Xpresskit DBALL2 User manual

Installation Guide
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
Index
®Mazda is a its respective companyregistered trademark and property of .
The MA2 firmware for 2 is an all-in-one door lock and override module compatible with specificDBALL
Mazda vehicles.
This module can only be flashed and configured using Xpress at www.directechs.com orVIP
using the Directechs Mobile application for smartphones. Refer to the Module Programming
section 20on page for more information.
Vehicle Application Guide .....................................................................................................................................................02
Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )
Type 1 ...................................................................................................................................................................................03
T2ype ...................................................................................................................................................................................06
Type 3...................................................................................................................................................................................10
Type 4...................................................................................................................................................................................12
Type 5...................................................................................................................................................................................14
Type 6...................................................................................................................................................................................16
Type 7 ...................................................................................................................................................................................18
Programming
M ...........................................................................................................................................................20odule Programming
Method 1 (using 1 key and Key2GO) - Recommended Method ..........................................................................................21
M .......................................................................................................................................................22ethod 2 (using 2 keys)
M .................................................................................................................................................23odule Reset & Hard Reset
Web Programming for Key2GO ...........................................................................................................................................24
Feature & Option List ...........................................................................................................................................................25
Feature Programming...........................................................................................................................................................25
LED Diagnostics .....................................................................................................................................26& Troubleshooting
L ................................................................................................................................28imited One-Year Consumer Warranty
Q ........................................................................................................................................................29uick Reference Guide
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Vehicle Application Guide Page 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each
year allows you to determine which installation type should be used for your vehicle.
This feature is required if only one key is available. You can program the interface without the need for Key2Go if two
keys are present.
Key2 has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It usesGO
an array of servers to generate a duplicate of the original key, the installation of a remote starter without having toallowing
give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2 -compatible firmware are clearly indicated in the function list of each vehicle search result page and will alsoGO
appear on the flash page. Any first-time user must re-register to gain access to Key2 , and some additional informationGO
will be required to complete the registration process, such as your Directed account number and store name. Key2GO
requires an XKLoader.
Refer to page 19 of this guide for instructions on how to program features using Key2 .GO
Vehicles
2016
2015
2014
2013
2012
2011
2010
2009
2008
2007
2006
2005
2004
2003
2002
PK-Immobilizer Bypass-Data No Key Req'd
CC-Power Windows Rolldown
CC-Power Windows Rollup
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Trunk / Hatch Release
Key2GO
RS-SmartStart
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
SS-Factory Alarm Trigger Monitoring
ST-Brake Status (foot brake)
ST-Door Locks Status
ST-E-Brake Status
Mazda
21111 • •••••D••••D•D•
31111 ••••••••••D••••D•D•
3555555 • • • •D• • • • • •
5111111 • • • • • •D• • • •
555555 • • • •D• • • • • •
611111 ••••••••••D••••D•D•
6222222 • • • •D• • • • • •
B-Series 333333333• •D• • • • •
CX-7 11 •••••••• •D••••D•D•
CX-7 222 • • • •D• • • • •
CX-7 (Smart Key) 111 •••••••• •D••••D•D•
CX-7 (Smart Key) 222 • • • •D• • • • •
CX-9 4444 •••••••• •D••••D•D•
CX-9 2222 • ••••D••••••
CX-9 (Smart Key) 4444 •••••••• •D••••D•D•
CX-9 (Smart Key) 2222 • ••••D••••••
MazdaSpeed3 2222 • •• ••D•••• • •
MazdaSpeed6 222 • •• ••D•••• • •
MX-5 Miata 2222222222 • • • • •D• • • • • •
RX-8 22222222 • • • • •D• • • • • •
Tribute 6666777 • • •D• • • • • •
Legend:
D: Data to Data (D2D) only AV: Horn & Lights Controls PK: Transponder & Immobilizer Override
•: D2D and Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls RS: Remote Start & Engine Controls
FOB: Sync CAN Interface w/ FOB Remote SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Page 3
Installation Type 1
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the diagnostic connector.OBDII
Remote
Starter
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(+) 12V: 13Red:
(+) 12V
(-) Ground: 14Black:
Passive Anti-Theft Security System ( ) connectorsPATS
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
Aux 1 & 2 Output: ONLY if equipped with front one-touch power
windows with auto up/down feature and global open.
[]1( ) Tach InpuAC t
(-) Door Status Input
(+) Brake Sense Input
Data : 11RX Orange/Black:
( ) Door Lock Output: 9MUX Violet/Brown:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
1234
5
6
Ground RX TX Ignition
A
87654321
Ground RX TXIgnition
B
(-) E-Brake Status Output: 1Black/White:
[]2(-) Hood Status Output: 12Blue/Red:
[]2(-) Hood Sense Input
(-) E-Brake Sense Input
Diagnostic
connector OBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: inP6
HS CAN Low: in 1P4
5: (-) Power ll-down InputViolet/Black: Windows Ro
4: (-) Power ll-up InputWhite/Violet: Windows Ro
C
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
2DBALL
4
Ignition Ground
32
TX RX
1
See Reference
Chart for Door Lock
MUX wire in vehicle.
(-) Ground
(-) (Status)GWR
(+) Ignition Output
(+) Accessory Output
(+) Starter Output
(-) OutputLock
(-) Unl Outputock
(+) 12V Input
Ignition Connector
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details.
( utput-) Trunk Release O [3]
(-) Parking Lights
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
Data : 10TX Yellow/Black:
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 4
Type 1 - Vehicle Wiring Reference Chart
Function Wire Color Pin Polarity Location
Color Pins
Mazda 2 2011-2014
12V Red 3 (+) Ignition switch. White 6
Ignition Black/Yellow 5 (+) Ignition switch. White 6
Accessory Black/Red 1 (+) Ignition switch. White 6
Starter Black/Blue 2 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Gray 4 Data
Immobilizer Module around ignition switch.
(PATS connector A).
White 6
TX Green 3 Data
Immobilizer Module around ignition switch.
(PATS connector A).
White 6
Parking Light Brown/White 8 (-) Headlight switch. White 12
Trunk Release Orange/Blue 2 5-Wire BCM behind glove box. Gray 16
Door Lock (WO/Alarm) Pink 20 MUX BCM behind glove box. Gray 24
Door Lock (W/Alarm) Green 2 MUX BCM behind glove box. Gray 24
Mazda 3 2010-2013
12V Orange 8 (+) Ignition switch. White 8
Ignition Blue 1 (+) Ignition switch. White 8
Accessory White 6 (+) Ignition switch. White 8
Starter Lt. Green 5 (+) Ignition switch. White 8
HS CAN High White 6 Data OBDII. Black 16
HS CAN Low Red 14 Data OBDII. Black 16
RX Blue 1 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
TX Lt. Blue 2 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
Parking Light Gray 23 (-) BCM Above Driver kick panel. White 24
Trunk Release Brown 8 (-) BCM Above Driver kick panel. White 24
Door Lock (WO/Alarm) Lt. Green 14 MUX BCM Above Driver kick panel. White 24
Door Lock (W/Alarm) Green 13 MUX BCM Above Driver kick panel. White 24
Mazda 5 2011-2016
12V Blue/Black 8 (+) Ignition switch. White 8
Ignition Blue 1 (+) Ignition switch. White 8
Accessory Black/Red 6 (+) Ignition switch. White 8
Starter Blue/Red 5 (+) Ignition switch. White 8
HS CAN High Green/Yellow 6 Data OBDII. Black 16
HS CAN Low Red/Yellow 14 Data OBDII. Black 16
RX Gray 1 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
TX Blue/Orange 2 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
Parking Light Brown/Red 23 (-) BCM behind glove box. Blue 24
Trunk Release Violet/Yellow 8 (-) BCM behind glove box. White 24
Door Lock (W/Alarm) Blue 14 MUX BCM behind glove box. White 24
Wire Information
Connector Information

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 5
Type 1 - Vehicle Wiring Reference Chart
Wire Information Connector Information
Function Wire Color Pin Polarity Location
Color Pins
Mazda 6 2009-2013
12V Red/Blue 6 (+) Ignition switch. White 6
Ignition Green/Yellow 2 (+) Ignition switch. White 6
Accessory Pink/Yellow 4 (+) Ignition switch. White 6
Starter Gray/Red 1 (+) Ignition switch. White 6
HS CAN High Gray/Red 6 Data OBDII. Black 16
HS CAN Low Blue/Red 14 Data OBDII. Black 16
RX White/Green 3 Data
Immobilizer Module around ignition switch.
(PATS connector B).
White 8
TX Gray/Orange 4 Data
Immobilizer Module around ignition switch.
(PATS connector B).
White 8
Parking Light Black/White 14 (-) Headlight switch. White 17
Trunk Release Black/Red 28 (-) BCM Above Driver kick panel. White 30
Door Lock (WO/Alarm) Black/White 4 MUX BCM Above Driver kick panel. White 16
Door Lock (W/Alarm) Black 14 MUX BCM Above Driver kick panel. White 16
Mazda CX-7 2010-2011
12V Red 6 (+) Ignition switch. White 6
Ignition Dk. Green/Yellow 2 (+) Ignition switch. White 6
Accessory Pink/Yellow 4 (+) Ignition switch. White 6
Starter Gray/Red 1 (+) Ignition switch. White 6
HS CAN High Gray/Dk. Blue 6 Data OBDII. Black 16
HS CAN Low Dk. Blue/White 14 Data OBDII. Black 16
RX White/Dk. Green 1 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
TX Gray/Orange 2 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
Parking Light Black/Dk. Blue 14 (-) Headlight switch. White 17
Trunk Release Black/Red 17 (-) BCM Above Driver kick panel. White 30
Door Lock (WO/Alarm) Green/Red 14 MUX BCM Above Driver kick panel. White 30
Door Lock (W/Alarm) Black/White 11 MUX BCM Above Driver kick panel. White 30
Mazda CX-7 2010-2012 (Smart Key)
12V Red 6 (+) Ignition switch. White 6
Ignition Dr. Green/Yellow 2 (+) Ignition switch. White 6
Accessory Pink/Yellow 4 (+) Ignition switch. White 6
Starter Gray/Red 1 (+) Ignition switch. White 6
HS CAN High Gray/Dk. Blue 6 Data OBDII. Black 16
HS CAN Low Dk. Blue/White 14 Data OBDII. Black 16
RX White/Dk. Green 1 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
TX Gray/Orange 2 Data
Immobilizer Module around ignition switch.
(PATS connector C).
White 4
Parking Light Black/Dk. Blue 14 (-) Headlight switch. White 17
Trunk Release Black/Red 17 (-) BCM Above Driver kick panel. White 30
Door Lock (WO/Alarm) Green/Red 14 MUX BCM Above Driver kick panel. White 30
Door Lock (W/Alarm) Black/White 11 MUX BCM Above Driver kick panel. White 30

Page 6
Installation Type 2
Remote
Starter
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(+) 12V: 13Red:
(+) 12V
(-) Ground: 14Black:
See Reference
Chart for Door Lock
wire in vehicle.MUX
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
[]1( ) Tach InpuAC t
(-) Door Status Input
[]2(-) Hood Status Input
(+) Brake Status Input
TX: 10Yellow/Black:
[]2(-) Hood Status Output: 12Blue/Red:
RX: 11Orange/Black:
( ) Door Lock Output: 9MUX Violet/Brown:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
(-) E-Brake Status Output: 1Black/White:
(-) E-Brake Status Input
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
DBALL2
Diagnostic onnectorCOBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: inP6
HS CAN Low: in 1P4
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
(-) Ground
(-) (Status)GWR
(+) Ignition Output
(+) Accessory Output
(+) Starter Output
(-) OutputLock
(-) Unl Outputock
(+) 12V Input
Ignition Connector
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details.
( utput-) Trunk Release O [3]
(-) Parking Lights Output
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
Remote
Starter
4123
Passive Anti-Theft
Security System (PATS)
connector
RX: Pin 1
TX: Pin 2
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 7
Type 2 - Vehicle Wiring Reference Chart
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Mazda 6 2003-2008
12V Black or Black/Yellow 6 (+)
Ignition switch. White 6
Ignition Blue 2 (+) Ignition switch. White 6
Accessory Black/Red 4 (+) Ignition switch. White 6
Starter Black/Blue 1 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Orange/Blue or Gray 1 Data Immobilizer Module around ignition switch. White 4
TX Green or Yellow/Green 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Red/White 14 (-) Headlight switch. White 17
Trunk Release Yellow 1 (-) Trunk release switch. White 2
Door Lock (WO/Alarm) Lt. Green 7 MUX BCM drivers kick. White 24
Door Lock (W/Alarm) Blue or Blue/White 17 MUX BCM drivers kick. White 24
Mazda CX-7 2007-2009
12V Red 6 (+) Ignition switch. White 6
Ignition Green/Yellow 2 (+) Ignition switch. White 6
Accessory Pink/Yellow 4 (+) Ignition switch. White 6
Starter Gray/Red 1 (+) Ignition switch. White 6
HS CAN High Gray/Violet 6 Data OBDII. Black 16
HS CAN Low Blue/White 14 Data OBDII. Black 16
RX White/Green 1 Data Immobilizer Module around ignition switch. White 4
TX Gray/Orange 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Black/Red 14 (-) Headlight switch. White 17
Door Lock (WO/Alarm) Blue/Black or Green/Red 5 or 15 MUX BCM above Drivers kick. White 30
Door Lock (W/Alarm) Black/White 1 MUX BCM above Drivers kick. White 30
Mazda CX-7 2007-2009 (Smart Key)
12V Red 6 (+) Ignition switch. White 6
Ignition Green/Yellow 2 (+) Ignition switch. White 6
Accessory Pink/Yellow 4 (+) Ignition switch. White 6
Starter Gray/Red 1 (+) Ignition switch. White 6
HS CAN High Gray/Violet 6 Data OBDII. Black 16
HS CAN Low Blue/White 14 Data OBDII. Black 16
RX White/Green 1 Data Immobilizer Module around ignition switch. White 4
TX Gray/Orange 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Black/Red 14 (-) Headlight switch. White 17
Door Lock (WO/Alarm) Blue/Black or Green/Red 5 or 15 MUX BCM above Drivers kick. White 30
Door Lock (W/Alarm) Black/White 1 MUX BCM above Drivers kick. White 30
Mazda CX-9 2007-2010
12V Red 6 (+) Ignition switch. White 6
Ignition Blue 2 (+) Ignition switch. White 6
Accessory Black/Red 4 (+) Ignition switch. White 6
Starter Black/Blue 1 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Blue/Orange 1 Data Immobilizer Module around ignition switch. White 4
TX Blue/Yellow 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Brown or Brown/White 14 (-) Headlight switch. White 17
Trunk Release White/Green & White/Black 1 & 3 Short
Power liftgate switch, use relay to short White/Green and
White/Black together.
White 6
Door Lock (WO/Alarm) Violet/White 26 MUX BCM above Drivers kick. White 30
Door Lock (W/Alarm) Lt. Green 12 MUX
BCM above Drivers kick. White 30

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 8
Type 2 - Vehicle Wiring Reference Chart
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Mazda CX-9 2007-2010 (Smart Key)
12V Red 6 (+) Ignition switch. White 6
Ignition Blue 2 (+) Ignition switch. White 6
Accessory Black/Red 4 (+) Ignition switch. White 6
Starter Black/Blue 1 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Blue/Orange 1 Data Immobilizer Module around ignition switch. White 4
TX Blue/Yellow 2 Data
Immobilizer Module around ignition switch. White 4
Parking Light Brown or Brown/White 14 (-) Headlight switch. White 17
Trunk Release White/Green & White/Black 1 & 3 Short
Power liftgate switch, use relay to short White/Green and
White/Black together.
White 6
Door Lock (WO/Alarm) Volet/White 26 MUX BCM above Drivers kick. White 30
Door Lock (W/Alarm) Lt. Green 12 MUX BCM above Drivers kick. White 30
Mazda MazdaSpeed3 2006-2009
12V Red 4 (+)
Ignition switch. White 6
Ignition Green/Yellow 1 (+) Ignition switch. White 6
Accessory Pink/Yellow 6 (+) Ignition switch. White 6
Starter Gray/Black 5 (+) Ignition switch. White 6
HS CAN High Gray/Violet 6 Data OBDII. Black 16
HS CAN Low Blue/White 14 Data OBDII. Black 16
RX White/Green 1 Data Immobilizer Module around ignition switch. White 4
TX Gray/Orange 2 Data
Immobilizer Module around ignition switch. White 4
Parking Light Black/White 1 (-) Headlight switch. White 12
Door Lock (WO/Alarm) Green/Red to Black/Blue N/A MUX Drivers kick panel. White N/A
Door Lock (W/Alarm) Black/Blue N/A MUX Drivers kick panel. White N/A
Mazda MazdaSpeed6 2006-2008
12V Black/Yellow 6 (+) Ignition switch. White 6
Ignition Blue 2 (+) Ignition switch. White 6
Accessory Black/Red 4 (+) Ignition switch. White 6
Starter Black/Blue 1 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Orange/Blue or Gray 1 Data Immobilizer Module around ignition switch. White 4
TX Green or Yellow/Green 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Red/White 14 (-) Headlight switch. White 17
Trunk Release Yellow 1 (-) Trunk release switch. White 2
Door Lock (WO/Alarm) Lt. Green 7 MUX BCM drivers kick. White 24
Door Lock (W/Alarm) Blue or Blue/White 17 MUX BCM drivers kick. White 24
Mazda MX-5 Miata 2006-2015
12V White/Green 3 (+) Ignition switch. White 6
Ignition Green/White 2 (+) Ignition switch. White 6
Accessory Pink/Black 4 (+) Ignition switch. White 6
Starter White/Blue 1 (+) Ignition switch. White 6
HS CAN High Blue/White 6 Data OBDII. Black 16
HS CAN Low Green/Black 14 Data OBDII. Black 16
RX Blue/Orange or Violet 1 Data Immobilizer Module around ignition switch. White 4
TX Yellow/Black or Gray/Blue 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Brown/Black 14 (-) Headlight switch. White 17
Door Lock (WO/Alarm) Brown/White 10 MUX Keyless Control Module above drivers kick. White 27
Door Lock (W/Alarm) Gray/Red 3 MUX Keyless Control Module above drivers kick. White 27

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 9
Type 2 - Vehicle Wiring Reference Chart
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Mazda RX-8 2004-2011
Ignition Black/Yellow or Blue/Black 2 (+) Ignition switch. White 6
Accessory Blue/Green 6 (+) Ignition switch. White 6
Starter White/Blue 1 (+) Ignition switch. White 6
HS CAN High Blue/White 6 Data OBDII. Black 16
HS CAN Low Green/Black 14 Data OBDII. Black 16
RX Yellow/Black 1 Data Immobilizer Module around ignition switch. White 4
TX Blue/Orange 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Lt. Green 14 (-) Headlight switch. White 17
Door Lock (WO/Alarm) Lt. Green N/A MUX Driver door harness. N/A N/A
Door Lock (W/Alarm) Green/Red N/A MUX Driver door harness. N/A N/A
12V Green or Orange N/A (+) Drivers kick panel. N/A N/A

Page 10
Installation Type 3
Remote
Starter
(+) Ignition
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(+) 12V: 13Red:
(+) 12V
[]1( ) Tach InpuAC t
(-) Door Status Input
[]2(-) Hood Status Input
(+) Brake Status Input
TX: 10Yellow/Black:
[]2(-) Hood Status Output: 12Blue/Red:
RX: 11Orange/Black:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
(-) E-Brake Status Output: 1Black/White:
(-) E-Brake Status Input
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
DBALL/
2DBALL
Diagnostic onnectorCOBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: inP6
HS CAN Low: in 1P4
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
Ignition Connector
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details.
(-) Ground
(-) (Status)GWR
(+) Ignition Output
(+) Accessory
(+) Starter Output
(+) Parking Lights
(-) OutputLock
(+) 12V Input
(-) Trunk Release Output [3]
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
(-) Ground: 14Black:
4123
RX: Pin 3
TX: Pin 4
Passive Anti-Theft
Security System (PATS)
connector
(-) Unl Outputock
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 11
Type 3 - Vehicle Wiring Reference Chart
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins
Mazda B-Series 2002-2006
12V Yellow N/A (+) Ignition switch. White 6
Ignition Lt. Green/Violet N/A (+) Ignition switch. White 6
Accessory Gray/Yellow N/A (+) Ignition switch. White 6
Starter Red/Lt. Blue N/A (+) Ignition switch. White 6
HS CAN High (2004-2006) White/Lt. Green 6 Data OBDII. Black 16
HS CAN Low (2004-2006) Pink/Lt Green 14 Data OBDII. Black 16
RX Gray/Orange 3 Data
Immobilizer Module around ignition switch. White 4
TX White/Lt. Green 4 Data
Immobilizer Module around ignition switch. White 4
Parking Light Brown 3 (+) Headlight switch. White 11
Door Lock Pink/Yellow 5 (-) SJB (Smart Junction Box) Passenger kick panel. Black 30
Door unlock Pink/Green 9 (-) SJB (Smart Junction Box) Passenger kick panel. Black 30
Mazda B-Series 2007-2010
12V Red 2 (+) Ignition switch. Gray 13
Ignition White/Orange 1 (+) Ignition switch. Gray 13
Accessory Brown/Yellow 8 (+) Ignition switch. Gray 13
Starter Blue/White 5 (+)
Ignition switch. Gray 13
HS CAN High (2004-2006) Blue/White 6 Data OBDII. Black 16
HS CAN Low (2004-2006) White 14 Data OBDII. Black 16
RX Blue/Gray 3 Data Immobilizer Module around ignition switch. Green 4
TX Violet/Brown 4 Data Immobilizer Module around ignition switch. Green 4
Parking Light Violet/White 5 (+) Headlight switch. White 10
Door Lock Gray/Yellow 5 (-) Driver kick panel. Black 32
Door unlock Violet/Gray 9 (-) Driver kick panel. Black 32

Page 12
Installation Type 4
Remote
Starter
(-) (Status)GWR
(+) Ignition Output
(+) Accessory 2 Output
(+) Starter Output
( utput+) Brake O
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(+) 12V: 13Red:
(+) 12V
(-) Ground: 14Black:
(-) Ground
(-) OutputLock
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
[]1( ) Tach InpuAC t
(-) Door Status Input
[]2(-) Hood Status Input
(+) Brake Status Input
TX: 10Yellow/Black:
[]2(-) Hood Status Output: 12Blue/Red:
RX: 11Orange/Black:
( ) Door Lock Output: 9MUX Violet/Brown:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
(-) E-Brake Status Output: 1Black/White:
(-) E-Brake Status Input
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
DBALL2
Diagnostic onnectorCOBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: inp6Red,
HS CAN Low: in 1p4Blue,
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
(-) Unl Outputock
(+) 12V Input
(-) Ground
Ignition Connector
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details.
See Reference
Chart for Door Lock
MUX wire in vehicle.
( utput-) Trunk Release O [3]
(-) Parking Lights
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
4123
Passive Anti-Theft
Security System (PATS)
connector
RX: , pin 1Blue/Orange
TX: , pin 1Blue/Yellow
(+) Accessory Output
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 13
Type 4 - Vehicle Wiring Reference Chart
Function Wire Color Pin Polarity Location
Color Pins
Mazda CX-9 2011-2014
12V Red 6 (+) Ignition switch. White 6
Ignition Blue 2 (+) Ignition switch. White 6
Accessory Black/Red 4 (+) Ignition switch. White 6
Accessory 2 Black/White 5 (+) Ignition switch. White 6
Starter Black/Blue 1 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Blue/Orange 1 Data Immobilizer Module around ignition switch. White 4
TX Blue/Yellow 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Brown or Brown/White 14 (-) Headlight switch. White 17
Door Lock (WO/ Alarm) Violet/White 26 MUX
BCM in drivers kick. White 30
Door Lock (W/ Alarm) Lt. Green 12 MUX BCM in drivers kick. White 30
Brake Green/Yellow N/A (+) Driver kick panel. N/A N/A
Trunk Input Lt. Green/Red 10 (-) BCM in drivers kick. White 24
Trunk Release White/Green and White/Black 2 and 4 Short
Power lifgate switch, use relay to short
White/Green and White Black together.
White 12
Mazda CX-9 (Smart Key) 2011-2014
12V Red 6 (+) Ignition switch. White 6
Ignition Blue 2 (+) Ignition switch. White 6
Accessory Black/Red 4 (+) Ignition switch. White 6
Accessory 2 Black/White 5 (+) Ignition switch. White 6
Starter Black/Blue 1 (+) Ignition switch. White 6
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
RX Blue/Orange 1 Data Immobilizer Module around ignition switch. White 4
TX Blue/Yellow 2 Data
Immobilizer Module around ignition switch. White 4
Parking Light Brown or Brown/White 14 (-) Headlight switch. White 17
Door Lock (WO/ Alarm) Violet/White 26 MUX BCM in drivers kick. White 30
Door Lock (W/ Alarm) Lt. Green 12 MUX
BCM in drivers kick. White 30
Brake Green/Yellow N/A (+) Driver kick panel. N/A N/A
Trunk Input Lt. Green/Red 10 (-)
BCM in drivers kick. White 24
Trunk Release White/Green and White/Black 2 and 4 Short
Power lifgate switch, use relay to short
White/Green and White Black together.
White 12
Wire Information
Connector Information

Page 14
Installation Type 5
Remote
Starter
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(+) 12V: 13Red:
(+) 12V
(-) Ground: 14Black:
See Reference
Chart for Door Lock
wire in vehicle.MUX
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
[]1( ) Tach InpuAC t
(-) Door Status Input
[]2(-) Hood Status Input
(+) Brake Status Input
TX: 10Yellow/Black:
[]2(-) Hood Status Output: 12Blue/Red:
RX: 11Orange/Black:
( ) Door Lock Output: 9MUX Violet/Brown:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
(-) E-Brake Status Output: 1Black/White:
(-) E-Brake Status Input
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
DBALL2
Diagnostic onnectorCOBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: inP6
HS CAN Low: in 1P4
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
MS CAN High: Orange/Green: 5
Ms CAN Low: Orange/Brown: 6
(-) (Status)GWR
(+) Ignition Output
(+) Accessory Output
(+) Starter Output
(-) Unl Outputock
(+) 12V Input
Ignition Connector
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details.
( utput-) Trunk Release O [3]
(-) Parking Lights
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
(-) Ground
MS CAN High: inP3
MS CAN Low: in 1P1
4123
Passive Anti-Theft
Security System (PATS)
connector
RX: Pin 1
TX: Pin 2
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 15
Type 5 - Vehicle Wiring Reference Chart
Function Wire Color Pin Polarity Location
Color Pins
Mazda 3 2004-2009
12V Red 4 (+) Ignition switch. White 8
Ignition Green/Yellow 1 (+) Ignition switch. White 8
Accessory Pink/Yellow 6 (+) Ignition switch. White 8
Starter Gray/Black 5 (+) Ignition switch. White 8
HS CAN High Gray/Violet 6 Data OBDII. Black 16
HS CAN Low Blue/White 14 Data OBDII. Black 16
MS CAN High Gray/Violet 3 Data OBDII. Black 16
MS CAN Low Blue/White 11 Data OBDII. Black 16
RX White/Green 1 Data Immobilizer Module around ignition switch. White 4
TX Gray/Orange 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Black/White 1 (-) Headlight switch. White 12
Door Lock (WO/Alarm) Green/Red to Black/Blue N/A MUX Drivers kick panel. N/A N/A
Door Lock (W/Alarm) Black/Blue N/A MUX Drivers Kick panel. N/A N/A
Mazda 5 2006-2007
12V Black/Yellow 8 (+) Ignition switch. White 8
Ignition Blue 1 (+) Ignition switch. White 8
Accessory Black/Red 6 (+) Ignition switch. White 8
Starter Black/Blue 5 (+) Ignition switch. White 8
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low Blue 14 Data OBDII. Black 16
MS CAN High Blue/Whie 3 Data OBDII. Black 16
MS CAN Low Gray 11 Data OBDII. Black 16
RX Pink/Black 1 Data Immobilizer Module around ignition switch. White 4
TX Green 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Brown/Red 1 (-) Headlight switch. White 12
Door Lock Blue N/A MUX Drivers kick panel. N/A N/A
Mazda 5 2008-2010
12V Black/Yellow 8 (+) Ignition switch. White 8
Ignition Blue 1 (+) Ignition switch. White 8
Accessory Black/Red 6 (+) Ignition switch. White 8
Starter Black/Blue 5 (+) Ignition switch. White 8
HS CAN High Red 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
MS CAN High Violet 3 Data OBDII. Black 16
MS CAN Low Gray 11 Data OBDII. Black 16
RX Pink/Black 1 Data Immobilizer Module around ignition switch. White 4
TX Green 2 Data Immobilizer Module around ignition switch. White 4
Parking Light Brown/Red 1 (-) Headlight switch. White 12
Door Lock Blue N/A MUX Drivers kick panel. N/A N/A
Wire Information
Connector Information

Page 16
Installation Type 6
Remote
Starter
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(+) 12V: 13Red:
(+) 12V
[]1( ) Tach InpuAC t
(-) Door Status Input
[]2(-) Hood Status Input
(+) Brake Status Input
TX: 10Yellow/Black:
[]2(-) Hood Status Output: 12Blue/Red:
RX: 11Orange/Black:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
(-) E-Brake Status Output: 1Black/White:
(-) E-Brake Status Input
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
DBALL2
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
Ignition Connector
Refer to the Vehicle Wiring
Reference Information for
wire and connector details.
(-) (Status)GWR
(+) Ignition Output
(+) Accessory Output
(+) Starter Output
(-) OutputLock
(-) Unl Outputock
(+) 12V Input
(-) Trunk Release Output [3]
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
(-) Ground: 14Black:
Diagnostic onnectorCOBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: pin 6White/Blue,
HS CAN Low: in 1p4White,
MS CAN High: Orange/Green: 5
Ms CAN Low: Orange/Brown: 6
(-) Ground
MS CAN High:
Gray/Orange, pin 3
MS CAN Low:
Violet/Orange, pin 11
1432
RX: pin 3Violet/Gray,
TX: pin 4Yellow/Orange,
Passive Anti-Theft
Security System (PATS)
connector
(+) Parking Lights
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 17
Type 6 - Vehicle Wiring Reference Chart
Function Wire Color Pin Polarity Location
Color Pins
Mazda Tribute 2008-2011
12V Blue/Red 4 (+) Ignition switch. Black 7
Ignition White/Orange 1 (+) Ignition switch. Black 7
Accessory Violet/Green 6 (+) Ignition switch. Black 7
Starter Blue/White 7 (+) Ignition switch. Black 7
HS CAN High White/Blue 6 Data OBDII. Black 16
HS CAN Low White 14 Data OBDII. Black 16
MS CAN High Gray/Orange 3 Data OBDll Black 16
MS CAN Low Violet/Orange 11 Data OBDll Black 16
RX Violet/Gray 3 Data Immobilizer Module around ignition switch. Black 4
TX Yellow/Orange 4 Data Immobilizer Module around ignition switch. Black 4
Parking Light Violet/White N/A (+) Driver kick panel. N/A N/A
Door Lock Blue/Green 17 (-) Driver door harness. N/A N/A
Door unlock Yellow/Violet 4 (-) Driver door harness. N/A N/A
Rear liftgate Brown 7 (-) SJB (Smart Junction Box) right side of center console. Gray 26
Wire Information
Connector Information

Page 18
Installation Type 7
(+) 12V: 13Red:
(+) 12V
TX: 10Yellow/Black:
[]2(-) Hood Status Output: 12Blue/Red:
RX: 11Orange/Black:
[]1( ) Tach Output: 5AC Violet/White:
(-) Door Status Output: 3Green/White:
(+) Brake Status Output: 6Gray:
(-) E-Brake Status Output: 1Black/White:
P#: 2D65XKD
TX
(-) Ground
RX
(+)12V
10
RF
Prog Button.
LED
4
14 12 2
DBALL/
2DBALL
Diagnostic onnectorCOBDII
(connector side view)
18
169
HS CAN High: 3Tan/Black:
HS CAN Low: 4Tan:
HS CAN High: inp6White,
HS CAN Low: in 1p4Black,
With the exception of the Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).OBDII
(-) Ground: 14Black:
4123
RX: pin 3Red/Black,
TX: pin 4Brown/Orange,
Passive Anti-Theft
Security System (PATS)
connector
Not required in D2D mode.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2] Only if vehicle is equipped with OEM hood pin.
[]3Trunk release output is ONLY required if trunk is not supported in data.
Remote
Starter
(-) (Status)GWR
(+) Ignition Output
(+) Starter Output
9: (+) Ignition InputPink:
10: (-) (Status) InputBlue/White: GWR
(-) OutputLock
1: (-) Lock InputGreen:
2: (-) Unlock InputBlue:
[]1( ) Tach InpuAC t
(-) Door Status Input
[]2(-) Hood Status Input
(+) Brake Status Input
(-) E-Brake Status Input
(-) Unl Outputock
(+) 12V Input
(-) Ground
( utput-) Trunk Release O [3]
(-) Parking Lights
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details
(+) Accessory Output
Ignition Connector
Refer to the Vehicle Wiring
Reference Chart for wire
and connector details.
See Reference
Chart for Door Lock
wire in vehicle.MUX
( ) Door Lock Output: 9MUX Violet/Brown:
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.

Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.
Page 19
Type 7 - Vehicle Wiring Reference Chart
Function Wire Color Pin
Polarit
Location
Color Pins
Mazda Tribute 2005-2007
12V Red 4 (+) Ignition switch. Black 7
Ignition Lt. Green/Violet 1 (+)
Ignition switch. Black 7
Accessory Black/Lt. Green 6 (+) Ignition switch. Black 7
Starter Tan/Lt. Blue 7 (+) Ignition switch. Black 7
HS CAN High White 6 Data OBDII. Black 16
HS CAN Low Black 14 Data OBDII. Black 16
RX Red/Black 3 Data Immobilizer Module around ignition switch. Green 4
TX Brown/Orange 4 Data Immobilizer Module around ignition switch. Green 4
Parking Light Brown N/A (+) Driver kick panel. N/A N/A
Door Lock/Unlock Pink/White MUX N/A Driver kick panel. N/A N/A
Wire Information
Connector Information

Page 20
Module Programming
Refer to the LED Diagnostics section on page for more information and for troubleshooting purposes.26
Go to the next page t complete the module programming.o
Note for Knob style vehicles:
Before starting the programming sequence, remove the metal key by sliding it out from the . TheOEM FOB
removal of the knob cover is necessary.
1- With the start knob in the position, remove the auxiliary key from the advanced key.OFF
2- Remove the cover of the start knob by pulling it outward while pressing both buttons on each side of the knob.
3- Proceed to module programming below.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to
the module, then connect the 4-pin D2D harness.
D2D Installation
W W Installation2
If required for your installation, connect the 10-pin and 12-pin harnesses to the
module, then connect the 14-pin harness to the module.
10-pin
D2D
1st
12-pin
14-pin
2nd
3rd
10-pin
D2D
1st
4th
12-pin
14-pin
2nd
3rd
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the button.Flash Module
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select and follow the on screenFLASH YOUR MODULE
instructions.
Rev.: 20170926
Platform: DBALL2
Firmware: MA2
© 2017 Directed. All rights reserved.