XL Systems 0001908 User manual

XL Systems Inc
14 Dora Ln Holmdel, NJ 07733
HO Steam Sound Only Decoder
Item #0001908
Thank you for purchasing our advanced DCC diesel 16 bit sound only
decoder. Combined with any non-sound power decoder installed in your
locomotive, and used with your favorite DCC System, our new sound only
decoder will make your model locomotive come to life.
! Easy installation - two wire only
! 20 types of synchronized chuff (10 single and 10 double) with
random associated locomotive sounds
! 28 functions (F1 - F28)
! 2 or 4-digit (1-9999) addressing
! Programmable 14, 28, 128 speed steps
! Programmable acceleration rate, deceleration rate
! Programmable user selectable 17 whistles and 7 bells
! Programmable individual sound volumes (64-levels)
! Programmable master sound volumes (64-levels)
! Supports advanced consisting (CV19)
! Supports programming on the main(OPS mode)
! Compatible with NMRADCC standards
! Complies with the part 15 of FCC
! Speakerincluded
! Dimensions: 17.4mm x 17.4mm x 4.0mm
INSTALLATION
Since there is no motor output in this sound decoder, it can be used in any locomotive, regardless
of scale that already has a working power decoder installed. If used in large scales where
track voltage exceeds 16 volts, (O/G scales), a special voltage reducer is required to be used
in-line to the Sounder. Contact Model Rectifier Corp. for details and price. To install the Sounder into
a locomotive, simply solder the red and black wires to any power pick up points, left and right side
wheel pick ups, along with the red and black wires of your power decoder. If using with higher
voltage DCC applications for larger scales, solder the MRC voltage reducer to either the red or black
wire between the Sounder, and the power pick up point. You should have some basic electrical
knowledge and soldering skills. If you do not have the above requirements, please ask the dealer
for help with the installation.
Note- Instead of using CV3 and CV4, the decoder uses CV120 and CV121 as acceleration and
deceleration rates. So you can change its acceleration and deceleration rates without changing CV3
or CV4 in your power decoder, if you already have these rates tailored for your locomotives optimum
performance.
SPEAKER SELECTION
The “XL Sounder” steam sound only decoder comes with a 28mm round 8-ohm speaker. If it is
too large for your application, smaller speakers, 20mm, or 16 X 35mm rectangular, can be
purchased from XL, or other manufacturers. Reducing speaker size will affect the overall
sound quality of this decoder. Placement of the speaker inside the locomotive is up to you. Use
hot glue or double-sided sticky tape to affix the speaker inside the locomotive shell.
TROUBLE SHOOTING:
This decoder should perform well with all DCC systems. The maximum DCC output should
be less than 15 V. If the locomotive does not respond to commands, it may have lost its
address. Please reprogram the address and program CV19 to 0 (disable consist). If it
responds slowly, you should clear its momentum by reprogramming CV120 and CV121 to
zero. You should also clean the track to improve electrical pickup. Read your DCC system
manual to learn how to program and operate the decoder. Whenever the decoder doesn’t
work please use the program track to program CV# 125 with value 1 to restore the decoder
to factory settings. This should bring the decoder to life with address #3.
RETURN PROCEDURE:
This decoder carries a 6 month warranty against factory defects. This warranty does not
include abuse, misuse, neglect, improper installation, or any modifications made to this
decoder. If it should become necessary to return the decoder for warranty repair/
replacement, please include a copy of the original sales receipt. Please include a letter
(printed clearly) with your name, address, daytime phone number, and a detailed
description of the problem you are experiencing. Please also include a check or a money
order for $8.00 to cover return shipping and handling. If the decoder is no longer
considered under warranty, then please include a check or a money order for $12.00 to
cover the cost of repair or replacement and return shipping and handling.
Send the decoder to:
XL Systems Inc
14 Dora Ln
Holmdel, NJ 07733
Email: [email protected]
ADDRESS PROGRAMMING:
The “Sounder” comes with a factory default address of #3, and 28 speed steps. If your
locomotive has a different address, and speed step already programmed into it, place the
locomotive, with decoder and Sounder installed, on your program track and reprogram it to
the address you had originally programmed it to. While it is on the program track, also
reprogram the locomotive to the speed step of your choice, (14-28/128). Since the decoder
does not have a motor driver, you can’t read back its CV.
ADDITIONAL INFORMATION:
The Sounder synchronized steam chuff sound only decoder should perform well when
used with other brand command systems, and decoders. See your DCC command stations
manual to learn how to program and operate any decoder. For more information about
register/CVs and their functions, please refer to the NMRA DCC Standard &
Recommended practices, RP-9.2.2 available directly from the NMRA or their website at
www.nmra.org.
OPERATION
There are 17 whistles sounds and 7 bell sounds, along with an “off” setting for each built into this
decoder for you to choose from. See programming chart for selecting the type you want. The “off”
setting is useful for trailing locomotives in a consist so only the lead unit sounds its whistle and bell.
You can use F18 functions to change the type of bell sound, and use F19 to select horn sound,
Note: If you activate the bell sound, F1, while either the Rail-Wheel Clack
sounds are activated, the Bell sound will override the other two sounds.

CV CHARTER
CV CHARTER
CV Description Range Default
CV1 Short address 1-127 3
CV29 Basic configuration 2
CV7 Manufacturer version number 32
CV8 Manufacturer ID 143
CV17 Long address upper byte 192-231 192
CV18 Long address lower byte 0-255 3
CV19 Advanced consist address 0-127 0
CV21 When CV21=0, all accessory function will follow its own address. When CV21=1, all
functions will follow the consist address 0-1 0
CV49 Master volume control 0-63 63
CV50 Whistle type 0-13 5
CV51 Whistle volume 0-63 55
CV52 Bell type 0-3 0
CV53 Bell volume 0-63 55
CV54 Bell ring rate 0-50 10
CV55 Chuff type 0-10 0
CV56 Chuff volume 0-63 55
CV57 Brake squeal volume 0-63 55
CV58 Air release volume 0-63 55
CV59 Blower hiss volume 0-63 55
CV60 Fire box door volume 0-63 55
CV61 Injector volume 0-63 55
CV62 Coupling volume 0-63 55
CV63 Air pump volume 0-63 55
CV112 metal crank volume 0-63 55
CV115 Auto brake squeal enable/disable 0-1 1(enable)
CV116 Sand drop volume 0-63 55
CV117 chuff rate
CV118 Shoveling volume 0-3 0
CV119 Coal volume
CV120 Acceleration 0-255 255
CV121 Deceleration 0-255 255
CV122 Double chuff enable 0-1 0
CV123 Safty valve type 0-2 0
CV122 Chuff start point 0-7 0
CV125 Program it to1 will restore some the CV to factory default settng 0
Item #0001908
FUNCTION CHARTER:
F1 Bell on/off
F2 Whistle
F3 Air release
F4 Coupling 1
F5 Brake release / brake squeal
F6 Chuff sound on/off-all other soundson
F7 Air hose firing/uncoupling lever
F8 Water injector
F9 Metal crank soundon/off(moving), steam associated sound(idle)
F10 Water filling
F11 Blow er hiss
F12 All sounds on/off
F13 Master volume reduce by 1 / air release
F14 Master volume increase by 1 / air release
F15 Flangenoise
F16 Shoveling
F17 Coalauger
F18 Change bell type (8 types plus off)
F19 Whistle type select (total 17 different horns)
F20 Airhose firing/uncoupling lever
F21 Flangenoise
F22 Associated loco sound
F23 Flangenoise
F24 Chuff type select
F25 Longair release
F26 Sanddroppin
F27 Associated loco soun
F28 Associated loco soun
Function Idel/Moving
About XL SYSTEMS INC xlsystemsdcc.com
XL Systems Inc has designed and manufactured model rail road products for MRC for more than 20
years. All MRC DCC products are made by XL Systems Inc. Now we promote our own brand. We
will provide the best value and service to our customer. All our DCC decoders are compatible NMRA
DCC standard. We will introduce more new products to meet customer’s needs and beget. We also
provide installation and special programming for customer. Please visit our website at
xlsystemsdcc.com for more product information. If you have special needs please contact to us
at [email protected]
XL SYSTEMS INC 14 Dora lane Holmdel, NJ 07733. Web: xlsystemsdcc.com