Xpresskit DBALL2-HYUNDAI9 User manual

Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Vehicle Application Guide...................................................................................................................................................
Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)
Type 1.................................................................................................................................................................................
Type 2.................................................................................................................................................................................
Programming
Module Programming.........................................................................................................................................................
Module Reset.....................................................................................................................................................................
Hard Reset.........................................................................................................................................................................
Feature & Option List..........................................................................................................................................................
Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Limited One-Year Consumer Warranty...............................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
03
05
07
08
08
09
09
10
12
13
Index
® Hyundai is a registered trademark and property of its respective company.
Note: This firmware does not support pitstop/idle mode.
The HYUNDAI9 firmware for DBALL2 is an all-in-one door lock and override module compatible with
specific Hyundai vehicles.
This module can only be flashed and configured using XpressVIP at www.directechs.com or
using the Directechs Mobile application for smartphones. Refer to the Module Programming
section on page 5 for more information.
Rev.: 20170512
Platform: DBALL2
Firmware: HYUNDAI9
© 2017 Directed. All rights reserved.

Vehicle Application Guide Page 2
Vehicles
2017 2016 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-RAP Shut Down (Retained ACC Power) RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status ST-Ignition Status
Hyundai
Tucson (Smart Key) 2 1 • • • • • • • • D • • • • • D • D • •
Legend:
PK: Transponder & Immobilizer Override
AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
The following table lists the vehicles and features which are compatible with this product. The number assigned to each
year allows you to determine which installation type should be used for your vehicle.
Rev.: 20170512
Platform: DBALL2
Firmware: HYUNDAI9
© 2017 Directed. All rights reserved.

Remote
Starter
(-) GWR (Status)
(-) Ground (-) Ground
(-) Lock Output
(-) Unlock Output
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
(-) Trunk Output
FT CAN High: Orange/Green: 5
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 3
FT CAN Low: Orange/Brown: 6
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status Output: Blue/Red: 12
E-Brake Status Output: Black/White: 1
(-) E-Brake Status Input
(-) Door Status
(-) Trunk Status
(AC) Tach Input
(+) Brake Status
(-) Hood Status
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
(AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
Diagnostic
Connector
OBDII
1 8
169
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
(MUX) Parking Lights Output: Violet/Brown: 9
7 Pink/White: (-) Parking Lights Input
(-) Parking Lights Output
(+) Accessory Output
(+) Starter Output
Ign. Interrupt (conn. side): Orange/Red: 10
Ign. Interrupt (veh.side): Yellow/Red: 11
EMS COM: Orange/Black: 11
(-) Ignition Status Output
Smart Key Ign. Interrupt: Green, pin 6
I/P-F Fusebox/Smart
Junction Box
(White conn. rear of
fusebox/Smart Junction Box)
B-CAN High:
Green/Black, pin 3
(+) Starter:
Red/Black,
pin 31
EMS COM: Blue, pin 20
MC11 Junction
(Gray conn. at
driver kick panel)
10
37 29 22 18
11
38 30 23 19
12
39 31 20
1721
36 28
1
2
3
4
5
6
7
8
9
13
14
15
16
4
5
6
7
32
33
34
35
40
41
42
43
44
45
46
47
48
CUT
(MUX) Parking Lights:
Yellow, pin 14
Headlight/Wiper Switch
(Black conn. at steering column)
1 3 5 72 4 68
9 11 13 1510 12 14 16
B-CAN Low:
Blue/Black, pin 4
(+) Accessory:
Green, pin 28
Required for
vehicle
takeover
12345678910
11 12 18
17
13 14 15 16
(+) Ignition Output
(+) Ignition:
Blue, pin 36
(+) 12V
31 1
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30
I/P-A Fusebox/Smart
Junction Box
(White conn. front
of fusebox/smart
junction box)
Not required in D2D mode.
Page 3
Installation Type 1
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65
TX
(-) Ground
RX
(+)12V
14 12 2
Rev.: 20170512
Platform: DBALL2
Firmware: HYUNDAI9
© 2017 Directed. All rights reserved.

Rev.: 20170512
Platform: DBALL2
Firmware: HYUNDAI9
© 2017 Directed. All rights reserved.
Type 1 - Vehicle Wiring Reference Chart
MC11 Gray 48-pin conn.
(located in driver kick panel)
10
37 29 22 18
11
38 30 23 19
12
39 31 20
1721
36 28
1
2
3
4
5
6
7
8
9
13
14
15
16
4
5
6
7
32
33
34
35
40
41
42
43
44
45
46
47
48
M01 Black16-pin conn.
(at Headlight/Wiper Switch)
1 3 5 72 4 6 8
9 11 13 1510 12 14 16
Page 4
I/P-F White 18-pin conn.
(located rear of fusebox
/ Smart Junction Box)
12345678910
11 12 18
17
13 14 15 16
I/P-A White 41-pin conn.
(located front of fusebox)
Front of Fusebox
31
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30
Function Color Pin Polarity Location Color Pins
C-CAN High Green 6 Data OBDII diagnostic connector White 16
C-CAN Low Orange 14 Data OBDII diagnostic connector White 16
(MUX) Parking Lights Yellow 14 (+) M01 located at Headlight/Wiper Switch White 16
B-CAN High Green/Black 3 Data I/P-F located at Rear of Fusebox/Smart Junction Box White 18
B-CAN Low Blue/Black 4 Data I/P-F located at Rear of Fusebox/Smart Junction Box White 18
12V White 31 (+) I/P-A located at Front of Dash Fusebox White 41
Accessory Green 28 (+) MC11 located in Driver's kick panel Gray 48
Ignition Blue 36 (+) MC11 located in Driver's kick panel Gray 48
Starter Red/Black 31 (+) MC11 located in Driver's kick panel Gray 48
EMS COM Blue 20 Data MC11 located in Driver's kick panel Gray 48
Ignition Interrupt Green 6 Cut I/P-F located at Rear of Fusebox/Smart Junction Box White 18
Wire Information Connector Information
Hyundai Tucson (Smart Key) 2016

Rev.: 20170512
Platform: DBALL2
Firmware: HYUNDAI9
© 2017 Directed. All rights reserved.
42 1
831
25 19
1235
1033
27 21
1437
16
2228
39
932
26 20
1336
1134
1538
17
2329
40
44 3
46 5
43 2
45 4
47
41 2430 18
6
48 7
Remote
Starter
(-) GWR (Status)
(-) Ground (-) Ground
(-) Lock Output
(-) Unlock Output
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
(-) Trunk Output
FT CAN High: Orange/Green: 5
HS CAN Low: Tan: 4
HS CAN High: Tan/Black: 3
FT CAN Low: Orange/Brown: 6
(-) Ground: Black: 14(-) Ground
(+) 12V: Red: 13(+) 12V
(-) Hood Status Output: Blue/Red: 12
E-Brake Status Output: Black/White: 1
(-) E-Brake Status Input
(-) Door Status
(-) Trunk Status
(AC) Tach Input
(+) Brake Status
(-) Hood Status
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
(AC) Tach Output: Violet/White: 5
(+) Brake Status Output: Gray: 6
Diagnostic
Connector
OBDII
1 8
169
C-CAN High: Green, pin 6
C-CAN Low: Orange, pin 14
(MUX) Parking Lights Output: Violet/Brown: 9
7 Pink/White: (-) Parking Lights Input
(-) Parking Lights Output
(+) Accessory Output
(+) Starter Output
Ign. Interrupt (conn. side): Orange/Red: 10
Ign. Interrupt (veh.side): Yellow/Red: 11
EMS COM: Orange/Black: 11
(-) Ignition Status Output
Smart Key Ign. Interrupt: Green, pin 6
I/P-F Fusebox/Smart
Junction Box
(White conn. rear of
fusebox/Smart Junction Box)
B-CAN High:
Green/Black, pin 3
(+) Starter:
Red/Black,
pin 45
EMS COM: Blue, pin 3
MC11 Junction
(Blue conn. at driver kick panel)
CUT
(MUX) Parking Lights:
Yellow, pin 14
Headlight/Wiper Switch
(Black conn. at steering column)
1 3 5 72 4 68
9 11 13 1510 12 14 16
B-CAN Low:
Blue/Black, pin 4
(+) Accessory:
Green, pin 30
Required for
vehicle
takeover
12345678910
11 12 18
17
13 14 15 16
(+) Ignition Output
(+) Ignition:
Blue, pin 41
(+) 12V
(+) 12V: pin 31
31 1
41 11
2
3
4
1
5
6
7
8
9
10
19
20
39
40
14
15
17
18
16
34
35
37
38
36
24
25
27
28
26
12
13
22
23
32
33
21
29
30
I/P-A Fusebox/Smart
Junction Box
(White conn. front
of fusebox/smart
junction box)
Not required in D2D mode.
Page 5
Installation Type 2
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
10
DBALL2
RF
Prog. Button
LED
4
XKD2D65
TX
(-) Ground
RX
(+)12V
14 12 2