlier version of DocuSP is being used, you can install an older version of DocuSP
Remote Workflow. DocuSP Remote Workflow 5.0 software supports DocuSP versions 4.1,
4.2 and 5.0. Version 3.8 software will no longer be visible to the 5.0 DRW software.
Alternatively, you can run two applications on the desktop.
** Note
The print drivers included with the system support Microsoft Windows Vista. Check the
driver download page at www.xerox.com for print driver documentation.
Hints and Tips Guide 1-1

2
2New Capabilities in
Version 10.2
Software
The following is a list of new capabilities enabled with version 10.2 software:
1. The Xerox Tape Binder (XTB) is now configurable in Dual Mode (2 XTB’s connected
together).
2. Disable status messages when trays are disabled. This de-clutters the status message area
when a tray is disabled.
3. Add a custom edge erase feature that can set the edge erase in the range of 0 mm to 6
mm for each of the four edges.
4. Added the ability to disable/enable a stacker (on DS3500 or BFM). This allows the user to
disable a stacker if they want to restrict jobs from going to that stacker and then re-enable
later.
5. Enable both top trays for purge events on systems with 2 top trays. This will improve
purge effectiveness.
6. Improved jam clearance by adding additional areas that can be purged to the 5B area.
7. Added several new Finisher profiles to the catalog.
Hints and Tips Guide 2-1

3
3Release Issues
Issues resolved
The following is a list of Nuvera 10.1 issues that have been resolved and no longer apply to
Xerox Nuvera 10.2 systems:
•CQ#43933 Unable to Eject CD Tray
•CQ#45892 MICR Mode does not disable Edge Treatment
Hints and Tips Guide 3-1

Release Issues Xerox Nuvera
Issues remaining from previous release
CQ#45919 Tray Programming Reverts to Default Settings
Description
When 'After Every Tray Cycle' tray confirmation is enabled, and a tray is cycled, all tray
programming, except for Stock Size, in the pop-up confirmation window is set to default.
Workaround
If you are using named stock or stock weight different than the queue default weight then it is
recommended that you set [System Preferences -> Stocks and Trays -> Tray Confirmation] to
‘None’. If you do not, then each time the tray confirmation pop-up window opens all the
values will be set to the queue default values.
CQ#45544 Build Job
Description
11x17 and 8 1/2x14 build jobs are printing with second segment as 8.5x11 instead of 11x17.
Workaround
When using Build Job, please leave the paper selection set to APS before entering Build Job.
Once you are in Build Job you can change the paper selection to any stock you wish. You also
can leave it set to APS.
CQ#43471 Skewed Inserts with Xerox Tape Binder
Description
Books printed on 60gsm paper that have heavy (90gsm and higher) inserts can cause last
several pages in the book to be skewed.
Workaround
Recommend using inserts less than 90gsm when body is 60gsm.
CQ#43522 Annotation-1
Description
Do not use Annotation when feeding from the short edge feed tray and selecting the 180
degree rotate. The annotation will be upside-down.
Workaround
None.
3-2 Hints and Tips Guide

Xerox Nuvera Release Issues
CQ#43522 Annotation-2
Description
When performing a “Copy and Save” or “Print and Save” operation with annotations turned
on, the reprint of the saved job will be unreadable.
Workaround
Perform a “Save” operation and then “Print” the saved job.
CQ#44256 Configuration Backup
Description
When performing a Configuration Backup, make sure you do not exceed the maximum disk
size of the CD. If you do, the backup will fail without an indication as to why.
Workaround
None.
CQ#44223 PDF and HTML Files Viewed from CD
Description
Operator needs to view PDF or HTML files on a CD.
Workaround
Do one of the following:
1. To view PDF files, go to [Launch -> Applications -> Graphics -> PDF Document Viewer]
and open the PDF on the CD.
2. To view HTML files, go to [System -> Remote Services -> Options -> Launch Web
Browser].
CQ#44186 Recognizing Indication of Successfully Proofed Job
Description
When a job is successfully proofed, there appears to be no indication that it has been proofed.
Workaround
Ensure the “Proof/Review Status” column is in the visible portion of the table. This column is
identified by a computer icon in the header. If the column is at the end of the table (left side),
move it to the beginning (right side). A successfully proofed job will have an icon appear in this
column that looks like a green check mark over a document.
Hints and Tips Guide 3-3

Release Issues Xerox Nuvera
CQ#38117 Short Edge Feed 9x11 Stock
Description
9 x 11 stock cannot be loaded short edge first (SEF).
Workaround
Load an SEF-only stock such as Legal, run one or more sheets on that stock, then unload it and
put in 9x11 S
CQ#26871 Queue and Job based subsetting fails for Odd
number of pages duplex jobs
Description
Subset offset and finishing can be programmed on job in the job manager or on a Queue. This
works fine for simplex jobs. It will also work for duplex jobs as long as the request is for an
even number of images. But if the request is for a subset that would require a duplex page to
be split then the request fails.
Workaround
Only program even number of pages in the subset.
CQ#47602 DS3500 finisher: a Job integrity issue may occur if
the unload button is pressed just before the first sheet is
delivered
Description
IF the user presses the DS3500 stacker unload button just before the first sheet of the job
reaches the stacker, there may be a jam in the flipping wheel area which could cause job
integrity issues.
Workaround
Please do not press the DS3500 stacker unload button just before receiving the first sheet of a
job
CQ#47579 Non-clearable Top Edge Sensor Fault
Description
If a Top Edge Sensor fault occurs and the machine is restarted with the IOT doors open, a non-
clearable Top Edge Sensor Fault may occur.
Workaround
Close the IOT doors and then Power-off/Power-on the machine and the fault will clear. To
avoid the occurrence, ensure the IOT doors are closed before restarting the machine.
3-4 Hints and Tips Guide

Xerox Nuvera Release Issues
CQ#46849 Message stating 'The online configuration file
online.config does not exist' when closing the 'Gateways'
Description
The above error message may occur when closing the “Gateways” window in the Online Setup
tab.
Workaround
If this occurs, select OK in the error message and then close or Cancel in the gateways window.
CQ#47518 When printing files from CD, all pending jobs go to
reject state
Description
When printing files from the CD and the user selects the eject button will cause all pending
jobs to change to reject state.
Workaround
Do not eject the CD while printing files for the CD. If all this was done, all jobs will need to be
resubmitted.
CQ#47650 Printer will boot up slowly when FFRPS is on and the
user has a firewall turned on
Description
When the user has FreeFlow Remote Printing Service turned on and a firewall turned on, the
printer will take longer than usual to restart or power on.
Workaround
Turn off FFRPS or the firewall before starting up or restarting the printer.
CQ#46415 System may stop at SUNOS banner screen during
power on
Description
After powering on the printer, the system may stop at a black screen with the “SUNOS 5.10
Version …” banner message.
Workaround
Power off and then back on to correct the problem.
Hints and Tips Guide 3-5

Release Issues Xerox Nuvera
When exiting MICR Mode, the Edge erase remains at no erase
Description
When exiting MICR Mode, the edge erase setting will remain at “none”. We leave it to the user
to set the edge erase to the values they want.
Workaround
Do not forget to set the edge erase to desired setting after exiting MICR Mode.
3-6 Hints and Tips Guide