Xerox Phaser 6200 User manual

Phaser®6200 Color Laser Printer
Copyright © 2002 Xerox Corporation. All Rights Reserved. 2
Trays
This section covers:
■Loading paper in Trays 1-3 —see page 2.
■Loading paper in the Multi-Purpose Tray —see page 6.
■Using custom size paper —see page 8.
For a list of the acceptable papers, transparencies, envelopes, and labels that can be used in each tray,
refer to the Supported Papers section of the Trays and Paper Guide on the Interactive Documentation
CD-ROM.
Note
Do not load a tray that is currently being used for printing.
You MUST set the paper type in the printer’s front panel any time you add paper to the printer. If you
change paper types, take a moment to ensure that the front panel values agree with the paper you have
loaded. If you fail to do this, you can damage the printer’s fuser.
Loading paper in Trays 1-3
Caution
Phaser®6200 Transparency film is designed specifically to work with this printer's oil-less
fuser. Using non-Phaser 6200 Transparencies might result in poor image quality and might
damage the fuser. Damage caused by using non-Phaser 6200 Transparencies is not covered
under the warranty, service agreement, or Total Satisfaction Guarantee. To order
Phaser®6200 Transparencies, visit the Phaser®6200 Supplies and Accessories web site.
DO NOT load Phaser®6200 Transparency Film in Trays 2 or 3; use Tray 1 or the
Multi-Purpose Tray instead.
Caution
DO NOT load card stock, glossy coated paper, photo paper, envelopes, labels, business
cards, greeting cards, CD/DVD labels, and CD/DVD inserts in Trays 1-3; use the
Multi-Purpose Tray instead.
To load paper in Trays 1-3:
Instructional videos for loading trays are available on the Interactive Documentation
CD-ROM or the Xerox web site at: www.xerox.com/officeprinting/6200support/
You can also refer to the labels inside the printer for paper loading instructions.
Note
If you change the type of paper, you MUST
specify the type on the front panel of the printer.
OK
6200-46

Trays
Phaser®6200 Color Laser Printer 3
1. Pull out the tray.
2. If loading paper having a different width, push the width guides outward. If loading paper having a
different length, tilt the back guide forward, slide the guide, and insert the pins on the bottom of
the guide into the holes in the tray corresponding to the paper size you are loading.
3. Fan the paper to release sheets that are stuck together.
6200-35
6200-01

Trays
Phaser®6200 Color Laser Printer 4
4. Insert a stack of paper into the tray. Place the paper under the front corner tabs and under the tabs
on the back guide. For one-sided prints, place the side to be printed faceup with the top of the page
at the front of the tray. For two-sided prints, place the side to be printed with the odd-numbered
pages facedown with the top of the page at the back of the tray. If using paper with pre-punched
holes, place the holes toward the right side of the tray.
Note
Observe the fill lines on the side of the tray. Do not load paper above the paper fill line (1),
because it may cause a jam. Do not load transparencies above the transparency fill line (2).
5. If necessary, push the width guides inward to match the size of the paper.
MAX
6200-03
1
2
MAX
6200-04

Trays
Phaser®6200 Color Laser Printer 5
6. Insert the tray and push it completely into the printer.
7. When the front panel prompts you:
■If you haven’t changed the type of paper, press the OK key to accept the current setting for
paper type.
■If you have changed the type of paper, scroll to the correct paper type and press the OK key
to save your selection.
Note
To avoid possible print-quality and paper-feed problems, make sure that the tray’s paper type
setting matches the loaded paper type.
6200-36
OK
6200-45

Trays
Phaser®6200 Color Laser Printer 6
Loading paper in the Multi-Purpose Tray
Use the Multi-Purpose Tray for envelopes, transparencies, custom size paper, and specialty papers, such
as labels, business cards, greeting cards, CD/DVD labels, and CD/DVD inserts as well as paper.
Caution
Phaser®6200 Transparency film is designed specifically to work with this printer's oil-less
fuser. Using non-Phaser 6200 Transparencies might result in poor image quality and might
damage the fuser. Damage caused by using non-Phaser 6200 Transparencies is not covered
under the warranty, service agreement, or Total Satisfaction Guarantee. To order
Phaser®6200 Transparencies, visit the Phaser®6200 Supplies and Accessories web site.
DO NOT load Phaser®6200 Transparency Film in Trays 2 or 3; use Tray 1 or the Multi-
Purpose Tray instead.
Note
Automatic 2-sided printing is not available from the Multi-Purpose Tray.
To load paper in the Multi-Purpose Tray:
1. Open the Multi-Purpose Tray (labeled MPT) by pushing the handle down and out.
Note
If you change the type or size of paper, you
MUST specify the type and size on the front
panel of the printer.
OK
6200-46
6200-06

Trays
Phaser®6200 Color Laser Printer 7
2. Adjust the width guides to match the size of the paper.
3. Insert the paper, transparencies, or envelopes in the Multi-Purpose Tray. Load the side to be
printed facedown with the top of the page entering the printer first. Do not load paper above the
fill line. Place envelopes with the flap side up and top of the envelope towards the right of the
printer. (For A7 envelopes, place the flap side up but have the top of the envelope enter the printer
first.)
4. When the front panel prompts you and you haven’t changed the type or size of paper, press the
OK key to accept the current settings for type and size.
6200-07
6200-08
6200-10

Trays
Phaser®6200 Color Laser Printer 8
5. If you have changed the type or size of paper:
a. On the printer’s front panel, scroll to Change by pressing the Down Arrow key, then press
the OK key.
b. Scroll to the correct paper type and press the OK key to save your selection.
c. Scroll to the correct paper size and press the OK key to save your selection.
Note
To avoid possible print-quality and paper-feed problems, make sure that the tray’s paper type
and size settings match the loaded paper type.
Using custom size paper
In addition to the wide variety of standard paper sizes available for this printer, you can use custom size
paper in the Multi-Purpose Tray.
Loading custom size paper in the Multi-Purpose Tray
1. Open the Multi-Purpose Tray, as described on page 6.
2. Insert the custom size paper and adjust the guides to match the size of the paper. Place the side to
be printed facedown with the top of the page entering the printer first.
Size Range
X dimension 89 mm - 216 mm
3.5 in. - 8.5 in.
Y dimension 140 mm - 356 mm
5.5 in. - 14 in.
OK
6200-45
6200-57
1
2

Trays
Phaser®6200 Color Laser Printer 9
3. When the front panel prompts you to confirm the type and size of paper:
a. Scroll to Change (by pressing the Down Arrow key) and press the OK key.
b. Scroll to the correct paper type and press the OK key to save your selection.
c. For the paper size, scroll to Custom and press the OK key.
d. Select Set Custom X by pressing the OK key.
e. Press the Down Arrow or Up Arrow key to scroll to the desired value for X(labeled 2in the
illustration in Step 2) and then press the OK key.
f. Scroll to Set Custom Y and press the OK key.
g. Press the Down Arrow or Up Arrow key to scroll to the desired value for Y (labeled 1in the
illustration in Step 2) and then press the OK key.